Quickstart
This is a
Notification Sensor for XXXQFrequencyName.
To run this device please connect it to your mains power supply.
To add this device to your network execute the following action:
4.For Inclusion in (adding to) a network: Put the Z-Wave Interface Controller into inclusion mode, and following its instruction to add the ZD2301 to your controller. To get in the inclusion mode, the distance between sensor and controller is suggested to be in one meter. Press the program switch of ZD2301 for sending the NIF.After sending NIF, Z-Wave will send the auto inclusion; otherwise, ZD2301 will go to sleep after 20 seconds.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law.
The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material.
Use this equipment only for its intended purpose. Follow the disposal instructions.
Do not dispose of electronic equipment or batteries in a fire or near open heat sources.
Attention: This manual is automatically generated from
Z-Wave Alliance Product
data and may be incomplete. Please refer to the
Manufacturers Manual for more information.
Product Description
Visions wireless 4 in 1 Multi-Sensor (door window contact sensor, humidity sensor, temperature sensor, and light sensor) of the home security device. This sensor is a Z-Wave enabled device two-way (interoperable, RF mesh networking technology) and is fully compatible with any Z-Wave enabled network and its security framework. Every main powered Z-Wave enabled device acts as a signal repeater and multiple devices result in more possible transmission routes which helps eliminate RF dead-spotsThis door sensor sends Z-Wave signal when door or window is opened and closed or humidity, temperature, luminous change.When the device is secure included into Z-Wave network, above communication will be encrypted. Security enabled_ Z-Wave controller must be used to fully utilize the product.
| Reset to factory default |
Factory Default Reset: *Open the rear cover to send the Alarm Report and then press the program switch 10 times in 10 seconds, ZD2301 will send the Device Reset Locally command and reset to the factory default. *Please use this procedure only in the event that the network primary controller is missing or otherwise inoperable. |
| Inclusion |
4.For Inclusion in (adding to) a network: Put the Z-Wave Interface Controller into inclusion mode, and following its instruction to add the ZD2301 to your controller. To get in the inclusion mode, the distance between sensor and controller is suggested to be in one meter. Press the program switch of ZD2301 for sending the NIF.After sending NIF, Z-Wave will send the auto inclusion; otherwise, ZD2301 will go to sleep after 20 seconds. |
| Exclusion |
5.For Exclusion from (removing from) a network: Put the Z-Wave Interface Controller into exclusion mode, and following its instruction to delete the ZD2301 from your controller.Press the program switch of ZD2301 for 1 second at least to be excluded.Note: All user and network settings will be cleared and the device reset to factory defaults when the device is excluded. |
| NIF |
XXXNIF |
| Wakeup |
Awake Mode:Press the Program SW, the LED will flash one time and ZD2301 will send Wake Up Notification after 5 seconds. If ZD2301 received Wake Up No More Information command then the ZD2301 will go to sleep or it will wait 10 seconds then go to sleep. It will precede all the commands after sending the Wake Up Notification |
| Protection |
XXXProtection |
| FirmwareUpdate |
XXXFirmwareUpdate |
| SetAssociation |
XXXSetAssociation |
Association Groups:
| Group Number |
Maximum Nodes |
Description |
| 1 |
5 |
Z-Wave Plus LifelineLifeline group used command : Notification Report, Device Reset Locally. |
Technical Data
| Hardware Platform |
ZM5202 |
| Device Type |
Notification Sensor |
| Network Operation |
Reporting Sleeping Slave |
| Firmware Version |
02 |
| Z-Wave Version |
6.51.06 |
| Certification ID |
ZC10-15110007 |
| Z-Wave Product Id |
0x0109.0x201F.0x1F20 |
| Frequency |
XXfrequency |
| Maximum transmission power |
XXantenna |
