Quickstart

This is a On/Off Power Switch for XXXQFrequencyName. To run this device please connect it to your mains power supply. To add this device to your network execute the following action:
For Inclusion in (adding to) a network: Put the Z-Wave Interface Controller into inclusion mode, and following its instruction to add the ZL7261 into your controller.To get in the Inclusion mode, the distance between ZL7261 and controller is suggested to be in one meter. By power up to get included for first time, or press the Program switch (The LED at the top of plug-in) 3 times within 2 seconds to be included.



Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.
Attention: This manual is automatically generated from Z-Wave Alliance Product data and may be incomplete. Please refer to the Manufacturers Manual for more information.

Product Description

This Power Monitoring On/Off Module is a Z-Wave enabled device (interoperable, two-way RF mesh networking technology) and is fully compatible with any Z-Wave enabled network. Every main powered Z-Wave enabled device acts as a signal repeater and multiple devices result in more possible transmission routes, which helps eliminate RF dead-spot.Z-Wave enabled devices displaying the Z-Wave logo can also be used with it regardless of the manufacturer, and ours can also be used in other manufacturers Z-Wave enabled networks.This module will send On/Off signal to the appliance that attached to this module by receiving Z-Wave signal from controller or manually switch.It also sends the energy consumption to the controller when it requests.With special design, this module wont interfere the other power outlet when plug into the AC outlet.This module also acts as repeater (supporting FLiRS).

Reset to factory default Reset: Press the Program Switch (The LED at the top of plug-in) then power on (plug-in) and hold for 5 seconds before release the switch.Noticed:only use Reset for the situation where the primary controller is inoperable or lost.
Inclusion For Inclusion in (adding to) a network: Put the Z-Wave Interface Controller into inclusion mode, and following its instruction to add the ZL7261 into your controller.To get in the Inclusion mode, the distance between ZL7261 and controller is suggested to be in one meter. By power up to get included for first time, or press the Program switch (The LED at the top of plug-in) 3 times within 2 seconds to be included.
Exclusion For Exclusion from (removing from) a network: Set up the Z-Wave Interface Controller into exclusion mode, and following its instruction to delete the ZL7261 from your controller.Press the Program Switch (The LED at the top of plug-in) 3 times within 2 seconds to be excluded.
NIF XXXNIF
Wakeup XXXWakeupDescription
Protection XXXProtection
FirmwareUpdate XXXFirmwareUpdate
SetAssociation XXXSetAssociation

Association Groups:

Group Number Maximum Nodes Description
1 5 Central Static Controller Lifeline Signals

Configuration Parameters

Parameter 1: Auto report timing

Automatic Meter Report interval for kWh/kVAh
Size: 1 Byte, Default Value: 60

Setting Description
60 - 255 The number of seconds desired between automatic meter reports.

Parameter 2: Report when Watt change

The change in watt consumption that will cause the transmission of voltage, current, and wattage to be sent.
Size: 2 Byte, Default Value: 50

Setting Description
5 - 3600 The number of watts change to cause reports to be sent.

Technical Data

Hardware Platform ZM5202
Device Type On/Off Power Switch
Network Operation Always On Slave
Firmware Version 02
Z-Wave Version 6.51.02
Certification ID ZC10-14080003
Z-Wave Product Id 0x0109.0x201A.0x1A02
Frequency XXfrequency
Maximum transmission power XXantenna
CEPT (Europe)On/Off Power Switch