TKB Home

Digitel Heating Thermostat

SKU: TKBETZ1036

Quickstart

This is a Z-Wave Device for Europe. To run this device please connect it to your mains power supply. To add this device to your network execute the following action:
When switch off , tap “Manual” continuously three times in two seconds , “wireless” start to fliker. “wireless” display or vanish after add device successfully.

Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

What is Z-Wave?

Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.

Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.

This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.

If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.

For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.

Product Description

Heating thermostat with LCD Screen, adopt z-wave technology to realize remote and manual control. The thermostat is recommended for the control of electric heating device or on/off valve actuator used in hydronic heating .

Prepare for Installation / Reset

Please read the user manual before installing the product.

In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.

Safety Warning for Mains Powered Devices

ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.

Installation

1. Release the front cover by inserting a screwdriver into bottom crack.
2. To pry out the snaps from four directions.

3. After connecting wires, mounting the backing plate in the wall box by screwdriver.
4. Mounting the thermostat on the backing plate.

5. Remount the cover and frame

Connection Plan

Inclusion/Exclusion

On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.

Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.

Inclusion

When switch off , tap “Manual” continuously three times in two seconds , “wireless” start to fliker. “wireless” display or vanish after add device successfully.

Exclusion

When switch off , tap “Manual” continuously three times in two seconds , “wireless” start to fliker. “wireless” display or vanish after delete device successfully.

Product Usage

Manual:

When switch off , tap “Manual” continuously three times in two seconds , “wireless” start to fliker. “wireless” display or vanish after add or delete device successfully.
Press "Manual", chose temperature setting or time setting.
Press the "Manual" key for 3 secounds, LCD screen display room & Floor temperature for switching.

Under in temperature setting mode

Press ▲ key to imcrease the set value and press ▼ key to decrease, every step 0,5°C

Under in time setting mode

Press ▲ or ▼ key to adjust present time.

Under in temperature calibration

Press ▲ or ▼ key for 3 secounds into adjust temperature calibration

Press ▲ or ▼ key to adjust present chacked value. adjustable scale: 9.9°C

After add device successfully, temperature regulation , switch on/off by control terminal equipment.

Sensor Failure:

Please select the right sensor mode when operation it will display the “Err” symbol on screen for sensor failure. Thermostat must be checked till the fault is eliminated.

Attention : The thermostat which connect the electric heating device is apply to full load (3200W) heating cable in 2500m height above sea level, and the rated power of external load should be less than or equal to 80% rated power thermostat when in the 2500m to 4200m height.

Quick trouble shooting

Here are a few hints for network installation if things dont work as expected.

Make sure a device is in factory reset state before including. In doubt exclude before include.
If inclusion still fails, check if both devices use the same frequency.
Remove all dead devices from associations. Otherwise you will see severe delays.
Never use sleeping battery devices without a central controller.
Dont poll FLIRS devices.
Make sure to have enough mains powered device to benefit from the meshing

Association - one device controls an other device

Z-Wave devices control other Z-Wave devices. The relationship between one device controlling another device is called association. In order to control a different device, the controlling device needs to maintain a list of devices that will receive controlling commands. These lists are called association groups and they are always related to certain events (e.g. button pressed, sensor triggers, ...). In case the event happens all devices stored in the respective association group will receive the same wireless command wireless command, typically a 'Basic Set' Command.

Association Groups:

Group Number	Maximum Nodes	Description
1	1	Lifeline

Technical Data

Dimensions	0.0590000x0.0750000x0.1020000 mm
Weight	182 gr
Hardware Platform	ZM5202
EAN	6959174471724
IP Class	IP 20
Voltage	230V
Load	16A
Firmware Version	00.12
Z-Wave Version	04.26
Certification ID	ZC10-16010014
Z-Wave Product Id	0x0118.0x0201.0x0501
Frequency	Europe - 868,4 Mhz
Maximum transmission power	5 mW

Supported Command Classes

Basic

Sensor Multilevel

Thermostat Mode

Thermostat Operating State

Thermostat Setpoint

Association Grp Info

Device Reset Locally

Zwaveplus Info

Configuration

Manufacturer Specific

Powerlevel

Firmware Update Md

Clock

Association

Version

Explanation of Z-Wave specific terms

Controller — is a Z-Wave device with capabilities to manage the network. Controllers are typically Gateways,Remote Controls or battery operated wall controllers.
Slave — is a Z-Wave device without capabilities to manage the network. Slaves can be sensors, actuators and even remote controls.
Primary Controller — is the central organizer of the network. It must be a controller. There can be only one primary controller in a Z-Wave network.
Inclusion — is the process of adding new Z-Wave devices into a network.
Exclusion — is the process of removing Z-Wave devices from the network.
Association — is a control relationship between a controlling device and a controlled device.
Wakeup Notification — is a special wireless message issued by a Z-Wave device to announces that is able to communicate.
Node Information Frame — is a special wireless message issued by a Z-Wave device to announce its capabilities and functions.