This is a
Turn the primary controller of Z-Wave network into inclusion mode, short press the products Action button that you can find on the product's housing.
Aeotec Smart Dimmer 6 is a low-cost Z-Wave Dimmer plug-in module specifically used to enable Z-Wave command and control (on/off/dim) of any plug-in tool. It can report immediate wattage consumption or kWh energy usage over a period of time. In the event of power failure, non-volatile memory retains all programmed information relating to the units operating status.Its surface has a Smart RGB LED, which can be used for indicating the output load status or strength of the wireless signal. You can configure its indication colour according to your favour.The Smart Dimmer 6 is also a security Z-Wave device and supports Over The Air (OTA) feature for the products firmware upgrade.
Reset to factory default | Press and hold the Action button that you can find on the product's housing for 20 seconds and then release. This procedure should only be used when the primary controller is inoperable. |
Inclusion | Turn the primary controller of Z-Wave network into inclusion mode, short press the products Action button that you can find on the product's housing. |
Exclusion | Turn the primary controller of Z-Wave network into exclusion mode, short press the products Action button that you can find on the product's housing. |
NIF | XXXNIF |
Wakeup | XXXWakeupDescription |
Protection | XXXProtection |
FirmwareUpdate | XXXFirmwareUpdate |
SetAssociation | XXXSetAssociation |
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 5 | Z-Wave Plus LifelineThe Basic Report CC and Hail CC (configured by parameter 80) can be sent to this association group. |
2 | 5 | The Basic Set and Switch Multilevel CC will be sent to the associated nodes in this group when the Smart Dimmer 6 receives the Basic Set or SwitchMultilevel CC from the main controller. |
Set 101-103 to default value. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
1 | Set 101-103 to default value. |
To set which report needs to be sent in Report group 1 Size: 4 Byte, Default Value: 0
Setting | Description |
---|---|
1 | Send Meter Report for Voltage |
2 | Send Meter Report for Current |
4 | Send Meter Report for Watt |
8 | Send Meter Report for kWh |
To set which report needs to be sent in Report group 2 Size: 4 Byte, Default Value: 0
Setting | Description |
---|---|
1 | Send Meter Report for Voltage |
2 | Send Meter Report for Current |
4 | Send Meter Report for Watt |
8 | Send Meter Report for kWh |
To set which report needs to be sent in Report group 3 Size: 4 Byte, Default Value: 0
Setting | Description |
---|---|
1 | Send Meter Report for Voltage |
2 | Send Meter Report for Current |
4 | Send Meter Report for Watt |
8 | Send Meter Report for kWh |
Set 111-113 to default. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
1 | Set 111-113 to default. |
The time interval of sending Report group 1 Size: 4 Byte, Default Value: 3
Setting | Description |
---|---|
1 - 2147483647 | the available range is 1 to 2147483647 seconds |
The time interval of sending Report group 2 Size: 4 Byte, Default Value: 600
Setting | Description |
---|---|
1 - 2147483647 | the available range is 1 to 2147483647 seconds |
The time interval of sending Report group 3 Size: 4 Byte, Default Value: 600
Setting | Description |
---|---|
1 - 2147483647 | the available range is 1 to 2147483647 seconds |
This parameter is used to set the Smart Dimmer to start the blinking state. Size: 2 Byte, Default Value: 3850
Setting | Description |
---|---|
1 - 255 | Specify the cycle of On/Off. |
256 - 32512 | Specify the time of Dimmer blinking. |
Configure the output load status after re-power on. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Last status. |
1 | Always On |
2 | Always Off |
Set the PartnerID Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Aeon Labs Standard Product |
1 - 255 | Others |
Enable/disable the Configuration parameters to be Locked. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Disable |
1 | Enable |
Set the Device tag for Smart Dimmer 6 Size: 2 Byte, Default Value: 0
Setting | Description |
---|---|
1 - 32767 | The available range is 1 to 32767. |
Reset the Smart Dimmer 6 Size: 4 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Reset all configuration parameters to factory default setting |
1431655765 | Reset Smart Dimmer 6 to factory default setting and exclude from the network |
When this parameter is enabled,the output Load will be turned off automatically when the Current overrun 2.6A and the time more than 2 minutes. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Disable |
1 | Enable |
Set the RGB LED color value for factory testing.Note: this is a Set-only parameter. Size: 4 Byte, Default Value: 0
Setting | Description |
---|---|
1 - 255 | Blue color value |
256 - 65280 | Green color value |
65536 - 16711680 | Red color value |
To set which notification report can be sent to associated Nodes in association Group 1 when the state of Smart Dimmers load is changed Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Send Nothing |
1 | Send Hail CC |
2 | Send Basic Report CC |
3 | Send Hail CC when using Action Button to change the output load state. |
Configure the state of LED when it is in Energy mode, Momentary indicate mode or N ight light mode. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Energy mode, the LED will follow the status (on/off) of its load |
1 | Momentary indicate mode, when the state of Dimmers load changed, The LED will follow the status (on/off) of its load, but the LED will turn off after 5 seconds if there is no any switch action. |
2 | Night light mode. |
Configure the RGB value when it is in Night light mode. Size: 4 Byte, Default Value: 1774619
Setting | Description |
---|---|
1 - 255 | Blue color value |
256 - 65280 | Green color value |
65536 - 16711680 | Red color value |
Configure the brightness level of RGB LED (0%-99%) when it is in Energy Mode/momentary indicate mode. Size: 4 Byte, Default Value: 3289650
Setting | Description |
---|---|
0 - 99 | The brightness level of Green color |
256 - 355 | The brightness level of Yellow color |
65536 - 65635 | The brightness level of Red color |
Enable or disable the parameter 91 and 92. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Disable |
1 | Enable |
The value here represents minimum change in wattage (in terms of wattage) to induce a Meter Report. Size: 2 Byte, Default Value: 25
Setting | Description |
---|---|
0 - 60000 | The available range is 0 to 60000 |
The value here represents minimum change in wattage percent (in terms of percentage) to induce a Meter Report. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 - 100 | The available range is 0 to 100% |
Hardware Platform | ZM5101 |
Device Type | Light Dimmer Switch |
Network Operation | Always On Slave |
Firmware Version | HW: 99 FW: 1.11 |
Z-Wave Version | 6.51.09 |
Certification ID | ZC10-17035455 |
Z-Wave Product Id | 0x0086.0x0103.0x0063 |
Z-Wave Scene Type | Scene |
Electric Load Type | Dimmable LEDIncandescent |
Firmware Updatable | Updatable by Consumer by RF |
Color | White |
Supported Meter Type | Electric Energy |
Frequency | XXfrequency |
Maximum transmission power | XXantenna |