Hank
Multisensor
SKU: HKZW-MS01
Quickstart
This is a
2.Add for inclusion (non-security):1) Insert two CR123A batteries.2) Set the Z-Wave network main controller into learning mode (see Z-Wave network controller operating manual).3) Triple clicking the Z-button.4) If the inclusion is successful, the LED will blink less than 5 seconds and then keep on for 3 seconds, otherwise the LED will blink 5 seconds and then turn off, in which you need to repeat the process from step 2.Add for inclusion (security): 1) Insert two CR123A batteries.2) Set the Z-Wave network main controller into learning mode (see Z-Wave network controller operating manual).3) Press and hold the Z-button for 3 seconds.4) If the inclusion is successful, the LED will blink fast for less than 5 seconds and then keep on for 3 seconds, otherwise the LED will blink fast for 5 seconds and then turn off, in which you need to repeat the process from step 2.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.What is Z-Wave?
Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.
This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.
If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.
For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.
Product Description
Multisensor is a universal Z-Wave device. Along with detecting motion the device measures the temperature, humidity and luminance . It can communicate with associated Z-Wave devices, such as Siren, Smart Switch, etc.
Prepare for Installation / Reset
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.
Reset to factory default
This device also allows to be reset without any involvement of a Z-Wave controller. This procedure should only be used when the primary controller is inoperable.
Press and hold the Z-button for 20 seconds,Multisensor will send Device_Reset_Locally to the main controller and exclude from the Z-Wave network when the Z-Button is released, this procedure will reset the Sensor to factory default.Please include a request to use the reset procedure only when the primary controller is missing or inoperable.
Inclusion/Exclusion
On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.
Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.
Inclusion
2.Add for inclusion (non-security):1) Insert two CR123A batteries.2) Set the Z-Wave network main controller into learning mode (see Z-Wave network controller operating manual).3) Triple clicking the Z-button.4) If the inclusion is successful, the LED will blink less than 5 seconds and then keep on for 3 seconds, otherwise the LED will blink 5 seconds and then turn off, in which you need to repeat the process from step 2.Add for inclusion (security): 1) Insert two CR123A batteries.2) Set the Z-Wave network main controller into learning mode (see Z-Wave network controller operating manual).3) Press and hold the Z-button for 3 seconds.4) If the inclusion is successful, the LED will blink fast for less than 5 seconds and then keep on for 3 seconds, otherwise the LED will blink fast for 5 seconds and then turn off, in which you need to repeat the process from step 2.Exclusion
Remove for exclusion;1.Insert two CR123A batteries.2.Set the Z-Wave network main controller into removing mode (see Z-Wave controller operating manual).3.Triple clicking the Z-button.4.If the removing is successful, the LED will blink slowly for 5 seconds and then turn off, otherwise you need to repeat the process from step 2.Quick trouble shooting
Here are a few hints for network installation if things dont work as expected.
- Make sure a device is in factory reset state before including. In doubt exclude before include.
- If inclusion still fails, check if both devices use the same frequency.
- Remove all dead devices from associations. Otherwise you will see severe delays.
- Never use sleeping battery devices without a central controller.
- Dont poll FLIRS devices.
- Make sure to have enough mains powered device to benefit from the meshing
Association - one device controls an other device
Z-Wave devices control other Z-Wave devices. The relationship between one device controlling another device is called association. In order to control a different device, the controlling device needs to maintain a list of devices that will receive controlling commands. These lists are called association groups and they are always related to certain events (e.g. button pressed, sensor triggers, ...). In case the event happens all devices stored in the respective association group will receive the same wireless command wireless command, typically a 'Basic Set' Command.
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | 1. Notification Report.Sensor will send Notification Report to the associated nodes when Multisensor is removed or/and PIR is triggered.2. Sensor Multilevel Report.Multisensor will send Sensor Multilevel Report to the associated nodes at setting interval.3. Battery Report.Multisensor will send Battery Report when the battery level is low and the battery reports value is 0xFF.4. Device Reset Locally Notification. |
| 2 | 5 | 1. Basic SetMultisensor will send Basic Set to associated nodes when the PIR is triggered. |
Configuration Parameters
Z-Wave products are supposed to work out of the box after inclusion, however certain configuration can adapt the function better to user needs or unlock further enhanced features.
IMPORTANT: Controllers may only allow configuring signed values. In order to set values in the range 128 ... 255 the value sent in the application shall be the desired value minus 256. For example: To set a parameter to 200 it may be needed to set a value of 200 minus 256 = minus 56. In case of a two byte value the same logic applies: Values greater than 32768 may needed to be given as negative values too.
Parameter 12: MOTION SENSORS SENSITIVITY.
The higher the value is set, the more sensitive the PIR sensor are.
Size: 1 Byte, Default Value: 8
| Setting | Description |
|---|---|
| 1 - 8 | Level 0 to 8 |
| 0 | Disabled |
Parameter 13: MOTION SENSORS BLIND TIME (INSENSITIVITY)
Period of time through which the PIR sensor is blind (insensitive) to motion. After this time period the PIR sensor will be again able to detect motion. The longer the insensitivity period, the longer the battery life. If the sensor is required to detect motion quickly, the time period may be shortened.
