Aeotec
MultiSensor Gen5
SKU: ZW074-B
Quickstart
This is a
N/A
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
TheAeotecbyAeonLabsMultiSensorGen5lookslike a motion sensor and itacts like one too.But its also so much more. Installing this 1 piece of Z-Wave technology isthe same as installing 4pieces ofZ-Wavetechnology.Your home control network will immediately understand motion, temperature, humidity and light readings wherever Multisensor installed. Those intelligent readings will equate to intelligenceautomation. And intelligent automation will give you the perfect, smart home.
| Reset to factory default | Press and hold the Z-Wave button that you can find in back of the product for 20 seconds and then release. This procedure should only be used when the primary controller is inoperable. |
| Inclusion | N/A |
| Exclusion | N/A |
| NIF | XXXNIF |
| Wakeup | Press and hold the Z-Wave button for 3 seconds will trigger sending the Wake up notification command. If press the Z-Wave button 3 times, the MultiSensor will wake up for 10 minutes. |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | Group 1 is assigned to the Lifeline association group and every device has 5 nodes to associate.The Motion sensor, Humidity sensor, thermometer and light sensor reports will be sent to the associated nodes in Group 1. |
Special Operations as Z-Wave Controller
As long as this device is not included into a Z-Wave network of a different controller it is able to manage its own Z-Wave network as primary controller. As a primary controller the device can include and exclude other devices in its own network, manage associations, and reorganize the network in case of problems. The following controller functions are supported:
Inclusion of other devices
Communication between two Z-Wave devices only works if both belong to the same wireless network. Joining a network is called inclusion and is initiated by a controller. The controller needs to be turned into the inclusion mode. Once in this inclusion mode the other device needs to confirm the inclusion - typically by pressing a button.
If current primary controller in your network is in special SIS mode this and any other secondary controller can also include and exclude devices.
To become primary a contoller have to be resetted and then include a device.
Turn the primary controller of Z-Wave network into inclusion mode, short press the products Z-Wave button that you can find in the back of the product.
Exclusion of other devices
The primary controller can exclude devices from the Z-Wave network. During exclusion the relationship between the device and the network of this controller is terminated. No communication between the device and other devices still in the network can happen after a successful exclusion. The controller needs to be turned into the exclusion mode. Once in this exclusion mode the other device needs to confirm the exclusion - typically by pressing a button.
Attention: Removing a device from the network means that it is turned back into factory default status. This process can also exclude devices from it's previous network.
Turn the primary controller of Z-Wave network into exclusion mode, short press the products Z-Wave button that you can find in back of the product.
Configuration Parameters
Parameter 101: Which report needs to be sent in Report group 1
This parameter is used to configure to send the Humidity sensor, thermometer, light sensor and battery reports automatically in Report group 1.Note: The values corresponding to the first four bits of the parameter value may be combined to create different combinations of reports that you wish to have sent.For example, the temperature sensor report is the value 32 and the battery report is the value 1, so setting parameter 101 to a value of 33 will result in both temperature sensor report and battery report to be reported.See the full description of the parameter values for other possible settings. Size: 4 Byte, Default Value: 255
| Setting | Description |
|---|---|
| 64 | The humidity sensor report is selected. |
| 128 | The light sensor report is selected. |
| 1 | The battery report is selected. |
| 32 | The temperature sensor report is selected. |
Parameter 102: Which report needs to be sent in Report group 2.
This parameter is used to configure to send the Humidity sensor, thermometer, light sensor and battery reports automatically in Report group 2.Note: The values corresponding to the first four bits of the parameter value may be combined to create different combinations of reports that you wish to have sent.For example, the temperature sensor report is the value 32 and the battery report is the value 1, so setting parameter 102 to a value of 33 will result in both temperature sensor report and battery report to be reported.See the full description of the parameter values for other possible settings. Size: 4 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 128 | The light sensor report is selected. |
| 1 | The battery report is selected. |
| 32 | The temperature sensor report is selected. |
| 64 | The humidity sensor report is selected. |
Parameter 103: Which report needs to be sent in Report group 3.
This parameter is used to configure to send the Humidity sensor, thermometer, light sensor and battery reports automatically in Report group 3.Note: The values corresponding to the first four bits of the parameter value may be combined to create different combinations of reports that you wish to have sent.For example, the temperature sensor report is the value 32 and the battery report is the value 1, so setting parameter 103 to a value of 33 will result in both temperature sensor report and battery report to be reported.See the full description of the parameter values for other possible settings. Size: 4 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 32 | The temperature sensor report is selected. |
| 64 | The humidity sensor report is selected. |
| 128 | The light sensor report is selected. |
| 1 | The battery report is selected. |
Parameter 111: The interval time of sending reports in Report group 1
This parameter is used to configure the interval time of the sensor report in Report group 1.The time unit is second. Size: 4 Byte, Default Value: 1800
| Setting | Description |
|---|---|
| 5 - 2678400 | The range of interval time is 5 to 2678400. |
Parameter 112: The interval time of sending reports in Report group 2.
