Philio
In Wall Single relay(1way) switch module
SKU: PAN05-1B
Quickstart
This is a
1.Put your Z-Wave controller into inclusion mode by following the instructions provided by the controller manufacturer. 2.Pressing Include button of PAN05 three times within 2 seconds will enter inclusion mode.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.What is Z-Wave?
Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.
This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.
If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.
For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.
Product Description
This in-wall switch module is a transceiver which is a security enabled device which based on Z-Wave Plus technology, and it is fully compatible with any Z-WaveTM enabled network. Mini size design let the module can easily hide itself into the wall box and that will be good for the house decoration. Since PAN05 supports Security Command Class, it can learn with Secured controller. Its functionality and supported command classes is identical when included as a secure and non-secure device. There are many kind of application by using the module to switch Load On and Off, one main application is the light control. If connect the COM terminal directly to AC Line terminal, the new smart relay calibration technology can reduce the inrush current caused by the load and let the module work perfectly with many kind of light like incandescent, fluorescent and LED light. This module can also connect to alternative power supply like DC 12V to switch on/off 12V MR-16 light.Adding to Z-WaveTM Network In the front casing, there is an on/off button with LED indicator below which is used to toggle switch on and off or carries out add, remove, reset or association. When first power applied, its LED flashes on and off alternately and repeatedly at 0.5 second intervals. It implies that it has not been assigned a node ID and start auto inclusion. Auto Inclusion The function of auto inclusion will be executed as long as the in wall switch does not have Node ID and just connect the switch to main power. Note: Auto inclusion timeout is 2 minute during which the node information of explorer frame will be emitted once every several seconds. Unlike Add function as shown in the table below, the execution of auto inclusion is free from pressing the On/Off button on the Switch.
Prepare for Installation / Reset
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.
Reset to factory default
This device also allows to be reset without any involvement of a Z-Wave controller. This procedure should only be used when the primary controller is inoperable.
Use this procedure only in the event that the primary controller is lost or otherwise inoperable.1.Pressing Include button of PAN05 three times within 2 seconds will enter inclusion mode. 2.Within 1 second, press Include button of PAN05 again for 5 seconds. 3.IDs are excluded.
Safety Warning for Mains Powered Devices
ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.
Inclusion/Exclusion
On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.
Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.
Inclusion
1.Put your Z-Wave controller into inclusion mode by following the instructions provided by the controller manufacturer. 2.Pressing Include button of PAN05 three times within 2 seconds will enter inclusion mode.Exclusion
1.Put your Z-Wave controller into exclusion mode by following the instructions provided by the controller manufacturer. 2.Pressing Include button of PAN05 three times within 2 seconds will enter exclusion mode. 3.Node ID has been excluded.Quick trouble shooting
Here are a few hints for network installation if things dont work as expected.
- Make sure a device is in factory reset state before including. In doubt exclude before include.
- If inclusion still fails, check if both devices use the same frequency.
- Remove all dead devices from associations. Otherwise you will see severe delays.
- Never use sleeping battery devices without a central controller.
- Dont poll FLIRS devices.
- Make sure to have enough mains powered device to benefit from the meshing
Association - one device controls an other device
Z-Wave devices control other Z-Wave devices. The relationship between one device controlling another device is called association. In order to control a different device, the controlling device needs to maintain a list of devices that will receive controlling commands. These lists are called association groups and they are always related to certain events (e.g. button pressed, sensor triggers, ...). In case the event happens all devices stored in the respective association group will receive the same wireless command wireless command, typically a 'Basic Set' Command.
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 1 | Z-Wave Plus LifelineThe Switch can be set to send reports to associated Z-Wave devices. It supports only one association group and the group has one node support. Group1 support SWITCH_BINARY_REPORT. For group 1, the Switch will report ON/OFF status of Relay to controller. |
Configuration Parameters
Z-Wave products are supposed to work out of the box after inclusion, however certain configuration can adapt the function better to user needs or unlock further enhanced features.