Size: 2 Byte, Default Value: 30
| Setting | Description |
|---|---|
| 1 - 60 | blink time is 1 to 60 |
Parameter 14: ENABLE/DISABLE BASIC COMMAND
Multisensor can send BASIC ON/OFF COMMAND CLASS to nodes associated with group 2.
Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Disable |
| 1 | Enable |
Parameter 15: BASIC COMMAND VALUE
Multisensor can reverse the BASIC ON/OFF.
Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Detecting motion: BASIC ON, motion alarm cancellation: BASIC OFF. |
| 1 | Detecting motion: BASIC OFF, motion alarm cancellation: BASIC ON. |
Parameter 170: No.170 SET PARAMETER 171174 TO DEFAULT SETTINGS
Set parameter 171,172,173,174 to default settings
Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 85 | Set parameter 171,172,173,174 to default settings |
Parameter 171: BATTERY REPORT INTERVAL
The interval of sending battery report to association device (Group Lifeline). The reportsare sent even if there are no changes in the battery level.
Size: 4 Byte, Default Value: 1800
| Setting | Description |
|---|---|
| 5 - 2678400 | The interval of sending battery report |
Parameter 172: TEMPERATURE REPORT INTERVAL
The interval of sending temperature report to association device (Group Lifeline). The reportsare sent even if there are no changes in the temperature level.
Size: 4 Byte, Default Value: 1800
| Setting | Description |
|---|---|
| 5 - 2678400 | The interval of sending temperature report |
Parameter 173: HUMIDITY REPORT INTERVAL
The interval of sending Humidity report to association device (Group Lifeline). The reportsare sent even if there are no changes in the humidity level.
Size: 4 Byte, Default Value: 1800
| Setting | Description |
|---|---|
| 5 - 2678400 | The interval of sending Humidity report |
Parameter 174: LUMINANCE REPORT INTERVAL
The interval of sending luminance report to association device (Group Lifeline). The reportsare sent even if there are no changes in the luminance level.
Size: 4 Byte, Default Value: 1800
| Setting | Description |
|---|---|
| 5 - 2678400 | The interval of sending luminance report |
Parameter 181: BATTERY REPORT THRESHOLD
The parameter determines the change in battery level resulting in battery report being sent to the main controller.
Size: 1 Byte, Default Value: 10
| Setting | Description |
|---|---|
| 0 - 100 | the change in battery level resulting in battery report being sent to the main controller. |
Parameter 182: TEMPERATURE REPORT THRESHOLD
The parameter determines the change in temperature level resulting in temperature report being sent to the main controller.(Degrees Celsius)
Size: 1 Byte, Default Value: 20
| Setting | Description |
|---|---|
| 0 | reports are not sent |
| 1 - 255 | the change in temperature level resulting in temperature report being sent to the main controller. |
Parameter 183: HUMITIDY REPORT THRESHOLD
The parameter determines the change in humidity level resulting in humidity report being sent to the main controller.
Size: 1 Byte, Default Value: 5
| Setting | Description |
|---|---|
| 0 | reports are not sent |
| 1 - 255 | the change in humidity level resulting in humidity report being sent to the main controller. |
Parameter 184: LUMINANCE REPORT THRESHOLD
The parameter determines the change in luminance level resulting in luminance report being sent to the main controller.
Size: 2 Byte, Default Value: 200
| Setting | Description |
|---|---|
| 0 | Reports are not sent |
| 1 - 65535 | the change in luminance level resulting in luminance report being sent to the main controller. |
Parameter 32: LEVEL OF LOW BATTERY
Define a battery level as the low battery.
Size: 1 Byte, Default Value: 20
| Setting | Description |
|---|---|
| 10 - 50 | The low level from 10% to 50% |
Technical Data
| Hardware Platform | ZM5101 |
| Device Type | Notification Sensor |
| Network Operation | Reporting Sleeping Slave |
| Firmware Version | HW: 1 FW: 1.04 |
| Z-Wave Version | 6.51.09 |
| Certification ID | ZC10-17045529 |
| Z-Wave Product Id | 0x0208.0x0200.0x0006 |
| Sensors | HumidityLuminanceMotion/No Motion (Binary) |
| Supported Notification Types | Access Control |
| Firmware Updatable | Updatable by Consumer by RF |
| Color | White |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |
Supported Command Classes
- Association Grp Info
- Association V2
- Battery
- Configuration
- Device Reset Locally
- Firmware Update Md V2
- Manufacturer Specific V2
- Notification V5
- Powerlevel
- Security
- Sensor Multilevel V5
- Version V2
- Wake Up V2
- Zwaveplus Info V2
Controlled Command Classes
- Basic
Explanation of Z-Wave specific terms
- Controller — is a Z-Wave device with capabilities to manage the network. Controllers are typically Gateways,Remote Controls or battery operated wall controllers.
- Slave — is a Z-Wave device without capabilities to manage the network. Slaves can be sensors, actuators and even remote controls.
- Primary Controller — is the central organizer of the network. It must be a controller. There can be only one primary controller in a Z-Wave network.
- Inclusion — is the process of adding new Z-Wave devices into a network.
- Exclusion — is the process of removing Z-Wave devices from the network.
- Association — is a control relationship between a controlling device and a controlled device.
- Wakeup Notification — is a special wireless message issued by a Z-Wave device to announces that is able to communicate.
- Node Information Frame — is a special wireless message issued by a Z-Wave device to announce its capabilities and functions.