Quickstart

This is a secure Z-Wave Device for Europe. To run this device please connect it to your mains power supply. To add this device to your network execute the following action:

Press the button three times in rapid succession to put the sensor into inclusion mode.



Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

What is Z-Wave?

Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.

Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.

This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.

If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.

For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.

Product Description

Infrared motion detector with orientation light and Z-Wave interface for indoor power sockets.
Movement triggers lights, alarms and many other devices. For your convenience, safety and peace of mind. The integrated pyroelectric infrared detector senses the invisible heat radiated from moving objects (people, animals, etc.). The heat detected in this way is converted electronically into a signal that switches ON the interconnected load. Heat is not detected through obstacles, such as walls or panes of glass, and will therefore not activate the light. The infrared sensor can be used for switching light ON and OFF automatically. The unit is not suitable for burglar alarm systems as it is not tamperproof in the manner prescribed for such systems. The button activates and deactivates the functions programmed via the Smart Friends app. The orientation light can be switched ON and OFF via the sensor or the button on the MotionSwitch LED Z-Wave. The relevant setting can be programmed via the Smart Friends app. This device can be integrated into the Smart Friends system or any other Z-Wave network. Z-Wave is a wireless standard for interconnecting Z-Wave devices. The power-socket sensor can be used for wireless-based building automation.

Prepare for Installation / Reset

Please read the user manual before installing the product.

In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.

Reset to factory default

This device also allows to be reset without any involvement of a Z-Wave controller. This procedure should only be used when the primary controller is inoperable.

To set the sensor to "Reset", press the button three times in rapid succession and then press it once for several seconds.

Safety Warning for Mains Powered Devices

ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.

Installation

Fit sensor into the power socket so that it is aimed in the required direction.


 

Inclusion/Exclusion

On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.

Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.

Inclusion

Press the button three times in rapid succession to put the sensor into inclusion mode.

Exclusion

To put the sensor into exclusion mode, press the button three times in rapid succession.

Product Usage


A = MotionSwitch LED
B = Button
C = Sensor
D = Orientation light

Range:




Factory settings
Twilight level: 2000 lux
Time setting: 3 minutes

The motion detector will also work without being integrated into a Z-Wave network. In this case, the time setting is permanently set to 3 minutes. In this setting, the integrated LED light or a directly connected Z-Wave actuator will be activated. After the 40-second calibration phase, the motion detector is activated for sensor mode. The motion detector can now be integrated into the Z-Wave network. The settings can be made via Z-Wave network. 

Twilight setting
The twilight level can be infinitely varied in the range from 2 to 2000 lux via the Smart Friends app. 
Note: To adjust the detection zone in daylight, the control dial must be set to 2000 lux = daylight operation.

Quick trouble shooting

Here are a few hints for network installation if things dont work as expected.

  1. Make sure a device is in factory reset state before including. In doubt exclude before include.
  2. If inclusion still fails, check if both devices use the same frequency.
  3. Remove all dead devices from associations. Otherwise you will see severe delays.
  4. Never use sleeping battery devices without a central controller.
  5. Dont poll FLIRS devices.
  6. Make sure to have enough mains powered device to benefit from the meshing

Association - one device controls an other device

Z-Wave devices control other Z-Wave devices. The relationship between one device controlling another device is called association. In order to control a different device, the controlling device needs to maintain a list of devices that will receive controlling commands. These lists are called association groups and they are always related to certain events (e.g. button pressed, sensor triggers, ...). In case the event happens all devices stored in the respective association group will receive the same wireless command wireless command, typically a 'Basic Set' Command.

Association Groups:

Group Number Maximum Nodes Description
1 1 Lifeline
2 16 On/Off control
3 16 Notification Report
4 16 Ambient light
5 16 Button on/off
6 16 Button scene
7 16 Button dim

Configuration Parameters

Z-Wave products are supposed to work out of the box after inclusion, however certain configuration can adapt the function better to user needs or unlock further enhanced features.

