Quickstart

This is a secure Z-Wave Device for XXXQFrequencyName. To run this device please connect it to your mains power supply. To add this device to your network execute the following action:

Press the button three times in rapid succession to put the sensor into inclusion mode.

Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

Product Description

Infrared motion detector with orientation light and Z-Wave interface for indoor power sockets.

Movement triggers lights, alarms and many other devices. For your convenience, safety and peace of mind. The integrated pyroelectric infrared detector senses the invisible heat radiated from moving objects (people, animals, etc.). The heat detected in this way is converted electronically into a signal that switches ON the interconnected load. Heat is not detected through obstacles, such as walls or panes of glass, and will therefore not activate the light. The infrared sensor can be used for switching light ON and OFF automatically. The unit is not suitable for burglar alarm systems as it is not tamperproof in the manner prescribed for such systems. The button activates and deactivates the functions programmed via the Smart Friends app. The orientation light can be switched ON and OFF via the sensor or the button on the MotionSwitch LED Z-Wave. The relevant setting can be programmed via the Smart Friends app. This device can be integrated into the Smart Friends system or any other Z-Wave network. Z-Wave is a wireless standard for interconnecting Z-Wave devices. The power-socket sensor can be used for wireless-based building automation.

Installation

Fit sensor into the power socket so that it is aimed in the required direction.

Product Usage

A = MotionSwitch LED

B = Button

C = Sensor

D = Orientation light

Range:

Factory settings

Twilight level: 2000 lux

Time setting: 3 minutes

The motion detector will also work without being integrated into a Z-Wave network. In this case, the time setting is permanently set to 3 minutes. In this setting, the integrated LED light or a directly connected Z-Wave actuator will be activated. After the 40-second calibration phase, the motion detector is activated for sensor mode. The motion detector can now be integrated into the Z-Wave network. The settings can be made via Z-Wave network.

Twilight setting

The twilight level can be infinitely varied in the range from 2 to 2000 lux via the Smart Friends app.
Note: To adjust the detection zone in daylight, the control dial must be set to 2000 lux = daylight operation.

Reset to factory default	To set the sensor to "Reset", press the button three times in rapid succession and then press it once for several seconds.
Inclusion	Press the button three times in rapid succession to put the sensor into inclusion mode.
Exclusion	To put the sensor into exclusion mode, press the button three times in rapid succession.
NIF	XXXNIF
Wakeup	XXXWakeupDescription
Protection	XXXProtection
FirmwareUpdate	XXXFirmwareUpdate
SetAssociation	XXXSetAssociation

Association Groups:

Group Number	Maximum Nodes	Description
1	1	Lifeline
2	16	On/Off control
3	16	Notification Report
4	16	Ambient light
5	16	Button on/off
6	16	Button scene
7	16	Button dim

Configuration Parameters

Parameter 1: Duration time

Duration of light after motion detection.
Size: 2 Byte, Default Value: 180

Setting Description
5 - 900 Time in s

Setting	Description
5 - 900	Time in s

Parameter 2: Light threshold

Size: 2 Byte, Default Value: 100

Setting Description
0 Run Learn ambient light sequence.

2 - 2000 Threshold in lx

Setting	Description
0	Run Learn ambient light sequence.
2 - 2000	Threshold in lx

Parameter 5: Motion Radar Sensitivity

Size: 1 Byte, Default Value: 100

Setting Description
2 - 100 in %

Setting	Description
2 - 100	in %

Parameter 6: Brightness measuring interval

Size: 1 Byte, Default Value: 0

Setting Description
0 Function is off.

5 - 120 in min.

Setting	Description
0	Function is off.
5 - 120	in min.

Parameter 8: Use external Ambient Light Value:

When GLOBAL_LIGHT mode is ON – device overrides its own light sensor values and uses Light report values from any Z-Wave light sensor instead – this has to be configured appropriately to send light automatically.If the last remote light level value is older than 30 minutes, the internal light value is used again until the next external value is received.
Size: 1 Byte, Default Value: 1

Setting Description
0 Disable

1 Enable

Setting	Description
0	Disable
1	Enable

Parameter 9: Disable local control

Stupid mode ( bit 2 = 1 ):- has higher priority then slave mode.- LED is permanently on ( for simple power wall switch controlling ).

Slave mode ( bit 0 = 1 ):- only if included in Z-Wave network- useful for controlling via third-party sensor- LED is directly controlled via Z-Wave, internal sensors are not used for controlling it Central unit checking ( bit 1 = 1 ): ( useful especially for controlling via gateway )

When slave bit is 0: - device signalises fail of lifeline connection ( if this bit is zero, fail of lifeline connection is not signalised )When slave bit is 1: - device checks presence of Z-Wave device in lifeline group ( gateway ). If it is not present for 2 minutes ( testing repeatedly every 30 seconds ) device switches to normal mode in the same way as after the end of local disabled mode(ON_BEHAVIOUR)- the device checks every 1 minute for recovery of Lifeline connection.- if no lifeline specified - it works in normal mode

Be careful with this option, device stops using its own motion sensor in Slave and Stupid mode.
Size: 2 Byte, Default Value: 1

Setting Description
0 Slave mode

1 Central unit checking in slave mode

2 Stupid mode

Setting	Description
0	Slave mode
1	Central unit checking in slave mode
2	Stupid mode

Parameter 10: Off behaviour ( timeout )

Behaviour after BASIC OFF ( and similar commands ). If a transition ( even with zero change ) with a non-default duration is to be processed, the transition cannot be interrupted by any motion event in any motion event in any case.
Size: 2 Byte, Default Value: 10

Setting Description
0 LED is switched off and remains so until any new motion event ( local or remote ) is received.

1 - 209 LED is switched off and remains so until after a specified timeout once a new motion event ( local or remote ) is received. Timeout: 1..100 – 1 second ( 1 ) to 100 seconds ( 100 ) in 1-second resolution 101..200 – 1 minute ( 101 ) to 100 minutes ( 200 ) 1-minute resolution 201..209 – 1 hour ( 201 ) to 9 hours ( 209 ) in 1-hour resolution

255 LED is switched off for TIME ( cfg 1 ). It does not wait for a motion event and works normally via current motion evaluation.

Setting	Description
0	LED is switched off and remains so until any new motion event ( local or remote ) is received.
1 - 209	LED is switched off and remains so until after a specified timeout once a new motion event ( local or remote ) is received. Timeout: 1..100 – 1 second ( 1 ) to 100 seconds ( 100 ) in 1-second resolution 101..200 – 1 minute ( 101 ) to 100 minutes ( 200 ) 1-minute resolution 201..209 – 1 hour ( 201 ) to 9 hours ( 209 ) in 1-hour resolution
255	LED is switched off for TIME ( cfg 1 ). It does not wait for a motion event and works normally via current motion evaluation.

Parameter 11: On behaviour ( timeout )

Behaviour after BASIC ON ( and similar commands ). If a transition ( even with zero change ) with a non-default duration is to be processed, the transition cannot be interrupted by any motion event in any case.
Size: 2 Byte, Default Value: 255

Setting Description
0 LED is switched on and remains so until any new motion event ( local or remote ) is received. It then works normally via current motion evaluation. Notice – during the day, this mode cannot be ended remotely due to motion events not being transmitted – only via local motion sensor if enabled.

1 - 209 LED is switched off and remains so until after a specified timeout once a new motion event ( local or remote ) is received. Timeout: 1..100 – 1 second ( 1 ) to 100 seconds ( 100 ) in 1-second resolution 101..200 – 1 minute ( 101 ) to 100 minutes ( 200 ) 1-minute resolution 201..209 – 1 hour ( 201 ) to 9 hours ( 209 ) in 1-hour resolution Notice – during the day, this mode cannot be ended remotely due to motion events not being transmitted – only via local motion sensor if enabled.

255 LED is switched off for TIME ( cfg 1 ). It does not wait for a motion event and works normally via current motion evaluation.

Setting	Description
0	LED is switched on and remains so until any new motion event ( local or remote ) is received. It then works normally via current motion evaluation. Notice – during the day, this mode cannot be ended remotely due to motion events not being transmitted – only via local motion sensor if enabled.
1 - 209	LED is switched off and remains so until after a specified timeout once a new motion event ( local or remote ) is received. Timeout: 1..100 – 1 second ( 1 ) to 100 seconds ( 100 ) in 1-second resolution 101..200 – 1 minute ( 101 ) to 100 minutes ( 200 ) 1-minute resolution 201..209 – 1 hour ( 201 ) to 9 hours ( 209 ) in 1-hour resolution Notice – during the day, this mode cannot be ended remotely due to motion events not being transmitted – only via local motion sensor if enabled.
255	LED is switched off for TIME ( cfg 1 ). It does not wait for a motion event and works normally via current motion evaluation.

Parameter 12: On behaviour time over ( timeout )

Time limit to stop waiting for motion after timeout of ON_BEHAVIOUR or OFF_ON_ BEHAVIOUR ( 0-209 ) to prevent staying ON forever when there is no motion.
Size: 2 Byte, Default Value: 204

Setting Description
0 No additional waiting for motion.

1 - 209 1..100 – 1 second ( 1 ) to 100 seconds ( 100 ) in 1-second resolution 101..200 – 1 minute ( 101 ) to 100 minutes ( 200 ) in 1-minute resolution 201..209 – 1 hour ( 201 ) to 9 hours ( 209 ) in 1-hour resolution

255 Never stop waiting for motion.

Setting	Description
0	No additional waiting for motion.
1 - 209	1..100 – 1 second ( 1 ) to 100 seconds ( 100 ) in 1-second resolution 101..200 – 1 minute ( 101 ) to 100 minutes ( 200 ) in 1-minute resolution 201..209 – 1 hour ( 201 ) to 9 hours ( 209 ) in 1-hour resolution
255	Never stop waiting for motion.

Parameter 13: Sequence On-Off behaviour ( timeout )

Behaviour after a rapid sequence of BASIC ON and BASIC OFF commands. The intention is to use a much longer timeout value than the time after a single ON command which should then be followed by a short timeout value.
Size: 2 Byte, Default Value: 204

Setting Description
0 LED is switched off and remains so until any new motion event ( local or remote ) is received.

1 - 209 LED is switched off and remains so until after a specified timeout once a new motion event ( local or remote ) is received. Timeout: 1..100 – 1 second ( 1 ) to 100 seconds ( 100 ) in 1-second resolution 101..200 – 1 minute ( 101 ) to 100 minutes ( 200 ) 1-minute resolution 201..209 – 1 hour ( 201 ) to 9 hours ( 209 ) in 1-hour resolution

255 Device ignores ON - OFF sequence and uses OFF behavior

Setting	Description
0	LED is switched off and remains so until any new motion event ( local or remote ) is received.
1 - 209	LED is switched off and remains so until after a specified timeout once a new motion event ( local or remote ) is received. Timeout: 1..100 – 1 second ( 1 ) to 100 seconds ( 100 ) in 1-second resolution 101..200 – 1 minute ( 101 ) to 100 minutes ( 200 ) 1-minute resolution 201..209 – 1 hour ( 201 ) to 9 hours ( 209 ) in 1-hour resolution
255	Device ignores ON - OFF sequence and uses OFF behavior

Parameter 14: Sequence Off-On behaviour ( timeout )

Behaviour after a rapid sequence of BASIC OFF and BASIC ON commands. The intention is to use a much longer timeout value than the time after a single OFF command which should then be followed by a short timeout value.
Size: 2 Byte, Default Value: 204

Setting Description
0 LED is switched on and remains so until any new motion event ( local or remote ) is received. It then works normally via current motion evaluation.

1 - 209 LED is switched off and remains so until after a specified timeout once a new motion event ( local or remote ) is received. Timeout: 1..100 – 1 second ( 1 ) to 100 seconds ( 100 ) in 1-second resolution 101..200 – 1 minute ( 101 ) to 100 minutes ( 200 ) 1-minute resolution 201..209 – 1 hour ( 201 ) to 9 hours ( 209 ) in 1-hour resolution

255 Device ignores OFF - ON sequence and uses ON behaviour.

Setting	Description
0	LED is switched on and remains so until any new motion event ( local or remote ) is received. It then works normally via current motion evaluation.
1 - 209	LED is switched off and remains so until after a specified timeout once a new motion event ( local or remote ) is received. Timeout: 1..100 – 1 second ( 1 ) to 100 seconds ( 100 ) in 1-second resolution 101..200 – 1 minute ( 101 ) to 100 minutes ( 200 ) 1-minute resolution 201..209 – 1 hour ( 201 ) to 9 hours ( 209 ) in 1-hour resolution
255	Device ignores OFF - ON sequence and uses ON behaviour.

