Quickstart

This is a Binary Power Switch for XXXQFrequencyName. To run this device please connect it to your mains power supply.

Triple click one of the buttons on the device will include the device. A green blinking of LED will indicate successful inclusion. The device is excluded by triple click to one of the buttons.



Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

Product Description

The Z-Wave.Me Switch Flush Mountable is a wireless actuator able to switch loads up to 2300 W. The device is delivered as complete set with flush mountable insert, paddle and mounting frame compatible to the design of the switching series DURO 2000 SI in color pearl white from Busch Jaeger. The paddle of the device is used to control the device itself but can also be configured to activate scenes in a central IP gateway or controller. The status of the switch is indicated on a dual color LED for test purposes and every status change is - if configured - reported to a central IP gateway or controller. The function of the local paddle can be configured as detached from the local operation. In this local control, different devices are controlled by Z-Wave while the local actuator is controlled by other devices using Z-Wave. This device is designed for a 3 wire system and needs a neutral wire in the wall box.

Installation

The insert is designed to fit into standard circular European wall boxes with 60 mm diameter. The insert combined with the mounting plate can be screwed in top of the wall box using the two screws delivered with the device. The mounting frame is then attached to the mounting plate and the switch is completed by pushing the switching paddle into the mounting frame. Mind the arrow on the inserts top side showing the mounting direction of the insert. It is also possible to mount the insert without any local operation behind a cover or inside a lamp. The mounting plate, frame and the switching paddle become useless in such a scenario.

The schematics below shows how to wire the actuator. The two wired from the mains distribution panel are connected to the inserts contacts N and L. The contact S is the switched contact and need to be connected to the cable to the load. The second wire to the load is connected to N as well. Both contacts marked as N are connected with each other.

A fuse protects the electronics of the actuator. The fuse is accessible on the top side of the device. Inside the plug there is the working fuse plus a spare fuse.

Product Usage

The actuator is operated by the local switching paddles or wirelessly using Z-Wave commands (communication patterns 1, 4, 5 and 7). If the insert is mounted correctly pushing the upper part of the paddle will turn on the load; pushing the lower part of the paddle will turn off the electric load.

The device is also able to report status changes to a controller (communication pattern 2) and to remotely operate other devices (communication pattern 5) by sending wireless Z-Wave commands. In case the remote device is a switch as well the remote operation is similar to the local operation by pushing upper to lower part of the switching paddle. However the device can also be configured with configuration parameter 13 and 14 to operate remote dimmers. To dim a remote device the paddle needs to be pushed and hold (upper part to dim up, lower part to dim down). Its furthermore possible to assign remote operation functions to the double click of the paddles.

Configuration parameter 2 enables a special function of the device. Its possible to define a timeout to automatically turn off the device after it was turned on manually.

Reset to factory default XXXResetDescription
Inclusion

Blinking red/green LED indicates that the device is in factory reset state. Once the controller is turned into inclusion mode triple click of the buttons on the device will include the device. A green blinking of the LED will indicate successful inclusion that will be turned off shortly afterwards. The device is excluded by triple click to one of the buttons when the controller is in exclusion mode.

Exclusion

Blinking red/green LED indicates that the device is in factory reset state. Once the controller is turned into inclusion mode triple click of the buttons on the device will include the device. A green blinking of the LED will indicate successful inclusion that will be turned off shortly afterwards. The device is excluded by triple click to one of the buttons when the controller is in exclusion mode.

NIF XXXNIF
Wakeup XXXWakeupDescription
Protection XXXProtection
FirmwareUpdate XXXFirmwareUpdate
SetAssociation XXXSetAssociation

Configuration Parameters

Technical Data

Dimensions 0.0520000x0.0520000x0.0300000 mm
Weight 55 gr
EAN 0019962003400
Device Type On/Off Power Switch
Generic Device Class Binary Switch
Specific Device Class Binary Power Switch
Certification ID ZC08-11090001
Frequency Europe - 868,4 Mhz
Maximum transmission power 5 mW
EuropeOn/Off Power Switch