This is a
To include the device into the network, turn the controller into the inclusion mode and then press the upper or lower part of the paddle of the device. The device is now ready to work.
The TZ65-D dual wall dimmer is switching attached loads and is controlled either by the local switching paddle or remotely via the Z-Wave wireless protocol. It is included and controlled in a Z-Wave network by a remote control, a wireless control centre or any other kind of Z-Wave controller including a PC-software. Beside the local switch the unit can control other Z-Wave units remotely in up to three additional Z-Wave groups, which are associated with this device. Tipping one time or two times the switching paddle performs the control. The left paddle controls the local load while the right paddle remotely controls Z-Wave associated devices only. The association of further Z-Wave devices needs to be done by a Z-Wave controller. The unit is powered by 230V and needs a pattress box with 230 V power wires for installation.
The TZ65-D wall mounted dimmer needs a pattress box with 230 V power wires for installation. It does not fit into European wall boxes with 60 mm diameter.
The actuator can be set to control other Z-Wave devices and is operated by the local switching paddles or wirelessly using Z-Wave commands. The left paddle controls the local load while the right paddle remotely controls Z-Wave associated devices only. If the insert is mounted correctly pushing the upper part of the left or right paddle will turn ON the load. Pushing the lower part of the left or right paddle will turn OFF the electric load. Pressing and holding the switch will allow dimming and brightening of Z-Wave dimmers if associated.
Reset to factory default | XXXResetDescription |
Inclusion | The device is included and excluded by a single click on the switch when the controller is in inclusion resp. exclusion mode. |
Exclusion | The device is included and excluded by a single click on the switch when the controller is in inclusion resp. exclusion mode. |
NIF | XXXNIF |
Wakeup | XXXWakeupDescription |
Protection | XXXProtection |
FirmwareUpdate | XXXFirmwareUpdate |
SetAssociation | XXXSetAssociation |
Group Number | Maximum Nodes | Description |
---|---|---|
4 | 5 | every switching command |
3 | 5 | Tap right paddle twice |
2 | 5 | Tap right paddle once |
1 | 5 | Tap left paddle once |
defines if the start level bit shall be ignores when transmitting a dim command to a dimmer Size: 1 Byte, Default Value: 01
Setting | Description |
---|---|
00 | ignore |
01 | dont ignore |
defines if the Association group 4 shall be active or not Size: 1 Byte, Default Value: 00
Setting | Description |
---|---|
00 | yes |
01 | no |
Activates Night Light Size: 1 Byte, Default Value: 00
Setting | Description |
---|---|
00 | LED blinks on activity |
01 | Night Light active |
Inverts Switching (on is upper part) Size: 1 Byte, Default Value: 00
Setting | Description |
---|---|
00 | dont invert |
01 | invert |
defines the behavior of the LED when transmitting data Size: 1 Byte, Default Value: 00
Setting | Description |
---|---|
00 | no flicker |
01 | flicker all time of data transmission |
02 | flicker for one second only |
The device can operate shade control devices via Group 3 if this parameter is activated Size: 1 Byte, Default Value: 00
Setting | Description |
---|---|
00 | inactive |
01 | active |
The device can operate shade control devices via Group 2 if this parameter is activated Size: 1 Byte, Default Value: 00
Setting | Description |
---|---|
00 | inactive |
01 | active |
defines the poll interfal for group 2 if polling is activated Size: 1 Byte, Default Value: 02
Setting | Description |
---|
defines if Group 2 shall be polled or not Size: 1 Byte, Default Value: 01
Setting | Description |
---|---|
00 | dont poll |
01 | poll |
Dimensions | 0.0840000x0.0840000x0.0460000 mm |
Weight | 105 gr |
EAN | 6959174465006 |
Device Type | Light Dimmer Switch |
Generic Device Class | Multilevel Switch |
Specific Device Class | Routing Multilevel Switch |
Firmware Version | 01.03 |
Z-Wave Version | 03.28 |
Certification ID | ZC08-12110001 |
Z-Wave Product Id | 0118.0808.0808 |
Frequency | Europe - 868,4 Mhz |
Maximum transmission power | 5 mW |