Quickstart

This is a Binary Power Switch for XXXQFrequencyName. To run this device please connect it to your mains power supply.

S WiDom Universal Double Switch is designed for installation in flush mounting boxes, close to the loads to be controlled. A single click on the Z-Wave button will confirm Inclusion and three clicks will confirm Exclusion.

Please read carefully the enclosed user manual before installation of the radio-actuator, in order to ensure an error-free functioning.

ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with 230 Volt mains power.

WiDom Universal Double Switch Activation

1) Ensure that the main power switch is set in the OFF position

2) Connect the device following the diagrams provided

3) Include the device into the Z-Wave network

4) Shut the electrical box containing the device

5) Turn the main power switch back on

Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

Product Description

Universal Double Switch is an ON/OFF control device designed to independently control two separate loads, suited for use as both a local and remote switch. Each of its two channels features an integrated consumption measurement device. The Universal Double Switch also boasts the lowest energy consumption on the market.

Installation

INFO: WiDom Universal Double Switch is designed for installation in flush mounting boxes, close to the loads to be controlled.

WARNING: WiDom Universal Double Switch must be installed by electricians qualified to operate on electrical systems in compliance with safety requirements set out by current regulations.

DANGER: WiDom Universal Double Switch must be connected to 230V AC voltage mains supplies; please ensure that the general switch is in the OFF position prior to carrying out any operation.

DANGER: Any operation requiring the use of service button (B) must only be carried out during the installation phase and must be considered as a service procedure to be performed by qualified personnel. This operation must be carried out by adopting all necessary precautions to operate on areas with a single level of isolation.

WARNING: Do not connect loads exceeding the maximum power load permitted by the relay contacts.

WARNING: All connections must be performed according to the electrical diagrams provided.

WARNING: WiDom Universal Double Switch must be installed in norm-compliant systems suitably protected from overloads and short circuits.

TIP: The antenna must not be shortened, removed or modified. To ensure maximum efficiency, it must be installed as shown. Large size metal equipment near the antenna can negatively affect reception. Each WiDom device is a node in a mesh network. If there are metal obstacles, the obstacle can often be overcome with a further triangulation node.

L) Phase connection terminal

N) Neutral connection terminal

I1) Neutral signal to activate the output 1

I2) Neutral signal to activate the output 2

O1) Phase Output 1 referred to Neutral

O2) Phase Output 2 referred to Neutral

Product Usage

If the device was successfully included it will apear in your SmartHome Software.

WiDom Universal Double Switch can control other devices such as relays or dimmers.

Reset to factory default	XXXResetDescription
Inclusion	1 click on the Z-Wave Button to confirm inclusion of the device. 3 clicks on the Z-Wave Button to confirm exclusion of the device. 6 clicks on the Z-Wave Button to confirm reset to factory settings.
Exclusion	1 click on the Z-Wave Button to confirm inclusion of the device. 3 clicks on the Z-Wave Button to confirm exclusion of the device. 6 clicks on the Z-Wave Button to confirm reset to factory settings.
NIF	Single press the Z-Wave Button to send out a Node Information Frame.
Wakeup	XXXWakeupDescription
Protection	XXXProtection
FirmwareUpdate	XXXFirmwareUpdate
SetAssociation	XXXSetAssociation

Association Groups:

Group Number	Maximum Nodes	Description
1	8	LifeLine: Devices to receive notifications on: status changes; instantaneous power level; device local reset
2	8	On/Off control (Switch 1)
3	8	Dimming control (Switch 1)
4	8	On/Off control (Switch 2)
5	8	Dimming control (Switch 2)

Configuration Parameters

Parameter 1: Outputs Status 1 Click

Defines the status of the output O1/O2 when the switch connected to I1/I2 receives 1 Click.
Size: 1 Byte, Default Value: 1

Setting Description
1 TOGGLE

2 ON: If the initial status is OFF the system switches to ON; conversely, it maintains its status (ON).

3 OFF: If the initial status is ON the system switches to OFF; conversely, it maintains its status (OFF).

4 IGNORE: The device maintains the initial status

Setting	Description
1	TOGGLE
2	ON: If the initial status is OFF the system switches to ON; conversely, it maintains its status (ON).
3	OFF: If the initial status is ON the system switches to OFF; conversely, it maintains its status (OFF).
4	IGNORE: The device maintains the initial status

Parameter 2: Output Status 2 Clicks

Defines the status of the output O1/O2 when the switch connected to I1/I2 receives 2 Click.
Size: 1 Byte, Default Value: 1

Setting	Description
1	TOGGLE
2	ON: If the initial status is OFF the system switches to ON; conversely, it maintains its status (ON).
3	OFF: If the initial status is ON the system switches to OFF; conversely, it maintains its status (OFF).
4	IGNORE: The device maintains the initial status

Parameter 3: Type of outputs

Defines if the outputs are controlled individually, as a traditional device with two channels, or if its behaviour simulates a single pole double throw relay.
Size: 1 Byte, Default Value: 0

