Dooya
Tubular motor
SKU: DM35E/F-6/28;DM35E/F-10/17;DM35E/F-13/14
Quickstart
This is a
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.What is Z-Wave?
Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.
This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.
If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.
For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.
Product Description
Features:Percentage controlPosition feedbackElectronic LimitSwitch DirectionStall ProtectionBuilt-in ReceiverPreferred Stop PositionLow-noiseJog & Lift Mode
Prepare for Installation / Reset
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.
Safety Warning for Mains Powered Devices
ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.
Inclusion/Exclusion
On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.
Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.
Quick trouble shooting
Here are a few hints for network installation if things dont work as expected.
- Make sure a device is in factory reset state before including. In doubt exclude before include.
- If inclusion still fails, check if both devices use the same frequency.
- Remove all dead devices from associations. Otherwise you will see severe delays.
- Never use sleeping battery devices without a central controller.
- Dont poll FLIRS devices.
- Make sure to have enough mains powered device to benefit from the meshing
Association - one device controls an other device
Z-Wave devices control other Z-Wave devices. The relationship between one device controlling another device is called association. In order to control a different device, the controlling device needs to maintain a list of devices that will receive controlling commands. These lists are called association groups and they are always related to certain events (e.g. button pressed, sensor triggers, ...). In case the event happens all devices stored in the respective association group will receive the same wireless command wireless command, typically a 'Basic Set' Command.
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | GROUP 1 is lifeline service assigned to the motor position. It enables the motor to send reports to Z-Wave Controller or Z-Wave Gateway whenever the motor is starting or stopped.The Group Support: SWITCH_MULTILEVEL_REPORT_V3 DEVICE_RESET_LOCALLY_NOTIFICATION |
| 2 | 5 | GROUP 2 allows for Send Multilevel Report to associated devices in this group.This Group Support: SWITCH_MULTILEVEL_REPORT_V3 |
Configuration Parameters
Z-Wave products are supposed to work out of the box after inclusion, however certain configuration can adapt the function better to user needs or unlock further enhanced features.
IMPORTANT: Controllers may only allow configuring signed values. In order to set values in the range 128 ... 255 the value sent in the application shall be the desired value minus 256. For example: To set a parameter to 200 it may be needed to set a value of 200 minus 256 = minus 56. In case of a two byte value the same logic applies: Values greater than 32768 may needed to be given as negative values too.
Parameter 1: Motor rotation direction
This parameter is used to set the motor rotation direction.Value:Clockwise: 0Anticlockwiseset: 1 Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Clockwise |
| 1 | Anticlockwise |
Parameter 10: Delete the limit position
Delete the limit position Size: 1 Byte, Default Value: 127
| Setting | Description |
|---|---|
| 127 | Delete the limit position |
Parameter 2: Touch-start setting
This parameter is used to set the touch-start setting.Value:Enable touch-start function: 0Disable touch-start function: 1 Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Enable touch-start function |
| 1 | Disable touch-start function |
Parameter 3: Weak electric switch mode
This parameter is used to set the weak electric switch mode.Value:Double-button reboundable switch: 1Double-button non-reboundable switch: 2DC246 switch: 3Single-button cyclic switch: 4 Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 1 - 4 | Switch mode selection |
Parameter 4: Strong electric switch mode
This parameter is used to set the need for strong electric switch mode.Value:Double-button non-reboundable: 0Hotel mode: 1Double-button reboundable: 2 Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 2 | Switch mode selection |
Parameter 5: Position limits status
Position limits status (Read-only)Value:No limits: 0Limits had been set: 1 Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 - 1 | Limit setting status |
Parameter 6: Device type
Device type (Read-only)Value:Curtain motor: 0x01Shutter:0x11Venetian: 0x12 Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 1 | Curtain motor |
| 17 | Shutter |
| 18 | Venetian |
Parameter 7: Power supply type
Power supply type (Read-only)Value:Mains power: 0Battery power: 1 Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Powered by Mains supply |
| 1 | Powered by Battery |
Parameter 8: Open borders
Open bordersValue:Enable open boarders: 1Close open boarders: 0 Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Close open boarders |
| 1 | Enable open boarders |
Parameter 9: Close borders
Close bordersValue:Enable close boarders: 1Close close boarders: 0 Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Close close boarders |
| 1 | Open close boarders |
Technical Data
| Hardware Platform | ZM5304 |
| Device Type | Window Covering - Pos/End Aware |
| Network Operation | Always On Slave |
| Firmware Version | HW: 144 FW: 1.14:01.00 |
| Z-Wave Version | 6.81.04 |
| Certification ID | ZC10-19086732 |
| Z-Wave Product Id | 0x030A.0x0103.0x0090 |
| Window Covering Control Features | |
| Security V2 | S2_UNAUTHENTICATED |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |
Supported Command Classes
- Association Grp Info
- Association V2
- Basic
- Configuration
- Device Reset Locally
- Firmware Update Md V4
- Manufacturer Specific V2
- Multi Channel Association V3
- Powerlevel
- Security
- Security 2
- Supervision
- Switch Binary
- Switch Multilevel V3
- Transport Service V2
- Version V2
- Zwaveplus Info V2
Explanation of Z-Wave specific terms
- Controller — is a Z-Wave device with capabilities to manage the network. Controllers are typically Gateways,Remote Controls or battery operated wall controllers.
- Slave — is a Z-Wave device without capabilities to manage the network. Slaves can be sensors, actuators and even remote controls.
- Primary Controller — is the central organizer of the network. It must be a controller. There can be only one primary controller in a Z-Wave network.
- Inclusion — is the process of adding new Z-Wave devices into a network.
- Exclusion — is the process of removing Z-Wave devices from the network.
- Association — is a control relationship between a controlling device and a controlled device.
- Wakeup Notification — is a special wireless message issued by a Z-Wave device to announces that is able to communicate.
- Node Information Frame — is a special wireless message issued by a Z-Wave device to announce its capabilities and functions.