Quickstart

This is a secure Relais Switch for Europe. To run this device please connect it to your mains power supply. To add this device to your network execute the following action:
Pressing any sequence of click on the integrated button.



Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

What is Z-Wave?

Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.

Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.

This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.

If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.

For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.

Product Description

WiDom Smart Dry Contact Switch can turn ON and OFF equipments with an independent power supply, such as solenoid valves (e.g. gas, water and irrigation), power operated valves etc. 

WiDom Smart Dry Contact Switch is very easy to install and works with both momentary and toggle switches.

The device is equipped with contact protection technology (Zero Crossing) which reduces the electrical stress on the relay contacts and ensures a longer life. The open / closed switching of the device always occur when the instantaneous value of voltage is 0.

It operates in any Z-Wave network with other Z-Wave/Z-Wave Plus certified devices and controllers from any other manufacturer. As a constantly powered node, WiDom Smart Double Switch will act as repeater regardless of the vendor in order to increase the reliability of the network.

Prepare for Installation / Reset

Please read the user manual before installing the product.

In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.

Reset to factory default

This device also allows to be reset without any involvement of a Z-Wave controller. This procedure should only be used when the primary controller is inoperable.

6 consecutive clicks on the integrated button

Safety Warning for Mains Powered Devices

ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.

Installation

Line (L)- Phase connection terminal
Null (N) - Neutral connection terminal
Dry Contact (1 + 2)- contact relay
Line Signal (LS) -  External Switch Connection
Integrated Button:
1 click to enter in Learn Mode
6 clicks to reset the system to manufacturer‘s settings

Electrical Connections diagram
The device must be supplied by phase and neutral.
Connections must be done following one of the diagrams below: if you need to control a Load connected on a different power supply system you must follow the diagram on the right side.



Inclusion/Exclusion

On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.

Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.

Inclusion

Pressing any sequence of click on the integrated button.

Exclusion

Pressing any sequence of click on the integrated button.

Product Usage

LED status indicator

The system includes an RGB LED that shows the device’s status during installation:

Solid RED: the device is not included in any network
OFF: the device is already associated to a Z-Wave network
Blink GREEN: the device has sent an unsolicited Multilevel Frame to Lifeline group
Blink YELLOW: the device has sent an unsolicited Meter Frame to Lifeline group
Blink VIOLET: the device has sent a command to the association device. The number of blinks is equal to the ID Association group
A sequence of GREEN-BLUE Learn Mode for inclusion
A sequence of RED-BLUE Learn Mode for exclusion

INFO: The Learn Mode status is activated or deactivated by a single click on the integrated button.

TIP: To test if the electrical connections are correct, before the inclusion of the device, while pressing n times the external switch, the RGB LED should flash green for the same amount of times. If it does not, check the wire connections.

Quick trouble shooting

Here are a few hints for network installation if things dont work as expected.

  1. Make sure a device is in factory reset state before including. In doubt exclude before include.
  2. If inclusion still fails, check if both devices use the same frequency.
  3. Remove all dead devices from associations. Otherwise you will see severe delays.
  4. Never use sleeping battery devices without a central controller.
  5. Dont poll FLIRS devices.
  6. Make sure to have enough mains powered device to benefit from the meshing

Association - one device controls an other device

Z-Wave devices control other Z-Wave devices. The relationship between one device controlling another device is called association. In order to control a different device, the controlling device needs to maintain a list of devices that will receive controlling commands. These lists are called association groups and they are always related to certain events (e.g. button pressed, sensor triggers, ...). In case the event happens all devices stored in the respective association group will receive the same wireless command wireless command, typically a 'Basic Set' Command.

Association Groups:

Group Number Maximum Nodes Description
1 8 Lifeline
2 8 1x Click - Basic Set
3 8 2x Click - Basic Set
4 8 3x Click - Basic Set

Configuration Parameters

Z-Wave products are supposed to work out of the box after inclusion, however certain configuration can adapt the function better to user needs or unlock further enhanced features.

IMPORTANT: Controllers may only allow configuring signed values. In order to set values in the range 128 ... 255 the value sent in the application shall be the desired value minus 256. For example: To set a parameter to 200 it may be needed to set a value of 200 minus 256 = minus 56. In case of a two byte value the same logic applies: Values greater than 32768 may needed to be given as negative values too.