Setting Description
0 SINGLE CHANNELS: Channel 1 and Channel 2 are controlled individually

1 - 127 SINGLE POLE DOUBLE THROW RELAY: The two channels are in opposite status. If the Channel 1 is close the Channel 2 is open, if the Channel 1 is open the Channel 2 is close. The value of the parameter defines the closing delay of the relay in tenth of seconds

Setting	Description
0	SINGLE CHANNELS: Channel 1 and Channel 2 are controlled individually
1 - 127	SINGLE POLE DOUBLE THROW RELAY: The two channels are in opposite status. If the Channel 1 is close the Channel 2 is open, if the Channel 1 is open the Channel 2 is close. The value of the parameter defines the closing delay of the relay in tenth of seconds

Parameter 4: Number of clicks that activate the control of the associated devices

Defines the number of clicks on the Switch 1 or Switch 2 that enable the control of the correspondent associated devices.
Size: 1 Byte, Default Value: 2

Setting Description
1 Associated devices are controlled by 1 Click on the correspondent external switch

2 Associated devices are controlled by 2 Clicks on the correspondent external switch

Setting	Description
1	Associated devices are controlled by 1 Click on the correspondent external switch
2	Associated devices are controlled by 2 Clicks on the correspondent external switch

Parameter 5: Level used to control the devices associated to group 2 and 3

Defines how to control the devices associated to group 2 and 3.
Size: 1 Byte, Default Value: 100

Setting Description
0 The associated devices are switched OFF

255 The associated devices are switched ON

1 - 99 The associated devices (dimmer, roller shutters) are set to the indicated level (only for devices associated to group 3)

100 If the Relay 1 is ON/OFF, the associated devices are ON/OFF

101 If the Relay 1 is ON the associated devices are ON; if it is OFF no action is taken on the associated devices

102 If the Relay 1 is OFF the associated devices are OFF; if it is ON no action is taken on the associated devices

103 If the Relay 1 is ON the associated devices are OFF; if it is OFF no action is taken on the associated devices

104 If the Relay 1 is OFF the associated devices are ON; if it is ON no action is taken on the associated devices

105 If the Relay 1 is ON/OFF, the associated devices are OFF/ON

106 No action is taken on the associated devices

Setting	Description
0	The associated devices are switched OFF
255	The associated devices are switched ON
1 - 99	The associated devices (dimmer, roller shutters) are set to the indicated level (only for devices associated to group 3)
100	If the Relay 1 is ON/OFF, the associated devices are ON/OFF
101	If the Relay 1 is ON the associated devices are ON; if it is OFF no action is taken on the associated devices
102	If the Relay 1 is OFF the associated devices are OFF; if it is ON no action is taken on the associated devices
103	If the Relay 1 is ON the associated devices are OFF; if it is OFF no action is taken on the associated devices
104	If the Relay 1 is OFF the associated devices are ON; if it is ON no action is taken on the associated devices
105	If the Relay 1 is ON/OFF, the associated devices are OFF/ON
106	No action is taken on the associated devices

Parameter 6: Level used to control the devices associated to group 4 and 5

Defines how to control the devices associated to group 4 and 5.
Size: 1 Byte, Default Value: 100

Setting Description
0 The associated devices are switched OFF

255 The associated devices are switched ON

1 - 99 The associated devices (dimmer, roller shutters) are set to the indicated level (only for devices associated to group 5)

100 If the Relay 2 is ON/OFF, the associated devices are ON/OFF

101 If the Relay 2 is ON the associated devices are ON; if it is OFF no action is taken on the associated devices

102 If the Relay 2 is OFF the associated devices are OFF; if it is ON no action is taken on the associated devices

103 If the Relay 2 is ON the associated devices are OFF; if it is OFF no action is taken on the associated devices

104 If the Relay 2 is OFF the associated devices are ON; if it is ON no action is taken on the associated devices

105 If the Relay 2 is ON/OFF, the associated devices are OFF/ON

106 No action is taken on the associated devices

Setting	Description
0	The associated devices are switched OFF
255	The associated devices are switched ON
1 - 99	The associated devices (dimmer, roller shutters) are set to the indicated level (only for devices associated to group 5)
100	If the Relay 2 is ON/OFF, the associated devices are ON/OFF
101	If the Relay 2 is ON the associated devices are ON; if it is OFF no action is taken on the associated devices
102	If the Relay 2 is OFF the associated devices are OFF; if it is ON no action is taken on the associated devices
103	If the Relay 2 is ON the associated devices are OFF; if it is OFF no action is taken on the associated devices
104	If the Relay 2 is OFF the associated devices are ON; if it is ON no action is taken on the associated devices
105	If the Relay 2 is ON/OFF, the associated devices are OFF/ON
106	No action is taken on the associated devices

Parameter 10: Timer to switch ON the Channel 1

Defines the time after which the Channel 1 is switched ON.
Size: 2 Byte, Default Value: 0

Setting Description
0 Timer disabled

1 - 32000 After this time the relay of the Channel 1 is ON

Setting	Description
0	Timer disabled
1 - 32000	After this time the relay of the Channel 1 is ON