Parameter 15: Sequence Off-On behaviour ( timeout )

Size: 1 Byte, Default Value: 1

Setting Description
10 - 50 Time in 100ms

Setting	Description
10 - 50	Time in 100ms

Parameter 16: Motion Off behaviour ( timeout )

Motion disable timeout after BASIC SET to motion endpoint when the internal motion sensor is not used for evaluating the behaviour of the LED and groups 2 and 3. Events are, however, still transmitted to the Lifeline, and the device can be controlled via remote motion sensors.
Size: 2 Byte, Default Value: 0

Setting Description
0 BASIC SET to Motion sensor endpoint ignored, BASIC to root is mapped to LED endpoint, motion sensor still enabled

1 - 209 Internal motion sensor is disabled for specified timeout after BASIC SET 0x00 to Motion sensor endpoint. BASIC to root is mapped to Motion sensor endpoint. ( SPIR ) Timeout: 1..100 – 1 second ( 1 ) to 100 seconds ( 100 ) in 1-second resolution 101..200 – 1 minute ( 101 ) to 100 minutes ( 200 ) in 1-minute resolution 201..209 – 1 hour ( 201 ) to 9 hours ( 209 ) in 1-hour resolution

255 BASIC SET to Motion sensor endpoint ignored, BASIC to root is mapped to LED endpoint, motion sensor still disabled

Setting	Description
0	BASIC SET to Motion sensor endpoint ignored, BASIC to root is mapped to LED endpoint, motion sensor still enabled
1 - 209	Internal motion sensor is disabled for specified timeout after BASIC SET 0x00 to Motion sensor endpoint. BASIC to root is mapped to Motion sensor endpoint. ( SPIR ) Timeout: 1..100 – 1 second ( 1 ) to 100 seconds ( 100 ) in 1-second resolution 101..200 – 1 minute ( 101 ) to 100 minutes ( 200 ) in 1-minute resolution 201..209 – 1 hour ( 201 ) to 9 hours ( 209 ) in 1-hour resolution
255	BASIC SET to Motion sensor endpoint ignored, BASIC to root is mapped to LED endpoint, motion sensor still disabled

Parameter 17: Toggle button behaviour

Dim increase ( bit 0 ):- long press of button does dim decreasing ( 0 = default )- long press of button does dim increasing ( 1 )

Scene switch ( bit 1 ):- short press of button does toggle – on/off ( 0 = default )- short press of button does scene switch ( 1 )

Standalone behaviour ( bit 2 ):- using legacy sensor deactivity after button press ( 0 = default )- using cfg 10-14 sensor deactivity after button press ( 1 )

Network behaviour ( bit 3 ):- using legacy sensor deactivity after button press ( 0 )- using cfg 10-14 sensor deactivity after button press ( 1 = default )

Dim disable ( bit 4 ):- dim events ( long press ) are used ( 0 = default )- dim events ( long press ) are ignored ( 1 )

legacy sensor deactivity behaviour does this:- Pressing push button when LED is OFF: LED will switch on as long as there is movement and the delay time runs of- Pressing push button when LED is ON: LED will switch off as long as there is movement ans the delay time runs of ( invers logic ).

cfg 10-14 sensor deactivity behaviour uses behaviour specified in parameters 10-14 ( the same behaviour as pressing of external switch using BASIC ON/OFF functions )
Size: 1 Byte, Default Value: 8

Setting Description
1 Dim increase

2 Scene switch

4 Standalone behaviour

8 Network behaviour

16 Dim disable

Setting	Description
1	Dim increase
2	Scene switch
4	Standalone behaviour
8	Network behaviour
16	Dim disable

Parameter 18: Toggle button Scene 1-4

Parameters 18 specifies scene numbers ( from 1 to number ) to be switched by toggle button.
Size: 1 Byte, Default Value: 1

Setting Description
0 menas – do not useany.

1 - 127 Scene ID

Setting	Description
0	menas – do not useany.
1 - 127	Scene ID

Parameter 19: Toggle button inactivity time in legacy mode ( timeout )

In legacy button mode function this timeout is used to cancel motion sensor inactivity mode after motion end ( both for on and off state of LED ).
Size: 2 Byte, Default Value: 103

Setting Description

Technical Data

Dimensions	55 x 55 x 57 mm
Weight	140 gr
Hardware Platform	ZM5101
EAN	4007841035402
IP Class	IP 20
Voltage	230
Firmware Version	01.80
Z-Wave Version	05.03
Certification ID	ZC10-18076193
Z-Wave Product Id	0x0271.0x0002.0x19fb
Frequency	Europe - 868,4 Mhz
Maximum transmission power	5 mW

Steinel

STEINEL MotionSwitch LED

SKU: STEEMSWITCH