Zooz
Z-Wave Plus Double Plug
SKU: ZW47
Quickstart
This is a
Inclusion the ZW47 from the existing Z-Wave home control network with your primary controller.---Refer to your primary controller instructions to process the inclusion / exclusion setup procedure.---When prompted by your primary controller, click the PROG button Three times in one second.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.What is Z-Wave?
Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.
This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.
If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.
For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.
Product Description
It is smart plug type device controlled by Z-Wave controller and can be configured in Z-Wave sensor network, if Z-Wave certified controller features remote access, you can dim lights at home from your mobile phone separately, and manual dim light by push button .
Prepare for Installation / Reset
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.
Reset to factory default
This device also allows to be reset without any involvement of a Z-Wave controller. This procedure should only be used when the primary controller is inoperable.
Press the button twice quickly and then press and hold the button 10S.device will resetPlease use this procedure only when the network primary controller is missing or otherwise inoperable
Safety Warning for Mains Powered Devices
ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.
Inclusion/Exclusion
On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.
Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.
Inclusion
Inclusion the ZW47 from the existing Z-Wave home control network with your primary controller.---Refer to your primary controller instructions to process the inclusion / exclusion setup procedure.---When prompted by your primary controller, click the PROG button Three times in one second.Exclusion
Exclusion the ZW47 from the existing Z-Wave home control network with your primary controller.---Refer to your primary controller instructions to process the inclusion / exclusion setup procedure.---When prompted by your primary controller, click the PROG button Three times in one second.Quick trouble shooting
Here are a few hints for network installation if things dont work as expected.
- Make sure a device is in factory reset state before including. In doubt exclude before include.
- If inclusion still fails, check if both devices use the same frequency.
- Remove all dead devices from associations. Otherwise you will see severe delays.
- Never use sleeping battery devices without a central controller.
- Dont poll FLIRS devices.
- Make sure to have enough mains powered device to benefit from the meshing
Association - one device controls an other device
Z-Wave devices control other Z-Wave devices. The relationship between one device controlling another device is called association. In order to control a different device, the controlling device needs to maintain a list of devices that will receive controlling commands. These lists are called association groups and they are always related to certain events (e.g. button pressed, sensor triggers, ...). In case the event happens all devices stored in the respective association group will receive the same wireless command wireless command, typically a 'Basic Set' Command.
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 1 | Z-Wave Plus Lifeline |
| 2 | 5 | basic set commandWhen the output of the ZW47 Enpoint1 socket is changed, On (0xFF) or Off (0x00)orOverload, The ZW47 will automatically send out a relatedbasic set command. On (0xFF) or Off (0x00) to its associated group. |
| 3 | 5 | basic set commandWhen the output of the ZW47 Enpoint2 socket is changed, On (0xFF) or Off (0x00)orOverload, The ZW47 will automatically send out a relatedbasic set command. On (0xFF) or Off (0x00) to its associated group. |
Configuration Parameters
Z-Wave products are supposed to work out of the box after inclusion, however certain configuration can adapt the function better to user needs or unlock further enhanced features.
IMPORTANT: Controllers may only allow configuring signed values. In order to set values in the range 128 ... 255 the value sent in the application shall be the desired value minus 256. For example: To set a parameter to 200 it may be needed to set a value of 200 minus 256 = minus 56. In case of a two byte value the same logic applies: Values greater than 32768 may needed to be given as negative values too.