IMPORTANT: Controllers may only allow configuring signed values. In order to set values in the range 128 ... 255 the value sent in the application shall be the desired value minus 256. For example: To set a parameter to 200 it may be needed to set a value of 200 minus 256 = minus 56. In case of a two byte value the same logic applies: Values greater than 32768 may needed to be given as negative values too.

Parameter 1: Duration time

Duration of light after motion detection.
Size: 2 Byte, Default Value: 180

Setting Description
5 - 900 Time in s

Parameter 2: Light threshold


Size: 2 Byte, Default Value: 100

Setting Description
0 Run Learn ambient light sequence.
2 - 2000 Threshold in lx

Parameter 5: Motion Radar Sensitivity


Size: 1 Byte, Default Value: 100

Setting Description
2 - 100 in %

Parameter 6: Brightness measuring interval


Size: 1 Byte, Default Value: 0

Setting Description
0 Function is off.
5 - 120 in min.

Parameter 8: Use external Ambient Light Value:

When GLOBAL_LIGHT mode is ON – device overrides its own light sensor values and uses Light report values from any Z-Wave light sensor instead – this has to be configured appropriately to send light automatically.If the last remote light level value is older than 30 minutes, the internal light value is used again until the next external value is received.
Size: 1 Byte, Default Value: 1

Setting Description
0 Disable
1 Enable

Parameter 9: Disable local control

Stupid mode ( bit 2 = 1 ):- has higher priority then slave mode.- LED is permanently on ( for simple power wall switch controlling ).

Slave mode ( bit 0 = 1 ):- only if included in Z-Wave network- useful for controlling via third-party sensor- LED is directly controlled via Z-Wave, internal sensors are not used for controlling it Central unit checking ( bit 1 = 1 ): ( useful especially for controlling via gateway )

When slave bit is 0: - device signalises fail of lifeline connection ( if this bit is zero, fail of lifeline connection is not signalised )When slave bit is 1: - device checks presence of Z-Wave device in lifeline group ( gateway ). If it is not present for 2 minutes ( testing repeatedly every 30 seconds ) device switches to normal mode in the same way as after the end of local disabled mode(ON_BEHAVIOUR)- the device checks every 1 minute for recovery of Lifeline connection.- if no lifeline specified - it works in normal mode

Be careful with this option, device stops using its own motion sensor in Slave and Stupid mode.

Size: 2 Byte, Default Value: 1

Setting Description
0 Slave mode
1 Central unit checking in slave mode
2 Stupid mode

Parameter 10: Off behaviour ( timeout )

Behaviour after BASIC OFF ( and similar commands ). If a transition ( even with zero change ) with a non-default duration is to be processed, the transition cannot be interrupted by any motion event in any motion event in any case.
Size: 2 Byte, Default Value: 10

Setting Description
0 LED is switched off and remains so until any new motion event ( local or remote ) is received.
1 - 209 LED is switched off and remains so until after a specified timeout once a new motion event ( local or remote ) is received. Timeout: 1..100 – 1 second ( 1 ) to 100 seconds ( 100 ) in 1-second resolution 101..200 – 1 minute ( 101 ) to 100 minutes ( 200 ) 1-minute resolution 201..209 – 1 hour ( 201 ) to 9 hours ( 209 ) in 1-hour resolution
255 LED is switched off for TIME ( cfg 1 ). It does not wait for a motion event and works normally via current motion evaluation.

Parameter 11: On behaviour ( timeout )

Behaviour after BASIC ON ( and similar commands ). If a transition ( even with zero change ) with a non-default duration is to be processed, the transition cannot be interrupted by any motion event in any case.
Size: 2 Byte, Default Value: 255

Setting Description
0 LED is switched on and remains so until any new motion event ( local or remote ) is received. It then works normally via current motion evaluation. Notice – during the day, this mode cannot be ended remotely due to motion events not being transmitted – only via local motion sensor if enabled.
1 - 209 LED is switched off and remains so until after a specified timeout once a new motion event ( local or remote ) is received. Timeout: 1..100 – 1 second ( 1 ) to 100 seconds ( 100 ) in 1-second resolution 101..200 – 1 minute ( 101 ) to 100 minutes ( 200 ) 1-minute resolution 201..209 – 1 hour ( 201 ) to 9 hours ( 209 ) in 1-hour resolution Notice – during the day, this mode cannot be ended remotely due to motion events not being transmitted – only via local motion sensor if enabled.
255 LED is switched off for TIME ( cfg 1 ). It does not wait for a motion event and works normally via current motion evaluation.

