Siegenia Aubi
Sensoair Z-Wave CO2 Sensor - Wall
SKU: SIG_SENS_W
Quickstart
This is a
A single Click on the Z-Wave Button on the bottom side to confirm inclusion, exclusion and association.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
The concentration of CO2 in the air is measured in parts per million (ppm). The CO2 concentration outdoors is approx. 350 ppm on average. A level of above approx. 800 ppm negatively impacts on our well-being. The concentration of CO2 in a room depends on the number of people in the room, the length of time that they spend in that room and the air exchange rate. For example, a 60 m2 room that contains two people and has an air exchange rate of 1 will reach a CO2 concentration of 900 ppm. Without ventilation, the concentration of CO2 in the room would increase to 1,500 ppm after two hours and 2,500 ppm after five hours. In order to measure air quality, SENSOAIR type wave uses two sensors to detect the carbon dioxide (CO2) concentration in closed rooms. The quality of the air that has been measured is indicated using a LED light and is transmitted via Z-Wave.
Installation
- Open the casing by removing the front part.
- Unblock the shaped disruption points for the screws and cable set.
- Pull the cable set through the cut-out and use the back part of the casing as a pattern for the screws.
- Connect the cable set as shown in the figure. You can power the device with 230V AC or 24V DC.
- Close the casing before the first power up.
Note:
- Use only indoors in dry and dust free rooms.
- Use only in an environmental temperatur from 5C - 40C.
- The device is NOT to be used with gas warning system or similar systems.
- Do not use solvents close to the device.
- Silicon vapours can cause malfunction.
- Use only with original accessories from SIEGENIA-AUBI.
- The installation should only be done by experienced professionals according to the mounting instructions.
- Use only in perfect technical condition. Do not make any modifications to the appliance.
- Make sure that the ventilation openings remain unobstructed and not be covered by furniture and other objects.
- Repairs should only be done by experienced professionals.
Product Usage
Before putting the system into service an automatic calibration has to be done.
Preconditions: The room has to be well ventilated. The room temperatur should be between 5C and 40C. There must be no persons or animals in the area of operation.
Calibration:
- Switching on power - calibration starts.
- Sensors are heated up and calibrated to 350 ppm - LED one time flashes green.
- After the calibration is done (approx. 30 minutes), the LED flashes continuously green. The device is ready to use now.
The SENSOAIR measures the carbon dioxide concentration (CO2) of the ambient air. The measured air qualitiy is shown with the LED lights.
| Reset to factory default | Push and hold the Z-Wave Button on the bottom side for 5 seconds to reset the device to factory settings. |
| Inclusion | Single Click the Z-Wave Button on the bottom side confirms inclusion and exclusion. |
| Exclusion | Single Click the Z-Wave Button on the bottom side confirms inclusion and exclusion. |
| NIF | Single Click the Z-Wave Button on the bottom side |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | Unsolicitated Sensor Reports |
Configuration Parameters
Parameter 1: Configuration
Contains bits for device settings. Size: 1 Byte, Default Value: 8d
| Setting | Description |
|---|---|
| Byte 1: 00000001 | Send unsolicitated reports when the C02 level hits 600, 800, 100, 1500, 2000 or 2500 ppm. |
| Byte 1: 00000010 | Enables regular unsolicited Sensor reports. |
| Byte 1: 00000100 | A BASIC Set command is send, when the sensor hits the defined CO2 level. |
| Byte 1: 00001000 | Enables broadcast reports. |
| Byte 1: 10000000 | Enables the front side LED. |
Parameter 2: Interval for unsolicited Sensor Report
The parameter defines how often a Sensor report shall be sent when enabled by parameter 1 Size: 2 Byte, Default Value: 001e
| Setting | Description |
|---|---|
| 00 - 127 | Value |
Technical Data
| Dimensions | 0.1600000x0.1000000x0.0450000 mm |
| Hardware Platform | ZM3102 |
| IP Class | IP 20 |
| Device Type | Routing Multilevel Sensor |
| Generic Device Class | Multilevel Sensor |
| Specific Device Class | Routing Multilevel Sensor |
| Firmware Version | 01.04 |
| Z-Wave Version | 02.4e |
| Certification ID | ZC08-09080006 |
| Z-Wave Product Id | 0081.00a0.0001 |
| Frequency | Europe - 868,4 Mhz |
| Maximum transmission power | 5 mW |