ECO LIFE ENGINEERING
Z-WAVE AC MASTER
SKU: ZXT-600JP
Quickstart
This is a
1Refer to your primary controller to enter into the Inclusion Mode or Exclusion Mode2When it is prompted to enter it, please triple click the PROG button within 1 second.Green Indicator flashes TWICE then stay off
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.What is Z-Wave?
Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.
This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.
If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.
For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.
Product Description
ZXT-600 AC Master is a Z-Wave plus certified IR Bridge for split air conditioner control by receiving Z-Wave command and translating to Infrared command and flawlessly work with any Z-Wave compliant gateway. With its over 250 brands built-in code library and ever-green up to date cloud IR database supporting advanced code learning search, ZXT-600 can easily set up and smart control most of AC brands and models actively worldwide by Z-Wave gateway. The battery powered device will allow you to mount it anywhere you want such as wall, ceiling or put it on table and never compromise on the form factor. By supporting OTA function, gateway can enable ZXT-600 to update firmware if newest available.
Prepare for Installation / Reset
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.
Reset to factory default
This device also allows to be reset without any involvement of a Z-Wave controller. This procedure should only be used when the primary controller is inoperable.
Press and Hold PROG button for 3 seconds on AC Master, the Green Indicator will light up. DO NOT Release the PROG Button until Green Indicator flashes TWICE.Remark : All the Setting and Data will be permanently deleted.Please use this procedure only when the network primary controller is missing or otherwise inoperable.
Inclusion/Exclusion
On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.
Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.
Inclusion
1Refer to your primary controller to enter into the Inclusion Mode or Exclusion Mode2When it is prompted to enter it, please triple click the PROG button within 1 second.Green Indicator flashes TWICE then stay offExclusion
1Refer to your primary controller to enter into the Inclusion Mode or Exclusion Mode2When it is prompted to enter it, please triple click the PROG button within 1 second.Green Indicator flashes TWICE then stay offQuick trouble shooting
Here are a few hints for network installation if things dont work as expected.
- Make sure a device is in factory reset state before including. In doubt exclude before include.
- If inclusion still fails, check if both devices use the same frequency.
- Remove all dead devices from associations. Otherwise you will see severe delays.
- Never use sleeping battery devices without a central controller.
- Dont poll FLIRS devices.
- Make sure to have enough mains powered device to benefit from the meshing
Association - one device controls an other device
Z-Wave devices control other Z-Wave devices. The relationship between one device controlling another device is called association. In order to control a different device, the controlling device needs to maintain a list of devices that will receive controlling commands. These lists are called association groups and they are always related to certain events (e.g. button pressed, sensor triggers, ...). In case the event happens all devices stored in the respective association group will receive the same wireless command wireless command, typically a 'Basic Set' Command.
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 1 | Association Group #1 (max. 1 node) is default to associate with the primary controller (Gateway/Hub/Controller) for AC Master Status change report, refer to below for report details: a) Current Room Temperature (report in precision of 0.5C or 1F) (It will be according to Configuration Parameter 39 setting to decide the trigger level) b) Current Battery Level (Only apply in Low Battery Warning happened) c) Device Reset Locally Notification (Only report when the AC Master has been triggered the RESET TO DEFAULT) |
Configuration Parameters
Z-Wave products are supposed to work out of the box after inclusion, however certain configuration can adapt the function better to user needs or unlock further enhanced features.
IMPORTANT: Controllers may only allow configuring signed values. In order to set values in the range 128 ... 255 the value sent in the application shall be the desired value minus 256. For example: To set a parameter to 200 it may be needed to set a value of 200 minus 256 = minus 56. In case of a two byte value the same logic applies: Values greater than 32768 may needed to be given as negative values too.
Parameter 25: Learn IR Code
Default: 0x00range: (0x0000 to 0x20)refer to learning mapping table
Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 32 | Storage Location |
Parameter 26: Check IR Code Learning Status
Default: 0x00range: 0 to 4 (0x00 to 0x04)0(0x00) : Idle - IR Channel is idle1(0x01) : OK - the last learning operation was completed successfully2(0x02) : Learning - ZXT-600 is busy processing previous learning request3(0x03) : FullAll locations are being used.4(0x04) : The last learning request was failedNote:The status value 0x01 and 0x04 will be reset to 0x00 after ZXT-600 receives a get command to this parameter.
Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 4 | IR Code Learning Status |
Parameter 27: Set IR Code number from built-in code library
Refer to Code Finder Webpage
Size: 2 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 1150 | IR Code Number |
Parameter 30: Set Auto Report Condition Trigger By Room Temperature change
0(0x00) = Disable (Default)(for saving battery life)Auto report if room temperature is different from last report.1(0x01) = 1F (0.5C)2(0x02) = 2F (1C) 3(0x03) = 3F (1.5C)4(0x04) = 4F (2C)5(0x05) = 5F (2.5C)6(0x06) = 6F (3C)7(0x07) = 7F (3.5C)8(0x08) = 8F (4C)
Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 8 | Room Temperature Change |
Parameter 32: Set Built-in IR Emitter Control
Default: 0xFF0 or 255(0x00 or 0xFF)0(0x00): Disable255(0xFF): Enable (Default)
Size: 1 Byte, Default Value: 255
| Setting | Description |
|---|---|
| 0 | Disable |
| 255 | Enable |
Parameter 33: SWING Function
Default: 0x01Range 0 to 1 (0x00 or 0x01)0(0x00) : Swing OFF1(0x01) : Swing Auto (Default)
Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | SWING OFF |
| 1 | SWING Auto |
Parameter 34: Set Auto Report Condition By Time Interval
Auto report by the following time interval.1(0x01) = 1 Hr2(0x02) = 2 Hrs3(0x03) = 3 Hrs4(0x04) = 4 Hrs5(0x05) = 5 Hrs6(0x06) = 6 Hrs7(0x07) = 7 Hrs8(0x08) = 8 Hrs (Default)
Size: 1 Byte, Default Value: 8
| Setting | Description |
|---|---|
| 0 - 8 | Time Interval |
Parameter 37: Calibrate temperature reading
Temperature offset value.0(0x00) = 0C (Default)1(0x01) = 1C2(0x02) = 2C3(0x03) = 3C4(0x04) = 4C5(0x05) = 5C255(0xFF) = -1C254(0xFE) = -2C253(0xFD) = -3C252(0xFC) = -4C251(0xFB) = -5C
Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 5 | Positive Range |
| 251 - 255 | Negative Range |
Technical Data
| Hardware Platform | ZM5202 |
| Device Type | Thermostat - HVAC |
| Network Operation | Listening Sleeping Slave |
| Firmware Version | HW: 3 FW: 1.03:01.07:171.06 |
| Z-Wave Version | 6.61.00 |
| Certification ID | ZC10-18036053 |
| Z-Wave Product Id | 0x037C.0x0109.0x8490 |
| Sensors | Target Temperature |
| Color | White |
| Thermostat HVAC Systems Supported | |
| Thermostat Modes | AutoAwayCoolDry AirFan OnlyHeatResume |
| Firmware Updatable | Updatable by Consumer by RF |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |
Supported Command Classes
- Application Status
- Association Grp Info V3
- Association V2
- Basic
- Battery
- Configuration V2
- Device Reset Locally
- Firmware Update Md V3
- Manufacturer Specific V2
- Powerlevel
- Security
- Sensor Multilevel V7
- Thermostat Fan Mode V4
- Thermostat Mode V3
- Thermostat Setpoint V3
- Version V2
- Zwaveplus Info V2
Explanation of Z-Wave specific terms
- Controller — is a Z-Wave device with capabilities to manage the network. Controllers are typically Gateways,Remote Controls or battery operated wall controllers.
- Slave — is a Z-Wave device without capabilities to manage the network. Slaves can be sensors, actuators and even remote controls.
- Primary Controller — is the central organizer of the network. It must be a controller. There can be only one primary controller in a Z-Wave network.
- Inclusion — is the process of adding new Z-Wave devices into a network.
- Exclusion — is the process of removing Z-Wave devices from the network.
- Association — is a control relationship between a controlling device and a controlled device.
- Wakeup Notification — is a special wireless message issued by a Z-Wave device to announces that is able to communicate.
- Node Information Frame — is a special wireless message issued by a Z-Wave device to announce its capabilities and functions.