Quickstart

This is a Z-Wave Device for Europe. To run this device please connect it to your mains power supply.



Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

What is Z-Wave?

Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.

Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.

This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.

If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.

For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.

Product Description

The Zipatile 2 by Zipato is a very flexible smart home gateway. The Zipatile 2 has an easy to use but powerful web-based user interface which allows to monitor all connected devices and automation rules, created with the ‘Zipato Rule Creator’. The intuitive graphical user interface allows to create own scenes and rules without programming skills. Once configured, the gateway will work independent, but allows cloud support for advanced monitoring, messaging and programming services.

Feutures:

SYSTEM
Quad-Core Cortex ARM CPU
Mali400 MP2 GPU
2GB RAM
8GB FLASH
Android 8.1 Oreo

NETWORK
Z-Wave PLUS
Ethernet (built-in)
Wi-Fi 802.11 b/g/n
Bluetooth 4.x
DECT

SENSORS
Noise
Light
Humidity
Temperature
Motion
Shock

POWER
Power input: 5VDC
Power supply input: 100-240VAC, 50/60Hz
Power usage: <2W (Idle), 7W (Max.)
Backup battery: Li-Ion 3.7V 3500mAh
POE (Power Over Ethernet, optional)
HVAC power (using C wire, optional)

INPUT/OUTPUT
Touch sensitive 8” screen, 800x1280px
3 programmable scene buttons
4 dry outputs 230VAC, 1A (60 W max)
1 dry input 230VAC
HVAC interface (support for 2-5 wire
thermostat installations, HVAC version only)
RS-485 interface
Security camera with privacy switch
Multi-sound alarm siren, 100 dB @ 10cm
Stereo speakers 2x1W
Microphone

Download high resolution images for Zipato products.

Prepare for Installation / Reset

Please read the user manual before installing the product.

In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.

Safety Warning for Mains Powered Devices

ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.

Inclusion/Exclusion

On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.

Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.

Quick trouble shooting

Here are a few hints for network installation if things dont work as expected.

  1. Make sure a device is in factory reset state before including. In doubt exclude before include.
  2. If inclusion still fails, check if both devices use the same frequency.
  3. Remove all dead devices from associations. Otherwise you will see severe delays.
  4. Never use sleeping battery devices without a central controller.
  5. Dont poll FLIRS devices.
  6. Make sure to have enough mains powered device to benefit from the meshing

Technical Data

Dimensions 0.2000000x0.2000000x0.0150000 mm
Weight 796 gr
EAN 3858890734218
Frequency Europe - 868,4 Mhz
Maximum transmission power 5 mW

Explanation of Z-Wave specific terms