This is a
N/A
Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.
This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.
If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.
For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.
Aeon Labs Heavy Duty Smart Switch is a Z-Wave device that can report the wattage energy usage and KWH usage to a Z-Wave Controller (especially a gateway), it can be controlled by other Z-Wave devices to turn on/off loads, it can bear up to 40A current of resister loads. It also acts as a repeater that forward Z-Wave command messages to destination nodes if the originating controller is out of range from the destination node.By taking advantage of the Z-Wave mesh network, commands can be routed to their destination via intermediary listening Z-Wave products. Products that are Z-Wave certified can be used and communicate with other Z-Wave certified devices.
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.
This device also allows to be reset without any involvement of a Z-Wave controller. This procedure should only be used when the primary controller is inoperable.
Press and hold the Z-Wave button for 20 seconds and then release.
ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.
On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.
Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.
This device is battery operated and turned into deep sleep state most of the time to save battery life time. Communication with the device is limited. In order to communicate with the device, a static controller C is needed in the network. This controller will maintain a mailbox for the battery operated devices and store commands that can not be received during deep sleep state. Without such a controller, communication may become impossible and/or the battery life time is significantly decreased.
This device will wakeup regularly and announce the wakeup state by sending out a so called Wakeup Notification. The controller can then empty the mailbox. Therefore, the device needs to be configured with the desired wakeup interval and the node ID of the controller. If the device was included by a static controller this controller will usually perform all necessary configurations. The wakeup interval is a tradeoff between maximal battery life time and the desired responses of the device. To wakeup the device please perform the following action: N/A
Here are a few hints for network installation if things dont work as expected.
Z-Wave devices control other Z-Wave devices. The relationship between one device controlling another device is called association. In order to control a different device, the controlling device needs to maintain a list of devices that will receive controlling commands. These lists are called association groups and they are always related to certain events (e.g. button pressed, sensor triggers, ...). In case the event happens all devices stored in the respective association group will receive the same wireless command wireless command, typically a 'Basic Set' Command.
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 5 | Group 1 is assigned to the Lifeline association group and every device has 5 nodes to associate. |
2 | 5 | When the Heavy Duty Smart Switch Gen5 receives the following commands, it will forward the commands to all node IDs (in Group 2).The command will be sent via multicast (if there are more than 2 Node IDs) or single-cast (if there is only one Node ID). Commands: Basic Set, Switch Binary Set, Scene Activation Set. |
As long as this device is not included into a Z-Wave network of a different controller it is able to manage its own Z-Wave network as primary controller. As a primary controller the device can include and exclude other devices in its own network, manage associations, and reorganize the network in case of problems. The following controller functions are supported:
Communication between two Z-Wave devices only works if both belong to the same wireless network. Joining a network is called inclusion and is initiated by a controller. The controller needs to be turned into the inclusion mode. Once in this inclusion mode the other device needs to confirm the inclusion - typically by pressing a button.
If current primary controller in your network is in special SIS mode this and any other secondary controller can also include and exclude devices.
To become primary a contoller have to be resetted and then include a device.
Turn the primary controller of Z-Wave network into inclusion mode, short press the products Z-Wave button.
The primary controller can exclude devices from the Z-Wave network. During exclusion the relationship between the device and the network of this controller is terminated. No communication between the device and other devices still in the network can happen after a successful exclusion. The controller needs to be turned into the exclusion mode. Once in this exclusion mode the other device needs to confirm the exclusion - typically by pressing a button.
Attention: Removing a device from the network means that it is turned back into factory default status. This process can also exclude devices from it's previous network.
Turn the primary controller of Z-Wave network into exclusion mode, short press the products Z-Wave button.
Z-Wave products are supposed to work out of the box after inclusion, however certain configuration can adapt the function better to user needs or unlock further enhanced features.
IMPORTANT: Controllers may only allow configuring signed values. In order to set values in the range 128 ... 255 the value sent in the application shall be the desired value minus 256. For example: To set a parameter to 200 it may be needed to set a value of 200 minus 256 = minus 56. In case of a two byte value the same logic applies: Values greater than 32768 may needed to be given as negative values too.
This parameter is used to restore the parameter 101, 102 and 103 to default setting. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 - 1 | When value==1, parameters 101 ~103 will be restored to default setting.When value==0, it will not restore any parameter. |
This parameter is used to configure which reports need to be sent in Report Group 1 (The possible values as below). Size: 4 Byte, Default Value: 4
Setting | Description |
---|---|
0 - 15 | When value==1, which means the Voltage report is configured to be sent in Report Group 1. When value==2, which means the Current report is configured to be sent in Report Group 1. When value==4, which means the Wattage report is configured to be sent in Report Group 1. When value==8, which means the KWH report is configured to be sent in Report Group 1. When value==15, which means the Voltage , Current , Wattageand KWH report are all configured to be sent in Report Group 1. The other values will be reserved. |
This parameter is used to configure which reports need to be sent in Report Group 2 (The possible values as below). Size: 4 Byte, Default Value: 8
Setting | Description |
---|---|
0 - 15 | When value==1, which means the Voltage report is configured to be sent in Report Group 2. When value==2, which means the Current report is configured to be sent in Report Group 2. When value==4, which means the Wattage report is configured to be sent in Report Group 2. When value==8, which means the KWH report is configured to be sent in Report Group 2. When value==15, which means the Voltage , Current , Wattageand KWH report are all configured to be sent in Report Group 2. The other values will be reserved. |
This parameter is used to configure which reports need to be sent in Report Group 3 (The possible values as below). Size: 4 Byte, Default Value: 0
Setting | Description |
---|---|
0 - 15 | When value==1, which means the Voltage report is configured to be sent in Report Group 3. When value==2, which means the Current report is configured to be sent in Report Group 3. When value==4, which means the Wattage report is configured to be sent in Report Group 3. When value==8, which means the KWH report is configured to be sent in Report Group 2. When value==15, which means the Voltage , Current , Wattageand KWH report are all configured to be sent in Report Group 3. The other values will be reserved. |
This parameter is used to restore the parameter 111, 112 and 113 to default setting. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 - 1 | When value==1, parameters 111 ~113 will be restored to default setting. |
This parameter is used to set the interval time of sending report in Report Group 1.(The unit of time is second). Size: 4 Byte, Default Value: 5
Setting | Description |
---|---|
0 - 268435456 | You have a wide range to set the interval time that can be set from 0 to 268435456 seconds. |
This parameter is used to set the interval time of sending report in Report Group 2.(The unit of time is second). Size: 4 Byte, Default Value: 120
Setting | Description |
---|---|
0 - 268435456 | You have a wide range to set the interval time that can be set from 0 to 268435456 seconds. |
This parameter is used to set the interval time of sending report in Report Group 3.(The unit of time is second). Size: 4 Byte, Default Value: 120
Setting | Description |
---|---|
0 - 268435456 | You have a wide range to set the interval time that can be set from 0 to 268435456 seconds. |
This parameter is used to configure the partner ID.0== Aeon Labs Standard Product,1~255== others. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 - 255 | There are 255 different partners can be configured. |
This parameter is used to Enable/Disable Lock all configuration parameters.(0 =disable, 1 = enable) Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 - 1 | When value==0, all configuration parameters are configurable. When value==1, all configuration parameters are not configurable.(Locked). |
This parameter is used to reset product to default factory setting.(There are just 2 values can be used) Size: 4 Byte, Default Value: 0
Setting | Description |
---|---|
0 - 1431655765 | When value==1431655765, it will reset the product to default factory setting and be excluded from Z-wave network. When value==1, it only will reset the all configuration parameters to default setting. The other values will be reserved. |
This parameter is used for the overload protection, which means the load will be disconnected after 5 seconds when the current more than 39.5A. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 - 1 | 0=disabled, 1=enabled |
This parameter is used to Enable/Disable to send notifications to associated devices (in Group 1) when the state of Heavy Duty Smart Switch Gen5s load is changed. (0=send nothing, 1=send hail CC, 2=send basic CC report). Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 - 2 | (0=nothing, 1=hail CC, 2=basic CC report |
This parameter is used to Enable/Disable the function of parameter 91 and 92 below (1=Enabled, 0=Disabled). Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
0 - 1 | 0=disabled, 1=enabled |
This parameter is used to induce an automatic report when the change of the current power is more/less than the threshold in wattage. Size: 2 Byte, Default Value: 50
Setting | Description |
---|---|
0 - 60000 | The threshold can be set from 0 to 60000 watt. |
This parameter is used to induce an automatic report when the change of the current power is more/less than the threshold in percentage. Size: 1 Byte, Default Value: 10
Setting | Description |
---|---|
0 - 100 | The threshold can be set from 0 to 100 percent. |
Hardware Platform | ZM5202 |
Device Type | On/Off Power Switch |
Network Operation | Always On Slave |
Firmware Version | HW: 78 FW: 3.26 |
Z-Wave Version | 6.51.00 |
Certification ID | ZC10-14060004 |
Z-Wave Product Id | 0x0086.0x0103.0x004E |
Frequency | XXfrequency |
Maximum transmission power | XXantenna |