Quickstart
This is a
Notification Sensor for XXXQFrequencyName.
To run this device please connect it to your mains power supply.
To add this device to your network execute the following action:
This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufactures and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.-Open the cover by removing the bottom fixing screw (using a Philips screwdriver) on the Water Sensor.-Insert the battery in the battery compartment-Put the Z-wave gateway or control panel into Inclusion or Learning mode (please refer to the Z-wave gateway or control panel manual).-Within 1.5 seconds, press the Test Button 3 times.-Refer to the operation manual of the Z-wave gateway or control panel to complete the learn-in process.-If the sensor has already been included (learnt) into another Z-wave Gateway/Control Panel, or if the sensor is unable to be learnt into the current Z-wave Gateway/Control Panel, please exclude it first (see Exclusion) before attempting to include it into the current Z-wave Gateway/Control Panel.-Reattach the cover to the base and tighten the bottom-fixing screw.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law.
The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material.
Use this equipment only for its intended purpose. Follow the disposal instructions.
Do not dispose of electronic equipment or batteries in a fire or near open heat sources.
Attention: This manual is automatically generated from
Z-Wave Alliance Product
data and may be incomplete. Please refer to the
Manufacturers Manual for more information.
Product Description
The WS-15ZW is a Z-Wave water sensor designed to detect leaks/floods and to prevent water damage. During a water alarm, the WS-15ZW generates a 95-decibel siren and flashes its red LED, providing audible and visual alerts to prompt a timely response.
| Reset to factory default |
(Only use factory reset when network Control Panel/Gateway is missing or inoperable).-Press and hold the Test Button of the Water sensor for 12 seconds to factory reset. |
| Inclusion |
This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufactures and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.-Open the cover by removing the bottom fixing screw (using a Philips screwdriver) on the Water Sensor.-Insert the battery in the battery compartment-Put the Z-wave gateway or control panel into Inclusion or Learning mode (please refer to the Z-wave gateway or control panel manual).-Within 1.5 seconds, press the Test Button 3 times.-Refer to the operation manual of the Z-wave gateway or control panel to complete the learn-in process.-If the sensor has already been included (learnt) into another Z-wave Gateway/Control Panel, or if the sensor is unable to be learnt into the current Z-wave Gateway/Control Panel, please exclude it first (see Exclusion) before attempting to include it into the current Z-wave Gateway/Control Panel.-Reattach the cover to the base and tighten the bottom-fixing screw. |
| Exclusion |
The Water sensor must be removed from existing Z-wave network before being included into another. There are two methods available to exclude a device:Exclusion Mode-Put the Z-wave gateway or control panel into Exclusion mode (please refer to the Z-wave gateway or control panel manual).-Within 1.5 seconds, press the Test Button 3 times and the Water sensor will be removed from the Z-wave network. |
| NIF |
XXXNIF |
| Wakeup |
This function uses the Z-Wave Wake Up Command Class. The Wake Up Command Class allows the battery-powered Water Sensor to notify the Control Panel/Gateway that it is awake and ready to receive any queued commands. The wake up interval time period is programmed automatically according to Control Panels setting when The Water Sensor is included. The recommended setting of the interval time is between 30 to 60 minutes. |
| Protection |
XXXProtection |
| FirmwareUpdate |
XXXFirmwareUpdate |
| SetAssociation |
XXXSetAssociation |
Association Groups:
| Group Number |
Maximum Nodes |
Description |
| 3 |
5 |
Group 1 for LifeLine:Notification CC,V4 (COMMAND_CLASS_NOTIFICATION)Battery CC (COMMAND_CLASS_BASIC)Device Reset Locally CCGroup 2 for Basic Set:Basic CC, v2 (COMMAND_CLASS_BASIC)Group 3 for Notification Report:Notification CC,V4 (COMMAND_CLASS_NOTIFICATION) |
Technical Data
| Hardware Platform |
ZM5202 |
| Device Type |
Notification Sensor |
| Network Operation |
Reporting Sleeping Slave |
| Firmware Version |
01 |
| Z-Wave Version |
6.51.06 |
| Certification ID |
ZC10-15080008 |
| Z-Wave Product Id |
0x018E.0x0003.0x0003 |
| Frequency |
XXfrequency |
| Maximum transmission power |
XXantenna |
