Zooz
S2 Multisiren
SKU: ZSE19
Quickstart
This is a
AUTO INCLUSION:1. Initiate inclusion (pairing) in the app (or web interface). Not sure how? [email protected] youre using an S2 hub, it may ask you to enter the DSK key printed on the back cover sticker to complete secure inclusion.2. Insert the batteries as instructed above (if you already did, take them out for at least 15 seconds before starting the inclusion process). The LED indicator will start blinking and the Multisiren will join the network automatically.MANUAL INCLUSION:Put your Z-Wave hub into inclusion mode and click the Z-Wave button on the Multisiren 3 times quickly.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.What is Z-Wave?
Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.
This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.
If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.
For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.
Product Description
FEATURES:- Audio and visual alarm triggered by other Z-Wave devices- Configurable siren alarm duration- Built-in temperature and humidity sensor (if Multilevel Sensor is supported)- Audio Speaker for custom sound playback (if Sound Switch is supported)- S2 security protocol and the latest 500 Z-Wave chip for faster and safer wireless communication- Tamper protection, low-battery alertsSPECS:- Model Number: ZSE19- Z-Wave Signal Frequency: 908.42 MHz- Power: 4 x LR14 (C Cell) battery- Range: Up to 100 feet line of sight- Operating Temperature: 14-104 F (-10-40 C)- Operating Humidity: 0-80%- Installation and Use: Indoor only
Prepare for Installation / Reset
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.
Reset to factory default
This device also allows to be reset without any involvement of a Z-Wave controller. This procedure should only be used when the primary controller is inoperable.
If your primary controller is missing or inoperable, you may need to reset the device to factory settings. To complete the reset process manually, make sure the Multisiren is powered, then CLICK-CLICK-CLICKCLICKNHOLD the Z-Wave button for AT LEAST 5 SECONDS. The LED indicator will flash to confirm successful reset. NOTE: All previously recorded activity and custom settings will be erased from the devices memory.
Inclusion/Exclusion
On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.
Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.
Inclusion
AUTO INCLUSION:1. Initiate inclusion (pairing) in the app (or web interface). Not sure how? [email protected] youre using an S2 hub, it may ask you to enter the DSK key printed on the back cover sticker to complete secure inclusion.2. Insert the batteries as instructed above (if you already did, take them out for at least 15 seconds before starting the inclusion process). The LED indicator will start blinking and the Multisiren will join the network automatically.MANUAL INCLUSION:Put your Z-Wave hub into inclusion mode and click the Z-Wave button on the Multisiren 3 times quickly.Exclusion
1. Bring the Multisiren within direct range of your Z-Wave gateway (hub).2. Put the Z-Wave hub into exclusion mode (not sure how to do that? [email protected]).3. Click the Z-Wave button on the Multisiren 3 times quickly to finalize the process.4. Your hub will confirm exclusion and the device will disappear from your controller's device list.Quick trouble shooting
Here are a few hints for network installation if things dont work as expected.
- Make sure a device is in factory reset state before including. In doubt exclude before include.
- If inclusion still fails, check if both devices use the same frequency.
- Remove all dead devices from associations. Otherwise you will see severe delays.
- Never use sleeping battery devices without a central controller.
- Dont poll FLIRS devices.
- Make sure to have enough mains powered device to benefit from the meshing
Association - one device controls an other device
Z-Wave devices control other Z-Wave devices. The relationship between one device controlling another device is called association. In order to control a different device, the controlling device needs to maintain a list of devices that will receive controlling commands. These lists are called association groups and they are always related to certain events (e.g. button pressed, sensor triggers, ...). In case the event happens all devices stored in the respective association group will receive the same wireless command wireless command, typically a 'Basic Set' Command.
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | Z-Wave Plus Lifeline |
Configuration Parameters
Z-Wave products are supposed to work out of the box after inclusion, however certain configuration can adapt the function better to user needs or unlock further enhanced features.
IMPORTANT: Controllers may only allow configuring signed values. In order to set values in the range 128 ... 255 the value sent in the application shall be the desired value minus 256. For example: To set a parameter to 200 it may be needed to set a value of 200 minus 256 = minus 56. In case of a two byte value the same logic applies: Values greater than 32768 may needed to be given as negative values too.
Parameter 1: Siren Alarm Duration
Choose how long you want the siren alarm to last for once its triggered. The number entered as value corresponds to the number of seconds. Size: 2 Byte, Default Value: 180
| Setting | Description |
|---|---|
| 10 - 600 | seconds (alarm duration time) |
Parameter 2: Temperature and Humidity Reporting Interval
Choose how often you want the Multisiren to report temperatureand humidity readings to the hub. The number entered as value corresponds to the number of minutes. Frequent reports will decrease battery life. Size: 2 Byte, Default Value: 30
| Setting | Description |
|---|---|
| 1 - 1440 | minutes (reporting interval) |
Parameter 3: Custom Sound Selection for Audio Speaker
Enable one of the custom sounds in the audio file library. Thenumber entered as value corresponds to the file number in the library. This setting is to be used only is the new Sound Switch command class is not yet included in your controller's command class library and incorporated in the home automation interface. It's recommended that the Audio Speaker function is managed by the Sound Switch command class. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | pause (no sound) |
| 1 - 99 | sound (file) number in the library to be triggered |
Technical Data
| Hardware Platform | SD3502 |
| Device Type | Siren |
| Network Operation | Listening Sleeping Slave |
| Firmware Version | HW: 1 FW: 1.02:00.01 |
| Z-Wave Version | 6.71.03 |
| Certification ID | ZC10-18106268 |
| Z-Wave Product Id | 0x027A.0x000C.0x0003 |
| Color | White |
| Sensors | Air TemperatureHumidity |
| Supported Notification Types | Siren |
| Security V2 | S2_UNAUTHENTICATED ,S2_AUTHENTICATED |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |
Supported Command Classes
- Association Grp Info
- Association V2
- Basic
- Battery
- Configuration
- Device Reset Locally
- Firmware Update Md V4
- Manufacturer Specific V2
- Notification V8
- Powerlevel
- Security
- Security 2
- Sensor Multilevel V5
- Sound Switch
- Supervision
- Switch Binary
- Transport Service V2
- Version V3
- Zwaveplus Info V2
Explanation of Z-Wave specific terms
- Controller — is a Z-Wave device with capabilities to manage the network. Controllers are typically Gateways,Remote Controls or battery operated wall controllers.
- Slave — is a Z-Wave device without capabilities to manage the network. Slaves can be sensors, actuators and even remote controls.
- Primary Controller — is the central organizer of the network. It must be a controller. There can be only one primary controller in a Z-Wave network.
- Inclusion — is the process of adding new Z-Wave devices into a network.
- Exclusion — is the process of removing Z-Wave devices from the network.
- Association — is a control relationship between a controlling device and a controlled device.
- Wakeup Notification — is a special wireless message issued by a Z-Wave device to announces that is able to communicate.
- Node Information Frame — is a special wireless message issued by a Z-Wave device to announce its capabilities and functions.