Quickstart

This is a secure On/Off Power Switch for XXXQFrequencyName. To run this device please connect it to your mains power supply. To add this device to your network execute the following action:
Place your Z-Wave controller in "Inclusion" mode. Then tap either the top or bottom paddle once to initiation Inclusion.

Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.
Attention: This manual is automatically generated from Z-Wave Alliance Product data and may be incomplete. Please refer to the Manufacturers Manual for more information.

Product Description

ZLINKs WS-100 is a Z-Wave Plus certified device with S2 security and Smart Start features. You can now add this device securely and with ease using QR code on the product with compatible gateways supporting S2 and Smart Start. Sleek WS-100 communicates with other Z-Wave certified devices and updates your home into a smart home. ZLINK WS-100 replaces a standard in-wall light switch turning it into a Z-Wave controlled network device with manual and remote ON/OFF control. ZLINK WS-100 supports, Instant Feedback of manual status to compatible gateways as well as Central Scene to allow setting multiple scene control throughout the home, with gateways supporting Central Scene. Each Z-Wave device serves as a node to repeat the signal in the network, thus, extending the overall Z-Wave mesh wireless network range.Additional Features: Power 120 VAC, 60Hz, up to 1800 watts Region US: 908.4, 916 MHz Works with incandescent, CFL & LED lights Remotely or manually turns ON or OFF lights Fits standard wall plates (wall plate not included) Works with any certified gateway supporting Z-Wave

Reset to factory default	1. Turn the connected light ON with the rocker2. Quickly tap the topside of the rocker 3 times3. Then quickly tap the bottom side of the rocker 3 timesIf you see the lights turn OFF then ON it means that the module has been reset successfully.Please use this procedure only when the network primary controller is missing or otherwise inoperable.
Inclusion	Place your Z-Wave controller in "Inclusion" mode. Then tap either the top or bottom paddle once to initiation Inclusion.
Exclusion	Place your Z-Wave controller in "Exclusion" mode. Then tap either the top or bottom paddle once to initiation Exclusion.
NIF	XXXNIF
Wakeup	XXXWakeupDescription
Protection	XXXProtection
FirmwareUpdate	XXXFirmwareUpdate
SetAssociation	XXXSetAssociation

Association Groups:

Group Number	Maximum Nodes	Description
1	5	1. Z-Wave Plus Lifeline2. Central Scene Notification3. Switch Binary Report4. Device Reset Locally Notification

Configuration Parameters

Parameter 3: Night Light

The LED indicator will be OFF when the connected light is ON and vice versa.When value =0 the LED indicator will be OFF when the the connected light is ON, and the LED will be ON when the connected light is OFF. If value =1 the LED indicator will be ON when the connected light is ON, and the LED indicator will be OFF when the connected light is OFF. If value =2 the LED indicator will always be OFF regardless of the load status
Size: 1 Byte, Default Value: 0

Setting Description
0 - 2 When value =0 the LED indicator will be OFF when the the connected light is ON, and the LED will be ON when the connected light is OFF. If value =1 the LED indicator will be ON when the connected light is ON, and the LED indicator will be OFF when the connected light is OFF. If value =2 the LED indicator will always be OFF regardless of the load status

Setting	Description
0 - 2	When value =0 the LED indicator will be OFF when the the connected light is ON, and the LED will be ON when the connected light is OFF. If value =1 the LED indicator will be ON when the connected light is ON, and the LED indicator will be OFF when the connected light is OFF. If value =2 the LED indicator will always be OFF regardless of the load status

Parameter 4: Orientation of ON/OFF on rocker switch

The orientation of the ON/OFF on the rocker switch can be inverted using parameter 4. If value =0, the connected light will turn ON by pressing the top side of the rocker switch and turn OFF by pressing the bottom side. If value =1 the connected light will turn OFF by pressing the top side of the rocker switch and turn ON by pressing the bottom side.
Size: 1 Byte, Default Value: 0

Setting Description
0 - 1 If value =0, the connected light will turn ON by pressing the top side of the rocker switch and turn OFF by pressing the bottom side. If value =1 the connected light will turn OFF by pressing the top side of the rocker switch and turn ON by pressing the bottom side.

Setting	Description
0 - 1	If value =0, the connected light will turn ON by pressing the top side of the rocker switch and turn OFF by pressing the bottom side. If value =1 the connected light will turn OFF by pressing the top side of the rocker switch and turn ON by pressing the bottom side.

Technical Data

Hardware Platform	ZM5202
Device Type	On/Off Power Switch
Network Operation	Always On Slave
Firmware Version	HW: 255 FW: 50.03
Z-Wave Version	6.81.00
Certification ID	ZC10-18025995
Z-Wave Product Id	0x0315.0x4447.0x3033
Electric Load Type	FluorescentIncandescentLED
Color	White
Neutral Wire Required	ok
Firmware Updatable	Updatable by Consumer by RF
Switch Type	Decorator Paddle Rocker
Z-Wave Scene Type	Scene & Central Scene
Outdoor Use	ok
Frequency	XXfrequency
Maximum transmission power	XXantenna

ZLINK

Z-Wave In-Wall On/Off Switch

SKU: WS-100