Vision Security
Door Contact
SKU: VISEZD2102-5
Quickstart
This is a
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
The ZD2102-5 Door and Window sensor is used in any Z-Wave network to detect the opening or closing of a door or window. Special Design can fit most of door/window frame. The primary sensing element is a magnetic reed switch, the ZD2102-5 is supplied with the sensor, sensor mounting bracket and the trigger magnet. An additional set of sensor inputs are provided through a 2 position screw terminal and can be used to expand the sensor capability to multiple inputs. The ZD2102-5 is powered by a single CR123A Lithium Battery (supplied with unit, battery life is more than 5 years) and is intended for indoor use only. The ZD2102-5 features tamper proof switch, low battery warning and can be firmware updated over the air.
| Reset to factory default | Factory Default Reset: Trigger the rear cover switch to send the Alarm Report and trigger the reed switch (close & open) 5 times in 10 seconds, ZD2102-5 will send the “Device Reset Locally Notification†command and reset to the factory default condition. |
| Inclusion | For “Inclusion†(adding to) a network: Put the Z-Wave™ network controller into “inclusion†mode following its instructions. To add the ZD2102-5 to your controller press the program switch of ZD2102-5 to send the Node Information Frame (NIF). After sending NIF, the network controller will send the auto inclusion request; otherwise, ZD2102-5 will go to sleep after 15 seconds. |
| Exclusion | For “Exclusion†(removing from) a network: Put the Z-Wave™ network controller into “exclusion†mode, following its instructions. To delete the ZD2102-5 from your controller press the program switch of ZD2102-5 for at least 1 second to be excluded. Note: All user and network settings will be cleared and the device reset to factory setting defaults when the device is excluded. |
| NIF | XXXNIF |
| Wakeup | The ZD2102-5 is forced awake by opening the rear cover, the red LED will stay on and the 2102-5 will stay awake for 10 seconds. The ZD2102-5 will send “Wake Up Notificationâ€. If ZD2102-5 receives a “Wake Up No More Information†command then the red LED will go off and it will go to sleep. Auto Wake Up: The wakeup interval is user settable from 10 minutes to 1 week using COMMAND_CLASS_WAKE_UP, Interval increment is 3 minutes. |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | LifeLine association for central static controller COMMAND_CLASS_DEVICE_RESET_LOCALLY, DEVICE_RESET_LOCALLY_NOTIFICATION, COMMAND_CLASS_BATTERY, BATTERY_REPORT, COMMAND_CLASS_NOTIFICATION_V4, NOTIFICATION_REPORT_V4 |
Configuration Parameters
Parameter 1: Enable/disable external switch.
To enable or disable external switch function. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 255 | 0x00 is disable external switch , 0xFF is enable external switch. |
Technical Data
| Dimensions | 87x25x21 mm |
| Weight | 24 gr |
| Hardware Platform | ZM5202 |
| EAN | 0019962005701 |
| Device Type | Notification Sensor |
| Network Operation | Reporting Sleeping Slave |
| Z-Wave Version | 6.51.01 |
| Certification ID | ZC10-14040002 |
| Z-Wave Product Id | 0x0109.0x2001.0x0105 |
| Frequency | Europe - 868,4 Mhz |
| Maximum transmission power | 5 mW |