This parameter is used to configure the interval time of the sensor report in Report group 2.The time unit is second. Size: 4 Byte, Default Value: 1800
| Setting | Description |
|---|---|
| 5 - 2678400 | The range of interval time is 5 to 2678400. |
Parameter 113: The interval time of sending reports in Report group 3
This parameter is used to configure the interval time of the sensor report in Report group 3.The time unit is second. Size: 4 Byte, Default Value: 1800
| Setting | Description |
|---|---|
| 5 - 2678400 | The range of interval time is 5 to 2678400. |
Parameter 2: Enable/Disable waking up for 10 minutes when re-power on (battery mode) the MultiSensor.
This parameter is used to enable/disable waking up for 10 minutes when re-power on (battery mode) the MultiSensor.1. Value = 0, disable.2. Value =others, enable. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Disable waking up for 10 minutes when re-power on (battery mode) the MultiSensor. |
| 1 | Enable waking up for 10 minutes when re-power on (battery mode) the MultiSensor. |
Parameter 252: Enable/disable all configuration parameters to be locked
This parameter is used to enable/disable all configuration parameters to be locked.(0 =disable, 1 = enable) Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Disable all configuration parameters to be locked. |
| 1 | Enable all configuration parameters to be locked. |
Parameter 255: Reset to default factory setting
This parameter is used to reset product to default factory setting. (There are just 2 values can be used). Size: 4 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 1 | Resets all configuration parameters to default setting. |
| 1431655765 | Reset the product to default factory setting and be excluded from the Z-wave network. |
Parameter 3: Timeout of the motion sensor
This parameter is used to set the timeout for the motion sensor.Note:(1), The time unit is second if the value range is in 1 to 255. (2), If the value range is in 256 to 15300, the time unit will be minute and its value should follow the below rules:a),Interval time =Value/60, if the interval time can be divided by 60 and without remainder.b), Interval time= (Value/60) +1, if the interval time can be divided by 60 and has remainder.(3), Other values will be ignored. Size: 2 Byte, Default Value: 240
| Setting | Description |
|---|---|
| 1 - 255 | The unit of timeout is second. |
| 256 - 15300 | The unit of timeout is minute. |
Parameter 4: Enable/disable the function of motion sensor.
This parameter is used to enable/disable the function of motion sensor.1. Value=0, disable.2. Value=1, enable. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Disable the function of motion sensor. |
| 1 | Enable the function of motion sensor. |
Parameter 40: Enable/disable the selective reporting only when measurements reach a certain threshold or percentage set in 41-44 below.
This parameter is used to enable/disable the selective reporting only when measurements reach a certain threshold or percentage set in the parameter 41 to 44.This is used to reduce network traffic.(0 == disable, 1 == enable) Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 1 | Enable the selective reporting. |
| 0 | Disable the selective reporting. |
Parameter 41: Threshold change in temperature to induce an automatic report.
Threshold change in temperature to induce an automatic report. Note:1. When the unit is Celsius, threshold=Value.2. When the unit is Fahrenheit, threshold=Value*1.8The accuracy is 0.1. Size: 2 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 - 65535 | Threshold of temperature. |
Parameter 42: Threshold change in humidity to induce an automatic report.
Threshold change in humidity to induce an automatic report. Size: 2 Byte, Default Value: 5
| Setting | Description |
|---|---|
| 0 - 100 | Threshold of humidity |
Parameter 43: Threshold change in luminance to induce an automatic report.
Threshold change in luminance to induce an automatic report. Size: 2 Byte, Default Value: 100
| Setting | Description |
|---|---|
| 0 - 1000 | Threshold of luminance |
Parameter 44: Threshold change in battery level to induce an automatic report.
Threshold change in battery level to induce an automatic report. Size: 2 Byte, Default Value: 5
| Setting | Description |
|---|---|
| 0 - 100 | Threshold of battery level. |
Parameter 46: Enable/disable to send the alarm report of low temperature
This parameter is used to enable/disable to send the alarm report of low temperature(<-15)1, Value=0, disable.2, Value=1, enable(Note:The MultiSensor will report the Multi Level Temperature CC with the value=0xFFFF to controller if the current temperature is less than -15). Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Disable to send the alarm report of low temperature(&amp;amp;amp;amp;amp;amp;amp;amp;lt;-15) |
| 1 | Enable to send the alarm report of low temperature(&amp;amp;amp;amp;amp;amp;amp;amp;lt;-15) |
Parameter 5: Which command would be sent when the motion sensor triggered.
This parameter is used to configure that which command would be sent when the motion sensor triggered.1. Value=1, send Basic Set CC.2. Value=2, send Sensor Binary Report CC. Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 2 | Send Sensor Binary Report CC. |
| 1 | Send Basic Set CC. |
Technical Data
| Hardware Platform | ZM5101 |
| Device Type | Notification Sensor |
| Network Operation | Reporting Sleeping Slave |
| Firmware Version | HW: 4A FW: 1.02 |
| Z-Wave Version | 6.51.01 |
| Certification ID | ZC10-14120005 |
| Z-Wave Product Id | 0x0086.0x0202.0x004A |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |