This is a
1. Have Z-Wave Controller entered inclusion mode.
2. Pressing button once to enter the inclusion mode.
3. After add successful, the device will wake to receive the setting command from Z-Wave Controller about 20 seconds.
Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.
This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.
If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.
For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.
This device is a Security Enabled Z-Wave Plus Product. Z-WaveTM is a wireless communication protocol designed for home automation, specifically to remotely control applications in residential and light commercial environments. The technology uses a low-power RF radio embedded or retrofitted into home electronics devices and systems, such as lighting, home access control, entertainment systems and household appliances. This product can be included and operated in any Z-WaveTM network with other Z-WaveTM certified devices from other manufacturers and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.
This device also allows to be reset without any involvement of a Z-Wave controller. This procedure should only be used when the primary controller is inoperable.
1. Pressing button for about 5 seconds.
2. IDs are excluded and all settings will reset to factory default.
Notice: Use this procedure only in the event that the primary controller is lost or otherwise inoperable.
On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.
Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.
This device is battery operated and turned into deep sleep state most of the time to save battery life time. Communication with the device is limited. In order to communicate with the device, a static controller C is needed in the network. This controller will maintain a mailbox for the battery operated devices and store commands that can not be received during deep sleep state. Without such a controller, communication may become impossible and/or the battery life time is significantly decreased.
This device will wakeup regularly and announce the wakeup state by sending out a so called Wakeup Notification. The controller can then empty the mailbox. Therefore, the device needs to be configured with the desired wakeup interval and the node ID of the controller. If the device was included by a static controller this controller will usually perform all necessary configurations. The wakeup interval is a tradeoff between maximal battery life time and the desired responses of the device. To wakeup the device please perform the following action: There is a button on PSP05. Press the button once, the device will awake 10 seconds.
Here are a few hints for network installation if things dont work as expected.
Z-Wave devices control other Z-Wave devices. The relationship between one device controlling another device is called association. In order to control a different device, the controlling device needs to maintain a list of devices that will receive controlling commands. These lists are called association groups and they are always related to certain events (e.g. button pressed, sensor triggers, ...). In case the event happens all devices stored in the respective association group will receive the same wireless command wireless command, typically a 'Basic Set' Command.
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 8 | Z-Wave Plus Lifeline |
2 | 8 | light control |
Z-Wave products are supposed to work out of the box after inclusion, however certain configuration can adapt the function better to user needs or unlock further enhanced features.
IMPORTANT: Controllers may only allow configuring signed values. In order to set values in the range 128 ... 255 the value sent in the application shall be the desired value minus 256. For example: To set a parameter to 200 it may be needed to set a value of 200 minus 256 = minus 56. In case of a two byte value the same logic applies: Values greater than 32768 may needed to be given as negative values too.
Setting the BASIC command value to turn on the light. Size: 1 Byte, Default Value: -1
Setting | Description |
---|---|
-128 - 127 | Basic command value to turn on the light. |
PIR sensitivity setting.0 means disable the PIR motion. High sensitivity means can detected long distance,but if there is more noise signal in the environment, it will re-trigger too frequency. Size: 1 Byte, Default Value: 80
Setting | Description |
---|---|
0 - 99 | PIR sensitivity setting. |
Multisensor function switch. Size: 1 Byte, Default Value: 5
Setting | Description |
---|---|
8 | When Bit2 is 0(Enable), Are the device and the lighting in the same room? 0:In the same room(Default), 1:In the different room. |
16 | Disable delay 5 seconds to turn off the light,when door/window closed.(1:Disable, 0:Enable) |
32 | Disable auto turn off the light,after door/window opened to turn on the light.(1:Disable, 0:Enable) |
Size: 1 Byte, Default Value: 4
Setting | Description |
---|---|
2 | Enable sending motion OFF report.(0:Disable, 1:Enable) |
4 | Enable PIR suoer sensitivity mode. |
16 | Notification Type,0:Using Notification Report. 1: Using Sensor Binary Report. |
32 | Disable Multi CC in auto report.(1:Disable, 0:Enable) |
64 | Disable to report battery state when the device triggered.(1:Disable, 0:Enable) |
In the normal mode, after the PIR motion detected, setting the re-detect time.8 seconds per tick,default tick is 3(24 seconds).Setting the suitable value to prevent received the trigger signal too frequently. Also can save the battery energy. Size: 1 Byte, Default Value: 3
Setting | Description |
---|---|
1 - 127 | Re-detect time |
After turn on the light,setting the delay time to turn off the lighting when the PIR motion to turn off the lighting when the PIR motion is not detected.8 seconds per tick,default tick is 4(32 seconds). Size: 1 Byte, Default Value: 4
Setting | Description |
---|---|
0 - 127 | Delay time to turn off the lighting when the PIR motion is not detected. |
The Interval time for auto report the battery level.0 means turn off auto report battery.The default value is 12.The tick time can setting by the configuration NO.20. Size: 1 Byte, Default Value: 12
Setting | Description |
---|---|
0 - 127 | The interval time for auto report the battery level. |
The interval time for auto report each tick.Setting this configuration will effect configuration NO.1 Size: 1 Byte, Default Value: 30
Setting | Description |
---|---|
-128 - 127 | The interval time for auto report each tick. |
Dimensions | 0.0500000x0.0510000x0.0500000 mm |
Weight | 47 gr |
Hardware Platform | SD3502 |
EAN | 4251295701042 |
IP Class | IP 43 |
Voltage | 3V |
Device Type | Notification Sensor |
Network Operation | Reporting Sleeping Slave |
Z-Wave Version | 6.51.09 |
Certification ID | ZC10-16105258 |
Z-Wave Product Id | 0x013C.0x0002.0x0050 |
Frequency | Europe - 868,4 Mhz |
Maximum transmission power | 5 mW |