Parameter 1: Restores state after power failure
Restores state after power failure Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | The state before a power outage. |
| 1 | outlet on |
| 2 | outlet off |
Parameter 10: Endpoint1 Enable Auto Turn-ON Timer
Endpoint1 Enable Auto Turn-ON Timer Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | EP1 Auto Turn-ON Timer Disabled |
| 1 | EP1 Auto Turn-ON Timer Enabled |
Parameter 11: Endpoint1 Count Down Configuration(Turn on the output by time
Endpoint1 Count Down Configuration(Turn on the output by time Size: 4 Byte, Default Value: 60
| Setting | Description |
|---|---|
| 1 - 65535 | Endpoint1 Count Down Configuration(Turn on the output by time |
Parameter 12: Endpoint2 Enable Auto Turn-OFF Timer
Endpoint2 Enable Auto Turn-OFF Timer Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | EP2 Auto Turn-OFF Timer Disabled |
| 1 | EP2 Auto Turn-OFF Timer Enabled |
Parameter 13: Endpoint2 Count Down Configuration(Turn off the output by time
Endpoint2 Count Down Configuration(Turn off the output by time Size: 4 Byte, Default Value: 60
| Setting | Description |
|---|---|
| 1 - 65535 | Endpoint2 Count Down Configuration(Turn off the output by time |
Parameter 14: Endpoint2 Enable Auto Turn-ON Timer
`Endpoint2 Enable Auto Turn-ON Timer Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | EP2 Auto Turn-ON Timer Disabled |
| 1 | EP2 Auto Turn-ON Timer Enabled |
Parameter 15: Endpoint2 Count Down Configuration(Turn on the output by time
Endpoint2 Count Down Configuration(Turn on the output by time Size: 4 Byte, Default Value: 60
| Setting | Description |
|---|---|
| 1 - 65535 | Endpoint2 Count Down Configuration(Turn on the output by time |
Parameter 16: Manual Control
Manual Control Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | Manual Control Disabled |
| 1 | Manual Control Enabled |
Parameter 17: Status LED Configuration
Status LED Configuration Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | LED indicator will display power consumption whenever the device is plugged in |
| 1 | LED indicator will display power consumption whenever the device is ON in and will turn off when the plug is OFF |
| 2 | LED indicator will display the level of power consumption for 5 seconds only whenever the device is turned on or off |
| 3 | Always OFF |
Parameter 2: Power Wattage Report Value Threshold(Wattage)
Power Wattage Report Value Threshold(Wattage) Size: 4 Byte, Default Value: 10
| Setting | Description |
|---|---|
| 0 - 10 | Power Wattage Report Value Threshold(Wattage) |
Parameter 4: Energy (kWh) Report Frequency (Timer)
Energy (kWh) Report Frequency (Timer) Size: 4 Byte, Default Value: 300
| Setting | Description |
|---|---|
| 30 - 2678400 | Energy (kWh) Report Frequency (Timer) |
Parameter 5: Voltage (V) Report Frequency (Timer)
Voltage (V) Report Frequency (Timer) Size: 4 Byte, Default Value: 300
| Setting | Description |
|---|---|
| 30 - 2678400 | Voltage (V) Report Frequency (Timer) |
Parameter 6: Electricity (A) Report Frequency (Timer)
Electricity (A) Report Frequency (Timer) Size: 4 Byte, Default Value: 300
| Setting | Description |
|---|---|
| 0 - 30 | Power Wattage Report Value Threshold(Wattage) |
| 30 - 2678400 | Electricity (A) Report Frequency (Timer) |
Parameter 7: Overload Protection (Current)
Overload Protection (Current) Size: 1 Byte, Default Value: 13
| Setting | Description |
|---|---|
| 1 - 16 | Overload Protection (Current) |
Parameter 8: Endpoint1 Enable Auto Turn-OFF Timer
Endpoint1 Enable Auto Turn-OFF Timer Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | EP1 Auto Turn-OFF Timer Disabled |
| 1 | EP1Auto Turn-OFF Timer Enabled |
Parameter 9: Endpoint1 Count Down Configuration(Turn off the output by time
Endpoint1 Count Down Configuration(Turn off the output by time Size: 4 Byte, Default Value: 60
| Setting | Description |
|---|---|
| 1 - 65535 | Endpoint1 Count Down Configuration(Turn off the output by time |
Technical Data
| Hardware Platform | ZM5202 |
| Device Type | On/Off Power Switch |
| Network Operation | Always On Slave |
| Firmware Version | HW: 255 FW: 1.00 |
| Z-Wave Version | 6.71.03 |
| Certification ID | ZC10-18116324 |
| Z-Wave Product Id | 0x0312.0xA000.0xA003 |
| Electric Load Type | FluorescentIncandescentInductive (e.g. Motor)LED |
| Color | White |
| Supported Meter Type | Electric Energy |
| Firmware Updatable | Updatable by Consumer by RF |
| Supported Notification Types | Power Management |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |
Explanation of Z-Wave specific terms
- Controller — is a Z-Wave device with capabilities to manage the network. Controllers are typically Gateways,Remote Controls or battery operated wall controllers.
- Slave — is a Z-Wave device without capabilities to manage the network. Slaves can be sensors, actuators and even remote controls.
- Primary Controller — is the central organizer of the network. It must be a controller. There can be only one primary controller in a Z-Wave network.
- Inclusion — is the process of adding new Z-Wave devices into a network.
- Exclusion — is the process of removing Z-Wave devices from the network.
- Association — is a control relationship between a controlling device and a controlled device.
- Wakeup Notification — is a special wireless message issued by a Z-Wave device to announces that is able to communicate.
- Node Information Frame — is a special wireless message issued by a Z-Wave device to announce its capabilities and functions.