This is a
Turn the primary controller of Z-Wave network into inclusion mode, press the external switch of LED Bulb to turn it off and then press the external switch again to turn it on.
Aeotec LED Bulb is a low-cost Z-Wave LED module which allows control (on/off/dim) with the use of Z-Wave. Its a bulb has a Smart RGB LED, which can be used to add colour to your home. The bulb has 5 main colour channels available for you to adjust: Red, Green, Blue, Warm White and Cold White. You can configure its colour according to your favour.The LED Bulb is also a security Z-Wave device and supports the Over The Air (OTA) feature for the products firmware upgrade.
Reset to factory default | Turn the controller of Z-Wave network into exclusion mode, press the external switch of LED Bulb to turn off and then press the external switch again to turn on it, repeat the operation 3 times.After the LED Bulb is excluded from network, it will be reset to factory default state.Use this procedure only in the event that your primary network controller is missing or inoperable. |
Inclusion | Turn the primary controller of Z-Wave network into inclusion mode, press the external switch of LED Bulb to turn it off and then press the external switch again to turn it on. |
Exclusion | Turn the primary controller of Z-Wave network into exclusion mode, press the external switch of LED Bulb to turn off and then press the external switch again to turn on it, repeat the operation 3 times. |
NIF | XXXNIF |
Wakeup | XXXWakeupDescription |
Protection | XXXProtection |
FirmwareUpdate | XXXFirmwareUpdate |
SetAssociation | XXXSetAssociation |
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 5 | The association group 1 is the Z-Wave Lifeline group. The Hail CC and Basic Report CC (configurable) can be sent to the associated nodes in association group 1. |
2 | 5 | In this group, the Basic Set, Switch Binary Set, Switch Multilevel Start Level Change, Switch Multilevel Stop Level Change, Switch Multilevel Set, Scene Activation Set commands would be sent to the associated nodes in association group 2 when the Bulb receives the Basic Set, Switch Binary Set, Switch Multilevel Start Level Change, Switch Multilevel Stop Level Change, Switch Multilevel Set, Scene Activation Set commands from the main controller. |
Set the Dimmer mode. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Parabolic curve mode |
1 | Index curve mode |
2 | (Parabolic + Index)/2 mode |
3 | Linear mode |
Set the bulbs state after it is re-powered on. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 | Always On. |
2 | Always Off. |
0 | The last state before re-power on. |
Enable/disable to lock Configuration parameters. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Disable |
1 | Enable |
Reset the Bulb to factory default. Size: 4 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Reset all configuration parameters to factory default settings |
1431655765 | Reset the bulb to factory default. |
Enable/disable to send out a report when the color is changed. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Disable |
1 | Hail CC |
Get the Bulbs color value.Note: This parameter is a get-only parameter. Size: 4 Byte, Default Value: 0
Setting | Description |
---|---|
256 - 65535 | Green color value |
1 - 255 | Bule color value |
65536 - 16777215 | Red color value |
Enable/disable the function of using External Switch to turn on/off the bulb. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Disable |
1 | Enable |
Enable/disable the function of using External Switch to changes the bulbs color. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 | Enable |
0 | Disable |
Reboot/save/exit Colorful mode.Note: This parameter is a set-only parameter. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Un-reboot Colorful mode. |
1 | Reboot Colorful mode. |
2 | Exit Colorful mode. |
3 | Save the current Colorful mode value and then to be exited. |
Configure the Colorful mode. Size: 4 Byte, Default Value: 157483008
Setting | Description |
---|---|
0 - 31 | Colour Change Speed Level |
256 - 65535 | Cycle Count |
16777215 - 134217727 | Color Display Cycle |
134217728 - 1073741823 | Color Change Speed Option |
1073741824 - 2147483647 | Color Transition Style |
32 - 255 | Time Base of Color Change Speed |
65536 - 16777215 | Brightness |
Set the Change speed. Size: 4 Byte, Default Value: 50332416
Setting | Description |
---|---|
1 - 255 | Set the pause time of OFF. |
256 - 65535 | Set the pause time of ON. |
65536 - 16777215 | Set the speed from ON to OFF. |
16777216 - 2147483647 | Set the speed from OFF to ON. |
Color index configuration when the bulb is in Multi color mode. Size: 4 Byte, Default Value: 2003125025
Setting | Description |
---|---|
1 - 15 | Index 8 |
16 - 255 | Index 7 |
256 - 4095 | Index 6 |
4096 - 65535 | Index 5 |
65536 - 1048575 | Index 4 |
1048576 - 16777215 | Index 3 |
16777216 - 268435455 | Index 2 |
268435456 - 2147483647 | Index 1 |
To set whcih notification can be sent to the associated devices (Group 1) when the state of LED Bulb is changed. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
0 | Nothing |
1 | Hail CC |
2 | Basic CC report. |
Hardware Platform | ZM5101 |
Device Type | Light Dimmer Switch |
Network Operation | Always On Slave |
Firmware Version | HW: 98 FW: 1.05 |
Z-Wave Version | 6.51.06 |
Certification ID | ZC10-16075130 |
Z-Wave Product Id | 0x0086.0x0203.0x0062 |
Z-Wave Scene Type | Scene |
Firmware Updatable | Updatable by Consumer by RF |
Switch Type | Toggle |
Frequency | XXfrequency |
Maximum transmission power | XXantenna |