Vision
Power Switch
SKU: ZL7434EU-5
Quickstart
This is a
Put the Z-Wave Interface Controller into inclusion mode, and following its instruction to add the ZL 7434-5 to your controller.To get in the inclusion mode, the distance between module and controller is suggested to be in one meter. Press 3 times program switch within 2 seconds or turn on the wall switch 3 times within 2 seconds (or press toggle switch 3 times) to be included.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
This module provides On/Off control for the appliance that is attached to this module by Z-Wave.It also can control two appliances independently.When the device is secure included into Z-Wave network, Z-Wave communication will be encrypted.* Size: 3.95 x 5.0 x 1.9 cm* Operating Range: Up to 100 feet line of sight* Operating Temp.: -10C~ 60C (14F~140F)* Operating Voltage: 90 VAC~240 VAC, 50/60 Hz* Max. Loading: 15A
| Reset to factory default | Power off first, press Program Switch and power on, ZL7434-5 will send the Device Reset Locally Notification command and reset to the factory default. (Remark: This is to be used only in the case of primary controller being inoperable or otherwise unavailable.) |
| Inclusion | Put the Z-Wave Interface Controller into inclusion mode, and following its instruction to add the ZL 7434-5 to your controller.To get in the inclusion mode, the distance between module and controller is suggested to be in one meter. Press 3 times program switch within 2 seconds or turn on the wall switch 3 times within 2 seconds (or press toggle switch 3 times) to be included. |
| Exclusion | Put the Z-Wave Interface Controller into exclusion mode, and following its instruction to delete the ZL 7434-5 from your controller. Press 3 times program switch within 2 seconds or turn on the wall switch 3 times within 2 seconds (or press toggle switch 3 times) to be excluded. |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | Z-Wave Plus Lifeline |
Configuration Parameters
Parameter 1: Light type
To select the light type, 1 Wall Switch, 2 Wall Switches or wall switch with Light Indicator. Size: 1 Byte, Default Value: 2
| Setting | Description |
|---|---|
| 1 | 1 or 2 Wall Switches |
| 2 | 1 Wall Switch with Light Indicator(factory default). |
Parameter 2: Switch button type
If customer chose 1 or 2 wall switches, then they have also select switch button type. Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 1 | With common on/off type switch button used(factory default). |
| 2 | With momentary type switch button used. |
Technical Data
| Hardware Platform | ZM5202 |
| Device Type | On/Off Power Switch |
| Network Operation | Always On Slave |
| Firmware Version | 02 |
| Z-Wave Version | 6.51.06 |
| Certification ID | ZC10-15120003 |
| Z-Wave Product Id | 0x0109.0x200C.0x0C06 |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |