This is a
Turn the primary controller of Z-Wave network into inclusion mode, press the external switch of LED Bulb to turn it off and then press the external switch again to turn it on.
Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.
This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.
If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.
For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.
Aeotec LED Bulb is a low-cost Z-Wave LED module which allows control (on/off/dim) with the use of Z-Wave. Its a bulb has a Smart RGB LED, which can be used to add colour to your home. The bulb has 5 main colour channels available for you to adjust: Red, Green, Blue, Warm White and Cold White. You can configure its colour according to your favour.The LED Bulb is also a security Z-Wave device and supports the Over The Air (OTA) feature for the products firmware upgrade.
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.
This device also allows to be reset without any involvement of a Z-Wave controller. This procedure should only be used when the primary controller is inoperable.
Turn the controller of Z-Wave network into exclusion mode, press the external switch of LED Bulb to turn off and then press the external switch again to turn on it, repeat the operation 3 times.After the LED Bulb is excluded from network, it will be reset to factory default state.Use this procedure only in the event that your primary network controller is missing or inoperable.
ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.
On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.
Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.
Here are a few hints for network installation if things dont work as expected.
Z-Wave devices control other Z-Wave devices. The relationship between one device controlling another device is called association. In order to control a different device, the controlling device needs to maintain a list of devices that will receive controlling commands. These lists are called association groups and they are always related to certain events (e.g. button pressed, sensor triggers, ...). In case the event happens all devices stored in the respective association group will receive the same wireless command wireless command, typically a 'Basic Set' Command.
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 5 | The association group 1 is the Z-Wave Lifeline group. The Hail CC and Basic Report CC (configurable) can be sent to the associated nodes in association group 1. |
2 | 5 | In this group, the Basic Set, Switch Binary Set, Switch Multilevel Start Level Change, Switch Multilevel Stop Level Change, Switch Multilevel Set, Scene Activation Set commands would be sent to the associated nodes in association group 2 when the Bulb receives the Basic Set, Switch Binary Set, Switch Multilevel Start Level Change, Switch Multilevel Stop Level Change, Switch Multilevel Set, Scene Activation Set commands from the main controller. |
Z-Wave products are supposed to work out of the box after inclusion, however certain configuration can adapt the function better to user needs or unlock further enhanced features.
IMPORTANT: Controllers may only allow configuring signed values. In order to set values in the range 128 ... 255 the value sent in the application shall be the desired value minus 256. For example: To set a parameter to 200 it may be needed to set a value of 200 minus 256 = minus 56. In case of a two byte value the same logic applies: Values greater than 32768 may needed to be given as negative values too.
Set the Dimmer mode. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Parabolic curve mode |
1 | Index curve mode |
2 | (Parabolic + Index)/2 mode |
3 | Linear mode |
Set the bulbs state after it is re-powered on. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
0 | The last state before re-power on. |
1 | Always On. |
2 | Always Off. |
Enable/disable to lock Configuration parameters. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Disable |
1 | Enable |
Reset the Bulb to factory default. Size: 4 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Reset all configuration parameters to factory default settings |
1431655765 | Reset the bulb to factory default. |
Enable/disable to send out a report when the color is changed. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Disable |
1 | Hail CC |
Get the Bulbs color value.Note: This parameter is a get-only parameter. Size: 4 Byte, Default Value: 0
Setting | Description |
---|---|
1 - 255 | Bule color value |
256 - 65535 | Green color value |
65536 - 16777215 | Red color value |
Enable/disable the function of using External Switch to turn on/off the bulb. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Disable |
1 | Enable |
Enable/disable the function of using External Switch to changes the bulbs color. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
0 | Disable |
1 | Enable |
Reboot/save/exit Colorful mode.Note: This parameter is a set-only parameter. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Un-reboot Colorful mode. |
1 | Reboot Colorful mode. |
2 | Exit Colorful mode. |
3 | Save the current Colorful mode value and then to be exited. |
Configure the Colorful mode. Size: 4 Byte, Default Value: 157483008
Setting | Description |
---|---|
0 - 31 | Colour Change Speed Level |
32 - 255 | Time Base of Color Change Speed |
256 - 65535 | Cycle Count |
65536 - 16777215 | Brightness |
16777215 - 134217727 | Color Display Cycle |
134217728 - 1073741823 | Color Change Speed Option |
1073741824 - 2147483647 | Color Transition Style |
Set the Change speed. Size: 4 Byte, Default Value: 50332416
Setting | Description |
---|---|
1 - 255 | Set the pause time of OFF. |
256 - 65535 | Set the pause time of ON. |
65536 - 16777215 | Set the speed from ON to OFF. |
16777216 - 2147483647 | Set the speed from OFF to ON. |
Color index configuration when the bulb is in Multi color mode. Size: 4 Byte, Default Value: 2003125025
Setting | Description |
---|---|
1 - 15 | Index 8 |
16 - 255 | Index 7 |
256 - 4095 | Index 6 |
4096 - 65535 | Index 5 |
65536 - 1048575 | Index 4 |
1048576 - 16777215 | Index 3 |
16777216 - 268435455 | Index 2 |
268435456 - 2147483647 | Index 1 |
To set whcih notification can be sent to the associated devices (Group 1) when the state of LED Bulb is changed. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
0 | Nothing |
1 | Hail CC |
2 | Basic CC report. |
Hardware Platform | ZM5101 |
Device Type | Light Dimmer Switch |
Network Operation | Always On Slave |
Firmware Version | HW: 98 FW: 1.05 |
Z-Wave Version | 6.51.06 |
Certification ID | ZC10-16065119 |
Z-Wave Product Id | 0x0086.0x0103.0x0062 |
Firmware Updatable | Updatable by Consumer by RF |
Z-Wave Scene Type | Scene |
Switch Type | Toggle |
Frequency | XXfrequency |
Maximum transmission power | XXantenna |