Parameter 12: On behaviour time over ( timeout )

Time limit to stop waiting for motion after timeout of ON_BEHAVIOUR or OFF_ON_ BEHAVIOUR ( 0-209 ) to prevent staying ON forever when there is no motion.
Size: 2 Byte, Default Value: 204

Setting Description
0 No additional waiting for motion.
1 - 209 1..100 – 1 second ( 1 ) to 100 seconds ( 100 ) in 1-second resolution 101..200 – 1 minute ( 101 ) to 100 minutes ( 200 ) in 1-minute resolution 201..209 – 1 hour ( 201 ) to 9 hours ( 209 ) in 1-hour resolution
255 Never stop waiting for motion.

Parameter 13: Sequence On-Off behaviour ( timeout )

Behaviour after a rapid sequence of BASIC ON and BASIC OFF commands. The intention is to use a much longer timeout value than the time after a single ON command which should then be followed by a short timeout value.
Size: 2 Byte, Default Value: 204

Setting Description
0 LED is switched off and remains so until any new motion event ( local or remote ) is received.
1 - 209 LED is switched off and remains so until after a specified timeout once a new motion event ( local or remote ) is received. Timeout: 1..100 – 1 second ( 1 ) to 100 seconds ( 100 ) in 1-second resolution 101..200 – 1 minute ( 101 ) to 100 minutes ( 200 ) 1-minute resolution 201..209 – 1 hour ( 201 ) to 9 hours ( 209 ) in 1-hour resolution
255 Device ignores ON - OFF sequence and uses OFF behavior

Parameter 14: Sequence Off-On behaviour ( timeout )

Behaviour after a rapid sequence of BASIC OFF and BASIC ON commands. The intention is to use a much longer timeout value than the time after a single OFF command which should then be followed by a short timeout value.
Size: 2 Byte, Default Value: 204

Setting Description
0 LED is switched on and remains so until any new motion event ( local or remote ) is received. It then works normally via current motion evaluation.
1 - 209 LED is switched off and remains so until after a specified timeout once a new motion event ( local or remote ) is received. Timeout: 1..100 – 1 second ( 1 ) to 100 seconds ( 100 ) in 1-second resolution 101..200 – 1 minute ( 101 ) to 100 minutes ( 200 ) 1-minute resolution 201..209 – 1 hour ( 201 ) to 9 hours ( 209 ) in 1-hour resolution
255 Device ignores OFF - ON sequence and uses ON behaviour.

Parameter 15: Sequence Off-On behaviour ( timeout )


Size: 1 Byte, Default Value: 1

Setting Description
10 - 50 Time in 100ms

Parameter 16: Motion Off behaviour ( timeout )

Motion disable timeout after BASIC SET to motion endpoint when the internal motion sensor is not used for evaluating the behaviour of the LED and groups 2 and 3. Events are, however, still transmitted to the Lifeline, and the device can be controlled via remote motion sensors.
Size: 2 Byte, Default Value: 0

Setting Description
0 BASIC SET to Motion sensor endpoint ignored, BASIC to root is mapped to LED endpoint, motion sensor still enabled
1 - 209 Internal motion sensor is disabled for specified timeout after BASIC SET 0x00 to Motion sensor endpoint. BASIC to root is mapped to Motion sensor endpoint. ( SPIR ) Timeout: 1..100 – 1 second ( 1 ) to 100 seconds ( 100 ) in 1-second resolution 101..200 – 1 minute ( 101 ) to 100 minutes ( 200 ) in 1-minute resolution 201..209 – 1 hour ( 201 ) to 9 hours ( 209 ) in 1-hour resolution
255 BASIC SET to Motion sensor endpoint ignored, BASIC to root is mapped to LED endpoint, motion sensor still disabled

Parameter 17: Toggle button behaviour

Dim increase ( bit 0 ):- long press of button does dim decreasing ( 0 = default )- long press of button does dim increasing ( 1 )

Scene switch ( bit 1 ):- short press of button does toggle – on/off ( 0 = default )- short press of button does scene switch ( 1 )

Standalone behaviour ( bit 2 ):- using legacy sensor deactivity after button press ( 0 = default )- using cfg 10-14 sensor deactivity after button press ( 1 )

Network behaviour ( bit 3 ):- using legacy sensor deactivity after button press ( 0 )- using cfg 10-14 sensor deactivity after button press ( 1 = default )

Dim disable ( bit 4 ):- dim events ( long press ) are used ( 0 = default )- dim events ( long press ) are ignored ( 1 )

legacy sensor deactivity behaviour does this:- Pressing push button when LED is OFF: LED will switch on as long as there is movement and the delay time runs of- Pressing push button when LED is ON: LED will switch off as long as there is movement ans the delay time runs of ( invers logic ).

cfg 10-14 sensor deactivity behaviour uses behaviour specified in parameters 10-14 ( the same behaviour as pressing of external switch using BASIC ON/OFF functions )

Size: 1 Byte, Default Value: 8

Setting Description
1 Dim increase
2 Scene switch
4 Standalone behaviour
8 Network behaviour
16 Dim disable

Parameter 18: Toggle button Scene 1-4

Parameters 18 specifies scene numbers ( from 1 to number ) to be switched by toggle button.
Size: 1 Byte, Default Value: 1

Setting Description
0 menas – do not useany.
1 - 127 Scene ID

Parameter 19: Toggle button inactivity time in legacy mode ( timeout )

In legacy button mode function this timeout is used to cancel motion sensor inactivity mode after motion end ( both for on and off state of LED ).
Size: 2 Byte, Default Value: 103

Setting Description

Technical Data

Dimensions 55 x 55 x 57 mm
Weight 140 gr
Hardware Platform ZM5101
EAN 4007841035402
IP Class IP 20
Voltage 230
Firmware Version 01.80
Z-Wave Version 05.03
Certification ID ZC10-18076193
Z-Wave Product Id 0x0271.0x0002.0x19fb
Frequency Europe - 868,4 Mhz
Maximum transmission power 5 mW

Supported Command Classes

  • Basic
  • Application Status
  • Switch Binary
  • Sensor Multilevel
  • Association Grp Info
  • Device Reset Locally
  • Central Scene
  • Zwaveplus Info
  • Multi Channel
  • Supervision
  • Configuration
  • Alarm
  • Manufacturer Specific
  • Powerlevel
  • Firmware Update Md
  • Association
  • Version
  • Multi Channel Association
  • Security
  • Switch Multilevel
  • Scene Activation
  • Transport Service
  • Security 2

Controlled Command Classes

  • Switch Multilevel
  • Scene Activation
  • Transport Service
  • Security 2

Explanation of Z-Wave specific terms

  • Controller — is a Z-Wave device with capabilities to manage the network. Controllers are typically Gateways,Remote Controls or battery operated wall controllers.
  • Slave — is a Z-Wave device without capabilities to manage the network. Slaves can be sensors, actuators and even remote controls.
  • Primary Controller — is the central organizer of the network. It must be a controller. There can be only one primary controller in a Z-Wave network.
  • Inclusion — is the process of adding new Z-Wave devices into a network.
  • Exclusion — is the process of removing Z-Wave devices from the network.
  • Association — is a control relationship between a controlling device and a controlled device.
  • Wakeup Notification — is a special wireless message issued by a Z-Wave device to announces that is able to communicate.
  • Node Information Frame — is a special wireless message issued by a Z-Wave device to announce its capabilities and functions.