Villavent
Z-Wave to Systemair HVAC Adapter
SKU: 29990
Quickstart
This is a
When the device is not added to a Z-Wave network, then triple short clicks of the inclusion button will start the inclusion.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.What is Z-Wave?
Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.
This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.
If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.
For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.
Product Description
Z-Wave to Systemair HVAC Adapter is an Z-Wave Interface adapter, which connects the Z-Wave network with the Systemair Heat Recovery Ventilation. The Systemair HVAC is a residential HRV system, which can be controlled locally by one or more UI, as well as remotely by a mobile App or a browser via Z-Wave network.
Prepare for Installation / Reset
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.
Reset to factory default
This device also allows to be reset without any involvement of a Z-Wave controller. This procedure should only be used when the primary controller is inoperable.
To do a Factory Reset the user must follow the following procedure: - Press and hold the inclusion button for 6 seconds, then - Release it, and then - Press it again and hold it for 3 secondsThe Z-Wave Adapter is indicating each phase with a different LED patternsee Operational modes and indicators in the User's Manual.
Safety Warning for Mains Powered Devices
ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.
Inclusion/Exclusion
On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.
Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.
Inclusion
When the device is not added to a Z-Wave network, then triple short clicks of the inclusion button will start the inclusion.Exclusion
When the device is already included in a Z-Wave network, then triple short clicks of the inclusion button will exclude it from that Z-Wave network.Quick trouble shooting
Here are a few hints for network installation if things dont work as expected.
- Make sure a device is in factory reset state before including. In doubt exclude before include.
- If inclusion still fails, check if both devices use the same frequency.
- Remove all dead devices from associations. Otherwise you will see severe delays.
- Never use sleeping battery devices without a central controller.
- Dont poll FLIRS devices.
- Make sure to have enough mains powered device to benefit from the meshing
Association - one device controls an other device
Z-Wave devices control other Z-Wave devices. The relationship between one device controlling another device is called association. In order to control a different device, the controlling device needs to maintain a list of devices that will receive controlling commands. These lists are called association groups and they are always related to certain events (e.g. button pressed, sensor triggers, ...). In case the event happens all devices stored in the respective association group will receive the same wireless command wireless command, typically a 'Basic Set' Command.
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | Z-Wave Plus Lifeline |
Configuration Parameters
Z-Wave products are supposed to work out of the box after inclusion, however certain configuration can adapt the function better to user needs or unlock further enhanced features.
IMPORTANT: Controllers may only allow configuring signed values. In order to set values in the range 128 ... 255 the value sent in the application shall be the desired value minus 256. For example: To set a parameter to 200 it may be needed to set a value of 200 minus 256 = minus 56. In case of a two byte value the same logic applies: Values greater than 32768 may needed to be given as negative values too.
Parameter 1: System Type
Read Only Parameter, shows what is the Type of the Systemair HVAC Unit. Size: 2 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 5 | See User Manual |
| 12 - 21 | See User Manual |
Parameter 2: Filter - Period
Read Only Parameter, shows how long the filter can be used in steps of 30 days. Example 6 = 180 days. Size: 2 Byte, Default Value: 12
| Setting | Description |
|---|---|
| 6 | x 30 = 180 days |
| 9 | x 30 = 270 days |
| 12 | x 30 = 360 days |
| 15 | x 30 = 450 days |
Parameter 3: Filter - Days Used
Read Only Parameter, shows how many days the filter has been used since the last change. The value can be used to calculate the Filter remaining time by the equation: Filter Remaining Days = (Parameter_2 x 30) - Parameter_3 Size: 2 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 500 | The counter stops on 500 |
Parameter 4: Boost Mode Remaining Time
Read Only Parameter, shows how many seconds are left for Boost mode. Size: 2 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 240 - 0 | Counts down while Boost mode is active |
Parameter 5: Temperature Setpoint Step
Read Only Parameter, shows the min change available in degrees Celsius x 10. Example 25 = 2.5 degree Celsius. Size: 2 Byte, Default Value: 10
| Setting | Description |
|---|---|
| 10 | /10 = 1.0 degrees Celsius step |
| 25 | /10 = 2.5 degrees Celsius setp |
Parameter 6: CDx New Firmware Version Available
Shows the Firmware Version available in the Z-Wave adapter for the Firmware Target 2. This parameter must be written after successful uploading of the firmware image for the local UI. Example UI Version 5.02.03:MSB - x, don't care,Next - 05,Next - 02,LSB - 03. Size: 4 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 16777215 | max version 255.255.255 |
Parameter 7: PCU-ECx New Firmware Version Available
Shows the Firmware Version available in the Z-Wave adapter for the Firmware Target 1. This parameter must be written after successful uploading of the firmware image for the Ventilation Unit. Example Ventilation Unit Version 6.07.08:MSB - x, don't care,Next - 06,Next - 07,LSB - 08. Size: 4 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 16777215 | max version 255.255.255 |
Technical Data
| Hardware Platform | ZM5202 |
| Device Type | Thermostat - HVAC |
| Network Operation | Always On Slave |
| Firmware Version | HW: 2 FW: 0.01:00.80:36.80:16.00 |
| Z-Wave Version | 6.51.06 |
| Certification ID | ZC10-16065101 |
| Z-Wave Product Id | 0x0276.0x0139.0x0001 |
| Thermostat Modes | Auto ChangeoverAway |
| Thermostat Power Source | Mains powered (120V/240V) |
| Firmware Updatable | Updatable by Consumer by RF |
| Thermostat HVAC Systems Supported | Humidity ControlVentilation Control |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |
Explanation of Z-Wave specific terms
- Controller — is a Z-Wave device with capabilities to manage the network. Controllers are typically Gateways,Remote Controls or battery operated wall controllers.
- Slave — is a Z-Wave device without capabilities to manage the network. Slaves can be sensors, actuators and even remote controls.
- Primary Controller — is the central organizer of the network. It must be a controller. There can be only one primary controller in a Z-Wave network.
- Inclusion — is the process of adding new Z-Wave devices into a network.
- Exclusion — is the process of removing Z-Wave devices from the network.
- Association — is a control relationship between a controlling device and a controlled device.
- Wakeup Notification — is a special wireless message issued by a Z-Wave device to announces that is able to communicate.
- Node Information Frame — is a special wireless message issued by a Z-Wave device to announce its capabilities and functions.