This is a
Pressing any sequence of click on the integrated button
Reset to factory default | 6 consecutive clicks on the integrated button. |
Inclusion | Pressing any sequence of click on the integrated button |
Exclusion | Pressing any sequence of click on the integrated button. |
NIF | XXXNIF |
Wakeup | XXXWakeupDescription |
Protection | XXXProtection |
FirmwareUpdate | XXXFirmwareUpdate |
SetAssociation | XXXSetAssociation |
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 8 | Lifeline |
2 | 8 | Send Basic Set Command |
3 | 8 | Send Basic Set Command |
4 | 8 | Send Basic Set Command |
5 | 8 | Send Basic Set Command |
6 | 8 | Send Basic Set Command |
7 | 8 | Send Basic Set Command |
Define which sequences of clicks control the load connected to both Channel 1 and Channel 2, if parameter No. 2 is set to its default value. Otherwise parameter No.1 sets the clicks sequence only for Channel 1 and parameter No. 2 sets the clicks sequence for Channel 2. Size: 1 Byte, Default Value: 7
Setting | Description |
---|---|
0 | Local Control disabled |
1 | 1 click controls the local load |
2 | 2 clicks control the local load |
4 | 3 clicks control the local load |
7 | The load connected to the Channel 1 can be controlled using 1 click, 2 clicks or 3 clicks |
Define which sequences of click control the load connected to Channel 2 Size: 1 Byte, Default Value: 8
Setting | Description |
---|---|
0 | Local Control disabled |
1 | 1 click controls the local load |
2 | 2 clicks control the local load |
4 | 3 clicks control the local load |
8 | The load connected to the Channel 2 will be controlled with the same number of clicks configured for Channel 1. |
Defines the actions to be carried out on the associated devices in terms of Basic Set. Size: 1 Byte, Default Value: 100
Setting | Description |
---|---|
0 | Off |
1 - 99 | Dimming purpose |
100 | The same value of Channel 1 status |
255 | On |
Defines the actions to be carried out on the associated devices in terms of Basic Set. Size: 1 Byte, Default Value: 100
Setting | Description |
---|---|
0 | Off |
1 - 99 | Dimming purpose |
100 | The same value of Channel 1 status |
255 | On |
Defines the actions to be carried out on the associated devices in terms of Basic Set. Size: 1 Byte, Default Value: 100
Setting | Description |
---|---|
0 | Off |
1 - 99 | Dimming purpose |
100 | The same value of Channel 1 status |
255 | On |
Defines the actions to be carried out on the associated devices in terms of Basic Set. Size: 1 Byte, Default Value: 100
Setting | Description |
---|---|
0 | Off |
1 - 99 | Dimming purpose |
100 | The same value of Channel 1 status |
255 | On |
Defines the actions to be carried out on the associated devices in terms of Basic Set. Size: 1 Byte, Default Value: 100
Setting | Description |
---|---|
0 | Off |
1 - 99 | Dimming purpose |
100 | The same value of Channel 1 status |
255 | On |
Defines the actions to be carried out on the associated devices in terms of Basic Set. Size: 1 Byte, Default Value: 100
Setting | Description |
---|---|
0 | Off |
1 - 99 | Dimming purpose |
100 | The same value of Channel 1 status |
255 | On |
Defines the time after which the Channel 1 is switched OFF. Size: 2 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Timer disabled |
1 - 32000 | Tenths of seconds after which the relay of the Channel 1 is OFF |
Defines the time after which the Channel 2 is switched OFF. Size: 2 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Timer disabled |
1 - 32000 | Tenths of seconds after which the relay of the Channel 2 is OFF |
Defines the time after which the Channel 1 is switched ON. Size: 2 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Timer disabled |
1 - 32000 | Tenths of seconds after which the relay of the Channel 1 is ON |
Defines the time after which the Channel 2 is switched ON. Size: 2 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Timer disabled |
1 - 32000 | Tenths of seconds after which the relay of the Channel 2 is ON |
Defines the behavior of the device Channels when the I1/I2 buttons receive a valid number of clicks (see Parameters No. 1 and No. 2).Note: When to the parameter 40 is given a value different from zero, the associated devices will not be controlled. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | I1 button control Channel 1 and I2 button control Channel 2 |
1 | Both channels can be OFF but they can never be ON simultaneously. |
2 | Channels are toggled in this order: both channels ON, only Channel 1 ON, only Channel 2 ON, both channels OFF. |
Defines the status of the device following a restart. Size: 1 Byte, Default Value: 4
Setting | Description |
---|---|
0 | Both Channel 1 and Channel 2 OFF |
1 | Channel 1 OFF, Channel 2 ON |
2 | Channel 1 ON, Channel 2 OFF |
3 | Both Channel 1 and Channel 2 ON |
4 | Status prior to restart |
Defines the type of external switch connected both to input 1 and input 2, if parameter No. 63 is set in its default value. Otherwise parameter No. 62 defines only the switch connected to the input 1 and parameter No. 63 the switch connected to the input 2. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
0 | The actions on the external switch are ignored. In this mode, the device can only be controlled through the network. |
1 | The external switch is a normally open button |
2 | The external switch is a traditional switch |
Define the switch type connected to the input 2. Size: 1 Byte, Default Value: 3
Setting | Description |
---|---|
0 | The actions on the external switch are ignored. In this mode, the device can only be controlled through the network. |
1 | The external switch is a normally open button |
2 | The external switch is a traditional switch |
3 | The external switch connected to input 2 is equal to the switch connected to the input 1 defined by parameter No. 62. |
Dimensions | 37x37x17 mm mm |
Weight | 26.65 gr |
Hardware Platform | ZM5101 |
EAN | 8059265060078 |
IP Class | IP 20 |
Voltage | 230V |
Load | 10 A |
Device Type | On/Off Power Switch |
Generic Device Class | Binary Switch |
Specific Device Class | Binary Power Switch |
Network Operation | Always On Slave |
Firmware Version | 01.00 |
Z-Wave Version | 06.04 |
Z-Wave Product Id | 0x0149.0x1214.0x0b00 |
Frequency | Europe - 868,4 Mhz |
Maximum transmission power | 5 mW |