Parameter 11: Timer to switch ON the Channel 2

Defines the time after which the Channel 2 is switched ON.
Size: 2 Byte, Default Value: 0

Setting Description
0 Timer disabled

1 - 32000 After this time the relay of the Channel 2 is ON

Setting	Description
0	Timer disabled
1 - 32000	After this time the relay of the Channel 2 is ON

Parameter 12: Timer to switch OFF the Channel 1

Defines the time after which the Channel 1 is switched OFF.
Size: 2 Byte, Default Value: 0

Setting Description
0 Timer disabled

1 - 32000 After this time the relay of the Channel 1 is OFF

Setting	Description
0	Timer disabled
1 - 32000	After this time the relay of the Channel 1 is OFF

Parameter 13: Timer to switch OFF the Channel 2

Defines the time after which the Channel 2 is switched OFF.
Size: 2 Byte, Default Value: 0

Setting Description
0 Timer disabled

1 - 32000 After this time the relay of the Channel 2 is OFF

Setting	Description
0	Timer disabled
1 - 32000	After this time the relay of the Channel 2 is OFF

Parameter 20: Outputs status upon receipt of a Multi-Channel Basic Set command

The two channels can be controlled individually by Z-Wave network. The status of the channels upon receipt of a Multi-Channel Basic Set command is defined by the value set on the parameter.
Size: 1 Byte, Default Value: 1

Setting Description
1 AS RECEIVED

2 IGNORE IF ON

3 IGNORE IF OFF

4 IGNORE

Setting	Description
1	AS RECEIVED
2	IGNORE IF ON
3	IGNORE IF OFF
4	IGNORE

Parameter 21: Outputs status upon receipt of a Basic Set command

The channels of the device can be controlled individually from all other Z-Wave devices that support the multichannel feature. In order to support also the integration with no-multichannel systems, this parameter allows to define if the receipt of a no-multichannel command controls only the Channel 1 or both.
Size: 1 Byte, Default Value: 3

Setting Description
1 The receipt of a Basic Set ON/OFF set the Channel 1 to ON/OFF

3 The receipt of a Basic Set ON/OFF set both the Channel 1 and the Channel 2 to ON/OFF

Setting	Description
1	The receipt of a Basic Set ON/OFF set the Channel 1 to ON/OFF
3	The receipt of a Basic Set ON/OFF set both the Channel 1 and the Channel 2 to ON/OFF

Parameter 60: Start-up status

Defines the status of the device following a restart.
Size: 1 Byte, Default Value: 4

Setting Description
0 Both Relay 1 and Relay 2 OFF

1 Relay 1 ON, Relay 2 OFF

2 Relay 1 OFF, Relay 2 ON

3 Both Relay 1 and Relay 2 ON

4 PREVIOUS STATUS: Status prior to restart

Setting	Description
0	Both Relay 1 and Relay 2 OFF
1	Relay 1 ON, Relay 2 OFF
2	Relay 1 OFF, Relay 2 ON
3	Both Relay 1 and Relay 2 ON
4	PREVIOUS STATUS: Status prior to restart

Parameter 61: Configuration reset

Defines which parameters should be reset to default values.
Size: 1 Byte, Default Value: 4

Setting Description
0 The device is reset to the original factory settings

1 All associations and only the associations are reset

2 The associations are maintained while all other configuration parameters are reset to the original factory settings, except for the specific configuration.

3 The device will be restarted

4 No action is performed

Setting	Description
0	The device is reset to the original factory settings
1	All associations and only the associations are reset
2	The associations are maintained while all other configuration parameters are reset to the original factory settings, except for the specific configuration.
3	The device will be restarted
4	No action is performed

Parameter 62: Type of external switch

Defines the type of external switch connected to the device.
Size: 1 Byte, Default Value: 4

Setting Description
0 The actions on the external switch are ignored. In this mode, the device can only be controlled via the network.

1 The external switch is a normally open button

2 The external switch is a traditional switch

4 After the first single click on the external switch, the system automatically determines the type of external switch used and sets the parameter with the new value accordingly.

Setting	Description
0	The actions on the external switch are ignored. In this mode, the device can only be controlled via the network.
1	The external switch is a normally open button
2	The external switch is a traditional switch
4	After the first single click on the external switch, the system automatically determines the type of external switch used and sets the parameter with the new value accordingly.

Technical Data

Dimensions	0.0370000x0.0370000x0.0170000 mm
Weight	28.2 gr
Hardware Platform	ZM5202
EAN	8059265060047
IP Class	IP 20
Voltage	230 V
Load	10 A
Device Type	On/Off Power Switch
Generic Device Class	Binary Switch
Specific Device Class	Binary Power Switch
Firmware Version	01.28
Z-Wave Version	04.05
Certification ID	ZC10-15115003
Z-Wave Product Id	0x0149.0x1214.0x0504
Frequency	Europe - 868,4 Mhz
Maximum transmission power	5 mW

WiDom

Z-Wave Double Switch

SKU: WIDEWDS