IMPORTANT: Controllers may only allow configuring signed values. In order to set values in the range 128 ... 255 the value sent in the application shall be the desired value minus 256. For example: To set a parameter to 200 it may be needed to set a value of 200 minus 256 = minus 56. In case of a two byte value the same logic applies: Values greater than 32768 may needed to be given as negative values too.
Parameter 1: Edge / Pulse / Edge-Toggle mode
Manual switch S1 and S2 can set to Edge mode or Pulse mode or Edge-Toggle mode, default value is Edge mode. Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 1 | 1Edge mode |
| 2 | 2Pulse mode |
| 3 | 3Edge-Toggle mode |
Parameter 11: Manual Switch Report mode
Whenever PAN11 is manually switch on or off, it will send BINARY_SWITCH_ REPORT to the node of group1. The default setting is Enable the function. Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | 0 : Disable |
| 1 | 1 : Enable |
Parameter 2: Restore Switch State Mode
Whenever the AC power reconnected to PAN05, it will set the switch to OffOn or Last switch state, default value is Last switch state. Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | 0 : Switch Off |
| 1 | 1 : Last Switch State |
| 2 | 2 : Switch On |
Parameter 3: Manual On/Off Mode
The On/Off function of S1S2 and learn switch can be disabled or enabled by this parameter, default value is Enable. But the learning operation wont be affected. When manual On/Off function is disabled, the RF command can only switch On but not Off. This is useful function for keeping the device in switch on state. Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | 0Disable manual On/Off |
| 1 | 1Enable manual On/Off |
Parameter 4: LED indication Mode
1. Show switch stateLED on for switch on and off for switch off. The default value is Show switch state. 2. Show night modeLED off for switch on and on for switch off. 3. One Flash modeWhen the state of switch changes, LED will be on only one second, then LED keeps off. Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 1 | 1Show switch state |
| 2 | 2Show night mode |
| 3 | 3 : One flash mode |
Parameter 5: Auto Off timer
When auto off timer is equal to 0, the auto off function will be disabled. Whenever the switch is set to on, the auto off timer begin to count down. After the timer counts to zero, PAN05 will switch off automatically. The default value is disable auto off function. Size: 2 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | 0Disable auto off function |
| 1 - 32767 | 1-0x7FFF1 ~ 32767seconds |
Parameter 6: RF Off command mode
Whenever a RF Off command is received, BASIC_SETBINARY_SWITCH_SETSWITCH_ALL_OFF, it could be interpreted as Switch OffSwitch OnSwitch Toggle, or it would be ignored. The default value is Switch Off. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | 0Switch off |
| 1 | 1Ignore |
| 2 | 2Switch toggle |
| 3 | 3Switch on |
Technical Data
| Hardware Platform | SD3502 |
| Device Type | On/Off Power Switch |
| Network Operation | Always On Slave |
| Firmware Version | HW: 1 FW: 1.12 |
| Z-Wave Version | 6.51.06 |
| Certification ID | ZC10-16025010 |
| Z-Wave Product Id | 0x013C.0x0001.0x0010 |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |
Explanation of Z-Wave specific terms
- Controller — is a Z-Wave device with capabilities to manage the network. Controllers are typically Gateways,Remote Controls or battery operated wall controllers.
- Slave — is a Z-Wave device without capabilities to manage the network. Slaves can be sensors, actuators and even remote controls.
- Primary Controller — is the central organizer of the network. It must be a controller. There can be only one primary controller in a Z-Wave network.
- Inclusion — is the process of adding new Z-Wave devices into a network.
- Exclusion — is the process of removing Z-Wave devices from the network.
- Association — is a control relationship between a controlling device and a controlled device.
- Wakeup Notification — is a special wireless message issued by a Z-Wave device to announces that is able to communicate.
- Node Information Frame — is a special wireless message issued by a Z-Wave device to announce its capabilities and functions.