Hank
Smart Switch
SKU: HKZW-SW01
Quickstart
This is a
1) Connect the power supply.2) Set the Z-Wave network main controller into learning mode (see Z-Wave network controller operating manual).3) Triple click the Z-Button, LED indicator should blink fast4) Smart Switch should be recognized and included into the Z-Wave network.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.What is Z-Wave?
Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.
This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.
If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.
For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.
Product Description
Smart Switch is a Z-Wave Switch module specifically used to enable Z-Wave command and control (on/off) of any connected device such as bulbs.
Prepare for Installation / Reset
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.
Reset to factory default
This device also allows to be reset without any involvement of a Z-Wave controller. This procedure should only be used when the primary controller is inoperable.
1) Power on the Switch.2) Press and hold the Z-button for more than 20 seconds.3) If holding time more than one second, the LED will blink faster and faster. If holding time more than 20 seconds, the LED indicator will be on for 3 seconds, which indicates that the reset is complete, then it will blink slowly indicating that it is not a part of a Z-Wave network.Use this procedure only in the event that the network primary controller is missing or otherwise inoperable.
Safety Warning for Mains Powered Devices
ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.
Inclusion/Exclusion
On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.
Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.
Inclusion
1) Connect the power supply.2) Set the Z-Wave network main controller into learning mode (see Z-Wave network controller operating manual).3) Triple click the Z-Button, LED indicator should blink fast4) Smart Switch should be recognized and included into the Z-Wave network.Exclusion
1) Connect the power supply.2) Set the Z-Wave network controller into the remove mode (see Z-Wave controller operating manual)3) Triple click the Z-button.Quick trouble shooting
Here are a few hints for network installation if things dont work as expected.
- Make sure a device is in factory reset state before including. In doubt exclude before include.
- If inclusion still fails, check if both devices use the same frequency.
- Remove all dead devices from associations. Otherwise you will see severe delays.
- Never use sleeping battery devices without a central controller.
- Dont poll FLIRS devices.
- Make sure to have enough mains powered device to benefit from the meshing
Association - one device controls an other device
Z-Wave devices control other Z-Wave devices. The relationship between one device controlling another device is called association. In order to control a different device, the controlling device needs to maintain a list of devices that will receive controlling commands. These lists are called association groups and they are always related to certain events (e.g. button pressed, sensor triggers, ...). In case the event happens all devices stored in the respective association group will receive the same wireless command wireless command, typically a 'Basic Set' Command.
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | Z-Wave Plus LifelineSmart Switch will send basic report to the associated nodes whenever it is turned on or off |
Configuration Parameters
Z-Wave products are supposed to work out of the box after inclusion, however certain configuration can adapt the function better to user needs or unlock further enhanced features.
IMPORTANT: Controllers may only allow configuring signed values. In order to set values in the range 128 ... 255 the value sent in the application shall be the desired value minus 256. For example: To set a parameter to 200 it may be needed to set a value of 200 minus 256 = minus 56. In case of a two byte value the same logic applies: Values greater than 32768 may needed to be given as negative values too.
Parameter 21: Setting device status after power failure
Define how the Smart Switch reacts after the power supply is back on.
Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Smart Switch memorizes its state after a power failure |
| 1 | Smart Switch will be on after the power supply is reconnected. |
| 2 | Smart Switch will be off after the power supply is reconnected. |
Parameter 24: Notification when Load status change
Smart Switch can send notifications to association device (Group Lifeline) when state of Smart Switchs load is changed.
Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | The function is disabled. |
| 1 | Send Basic report. |
| 2 | Send Basic report only when Load condition is not changed by Z-WAVE Command. |
Parameter 27: Indicator modes
After Smart Switch being included into a Z-Wave network, the LED in the device will indicator the state of load.
Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | The LED will follow the status (on/off) of its load. |
| 1 | When the state of Smart Switchs load changed, The LED will follow the status (on/off) of its load, but the red LED will turn off after 5 seconds if there is no more switch action. |
Technical Data
| Hardware Platform | ZM5202 |
| Device Type | On/Off Power Switch |
| Network Operation | Always On Slave |
| Firmware Version | HW: 1 FW: 1.03 |
| Z-Wave Version | 6.51.07 |
| Certification ID | ZC10-16085169 |
| Z-Wave Product Id | 0x0208.0x0101.0x0003 |
| Firmware Updatable | Updatable by Consumer by RF |
| Color | White |
| Electric Load Type | FluorescentIncandescentInductive (e.g. Motor)LED |
| Neutral Wire Required | ok |
| Switch Type | Decorator Paddle Rocker |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |
Explanation of Z-Wave specific terms
- Controller — is a Z-Wave device with capabilities to manage the network. Controllers are typically Gateways,Remote Controls or battery operated wall controllers.
- Slave — is a Z-Wave device without capabilities to manage the network. Slaves can be sensors, actuators and even remote controls.
- Primary Controller — is the central organizer of the network. It must be a controller. There can be only one primary controller in a Z-Wave network.
- Inclusion — is the process of adding new Z-Wave devices into a network.
- Exclusion — is the process of removing Z-Wave devices from the network.
- Association — is a control relationship between a controlling device and a controlled device.
- Wakeup Notification — is a special wireless message issued by a Z-Wave device to announces that is able to communicate.
- Node Information Frame — is a special wireless message issued by a Z-Wave device to announce its capabilities and functions.