Parameter 1: Numbers of clicks on the external switch to control the load

Defines which sequences of clicks control the load.
Size: 1 Byte, Default Value: 7

Setting Description
0 Disabled
1 One Click
2 Two Click
4 Three Click
7 All

Parameter 4: Value used for devices belonging to Group 2 when the external switch receives 1 Click


Size: 1 Byte, Default Value: 100

Setting Description
0 Off
1 - 99 Dimming purpose
100 The same value of dry contact status
255 On

Parameter 5: Value used for devices belonging to Group 3 when the external switch receives 2 Clicks


Size: 1 Byte, Default Value: 100

Setting Description
0 Off
1 - 99 Dimming purpose
100 The same value of dry contact status
255 On

Parameter 6: alue used for devices belonging to Group 4 when external switch receives 3 Clicks


Size: 1 Byte, Default Value: 100

Setting Description
0 Off
1 - 99 Dimming purpose
100 The same value of dry contact status
255 On

Parameter 10: Timer to switch OFF the Relay

Defines the time after which the relay is switched OFF.
Size: 2 Byte, Default Value: 0

Setting Description
0 Timer disabled
1 - 32000 Number of time units (see parameter No.15) after which the dry contact is switched OFF

Parameter 11: Timer to switch ON the Relay

Defines the time after which the relay is switched ON.
Size: 2 Byte, Default Value: 0

Setting Description
0 Timer disabled
1 - 32000 Number of time units (see parameter No.15) after which the dry contact is switched ON

Parameter 15: Timer scale

Defines the time unit used for parameters No.10 and No.11.
Size: 2 Byte, Default Value: 1

Setting Description
1 Tenth of seconds
2 Seconds

Parameter 20: One Click Scene Activation Set

Defines the Scene Activation Set value sent to the Lifeline group with 1 Click on the external switch.
Size: 2 Byte, Default Value: 0

Setting Description
0 No value is sent
1 - 255 Value sent to the Lifeline group

Parameter 21: Two Clicks Scene Activation Set

Defines the Scene Activation Set value sent to the Lifeline group with 2 Clicks on the external switch.
Size: 2 Byte, Default Value: 0

Setting Description
0 No value is sent
1 - 255 Value sent to the Lifeline group

Parameter 22: Three Clicks Scene Activation Set

Defines the Scene Activation Set value sent to the Lifeline group with 3 Clicks on the external switch.
Size: 2 Byte, Default Value: 0

Setting Description
0 No value is sent
1 - 255 Value sent to the Lifeline group

Parameter 60: Start-up Status

Defines the status of the device following a restart.
Size: 1 Byte, Default Value: 3

Setting Description
1 Relay ON
2 Relay Off
3 Status prior to restart

Parameter 62: Type of external switch

Defines the type of external switch connected to the device.
Size: 1 Byte, Default Value: 1

Setting Description
0 The actions on the external switch are ignored. In this mode, the device can only be controlled through the network.
1 The external switch is a momentary switch type
2 The external switch is a traditional switch (toggle switch)

Technical Data

Dimensions 37 x 37 x 17 mm
Weight 27 gr
Hardware Platform ZM5101
EAN 8059265060061
IP Class IP 20
Voltage 230 V
Load 13 A
Device Type Relais Switch
Generic Device Class Binary Switch
Specific Device Class Binary Power Switch
Firmware Version 01.00
Z-Wave Version 06.04
Z-Wave Product Id 0x0149.0x1214.0x0900
Frequency Europe - 868,4 Mhz
Maximum transmission power 5 mW

Supported Command Classes

  • Basic
  • Switch Binary
  • Association Grp Info
  • Device Reset Locally
  • Zwaveplus Info
  • Supervision
  • Configuration
  • Manufacturer Specific
  • Powerlevel
  • Firmware Update Md
  • Association
  • Version
  • Multi Channel Association
  • Security
  • Transport Service
  • Security 2

Controlled Command Classes

  • Transport Service
  • Security 2

Explanation of Z-Wave specific terms

  • Controller — is a Z-Wave device with capabilities to manage the network. Controllers are typically Gateways,Remote Controls or battery operated wall controllers.
  • Slave — is a Z-Wave device without capabilities to manage the network. Slaves can be sensors, actuators and even remote controls.
  • Primary Controller — is the central organizer of the network. It must be a controller. There can be only one primary controller in a Z-Wave network.
  • Inclusion — is the process of adding new Z-Wave devices into a network.
  • Exclusion — is the process of removing Z-Wave devices from the network.
  • Association — is a control relationship between a controlling device and a controlled device.
  • Wakeup Notification — is a special wireless message issued by a Z-Wave device to announces that is able to communicate.
  • Node Information Frame — is a special wireless message issued by a Z-Wave device to announce its capabilities and functions.