ABUS
Nexello 3I/3O Hybrid Module
SKU: PLHA10100
Quickstart
This is a
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.What is Z-Wave?
Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.
This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.
If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.
For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.
Product Description
The module is mounted via a bracket, it is tamper protected and has a back-up battery.Three Inputs for the connection of: Analogue sensors with voltage 0~12VDigital sensors with voltage 0~12VPotential-free outputs NC/NOOpen Collector Outputs OCThree Outputs for connecting actuators with a maximum of 24VDCSPDT (Single Pole, Double Throw) relay (toggle switch)functions:Configurable timer that automatically switches off after a preset period of time (default is 500 ms)The output can be set to activate automatically when the input terminals (see configuration setting)
Prepare for Installation / Reset
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.
Inclusion/Exclusion
On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.
Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.
Quick trouble shooting
Here are a few hints for network installation if things dont work as expected.
- Make sure a device is in factory reset state before including. In doubt exclude before include.
- If inclusion still fails, check if both devices use the same frequency.
- Remove all dead devices from associations. Otherwise you will see severe delays.
- Never use sleeping battery devices without a central controller.
- Dont poll FLIRS devices.
- Make sure to have enough mains powered device to benefit from the meshing
Association - one device controls an other device
Z-Wave devices control other Z-Wave devices. The relationship between one device controlling another device is called association. In order to control a different device, the controlling device needs to maintain a list of devices that will receive controlling commands. These lists are called association groups and they are always related to certain events (e.g. button pressed, sensor triggers, ...). In case the event happens all devices stored in the respective association group will receive the same wireless command wireless command, typically a 'Basic Set' Command.
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | The Lifeline Association is automatically established between the Z-Wave controller and the device at inclusion and defines what information is exchanged between the Z-Wave controller and the device. |
| 2 | 5 | When a signal input is triggered, the unit first sends a BASIC Set ON. When the preset timer expires, it sends a BASIC Set OFF. |
| 3 | 5 | When a signal input is triggered, the unit first sends a BASIC Set ON. When the preset timer expires, it sends a BASIC Set OFF. |
| 4 | 5 | When a signal input is triggered, the unit first sends a BASIC Set ON. When the preset timer expires, it sends a BASIC Set OFF. |
Configuration Parameters
Z-Wave products are supposed to work out of the box after inclusion, however certain configuration can adapt the function better to user needs or unlock further enhanced features.
IMPORTANT: Controllers may only allow configuring signed values. In order to set values in the range 128 ... 255 the value sent in the application shall be the desired value minus 256. For example: To set a parameter to 200 it may be needed to set a value of 200 minus 256 = minus 56. In case of a two byte value the same logic applies: Values greater than 32768 may needed to be given as negative values too.
Parameter 1: Signal input 1 - Mode
Several settings of the signal input and its triggering behaviour. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | No Relay is triggered, No Voltage is present, triggers below lowthreshold |
| 2 - 0 | Relay 1 is triggered, No Voltage is present, triggers below lowthreshold |
| 4 - 0 | Relay 2 is triggered, No Voltage is present, triggers below lowthreshold |
| 6 - 0 | Relay 1 and 2 are triggered, No Voltage is present, triggers below lowthreshold |
| 8 - 0 | Relay 3 is triggered, No Voltage is present, triggers below lowthreshold |
| 10 - 0 | Relay 1 and 3 are triggered, No Voltage is present, triggers below lowthreshold |
| 14 - 0 | Relay 1, 2 and 3 are triggered, No Voltage is present, triggers below lowthreshold |
| 64 - 0 | No Relay is triggered, 3,3V is present, triggers below lowthreshold |
| 66 - 0 | Relay 1 is triggered, 3,3V is present, triggers below lowthreshold |
| 68 - 0 | Relay 2 is triggered, 3,3V is present, triggers below lowthreshold |
| 70 - 0 | Relay 1 and 2 are triggered, 3,3V is present, triggers below lowthreshold |
| 72 - 0 | Relay 3 is triggered, 3,3V is present, triggers below lowthreshold |
| 74 - 0 | Relay 1 and 3 are triggered, 3,3V is present, triggers below lowthreshold |
| 78 - 0 | Relay 1, 2 and 3 are triggered, 3,3V is present, triggers below lowthreshold |
| 128 - 0 | No Relay is triggered, No Voltage is present, triggers above highthreshold |
| 130 - 0 | Relay 1 is triggered, No Voltage is present, triggers above highthreshold |
| 132 - 0 | Relay 2 is triggered, No Voltage is present, triggers above highthreshold |
| 134 - 0 | Relay 1 and 2 are triggered, No Voltage is present, triggers above highthreshold |
| 136 - 0 | Relay 3 is triggered, No Voltage is present, triggers above highthreshold |
| 138 - 0 | Relay 1 and 3 are triggered, No Voltage is present, triggers above highthreshold |
| 142 - 0 | Relay 1, 2 and 3 are triggered, No Voltage is present, triggers above highthreshold |
| 192 - 0 | No Relay is triggered, 3,3V is present, triggers above highthreshold |
| 194 - 0 | Relay 1 is triggered, 3,3V is present, triggers above highthreshold |
| 196 - 0 | Relay 2 is triggered, 3,3V is present, triggers above highthreshold |
| 198 - 0 | Relay 1 and 2 are triggered, 3,3V is present, triggers above highthreshold |
| 200 - 0 | Relay 3 is triggered, 3,3V is present, triggers above highthreshold |
| 202 - 0 | Relay 1 and 3 are triggered, 3,3V is present, triggers above highthreshold |
| 206 - 0 | Relay 1, 2 and 3 are triggered, 3,3V is present, triggers above highthreshold |
| 12 - 0 | Relay 2 and 3 are triggered, No Voltage is present, triggers below lowthreshold |
| 76 - 0 | Relay 2 and 3 are triggered, 3,3V is present, triggers below lowthreshold |
| 140 - 0 | Relay 2 and 3 are triggered, No Voltage is present, triggers above highthreshold |
| 204 - 0 | Relay 2 and 3 are triggered, 3,3V is present, triggers above highthreshold |
Parameter 10: Signal input 2 - voltage low-threshold
Setting of the voltage drop below which the signal input is triggered Size: 1 Byte, Default Value: 10
| Setting | Description |
|---|---|
| 0 - 255 | Adjustable from 0 - 255 in 100mV steps (10 = 1000mV = 1.0V) |
Parameter 11: Signal input 3 - Mode
Same as Parameter 1, but applies to Signal Input 3 Size: 1 Byte, Default Value: 64
| Setting | Description |
|---|---|
| 0 | No Relay is triggered, No Voltage is present, triggers below lowthreshold |
| 2 - 0 | Relay 1 is triggered, No Voltage is present, triggers below lowthreshold |
| 4 - 0 | Relay 2 is triggered, No Voltage is present, triggers below lowthreshold |
| 6 - 0 | Relay 1 and 2 are triggered, No Voltage is present, triggers below lowthreshold |
| 8 - 0 | Relay 3 is triggered, No Voltage is present, triggers below lowthreshold |
| 10 - 0 | Relay 1 and 3 are triggered, No Voltage is present, triggers below lowthreshold |
| 12 - 0 | Relay 2 and 3 are triggered, No Voltage is present, triggers below lowthreshold |
| 14 - 0 | Relay 1, 2 and 3 are triggered, No Voltage is present, triggers below lowthreshold |
| 64 - 0 | No Relay is triggered, 3,3V is present, triggers below lowthreshold |
| 66 - 0 | Relay 1 is triggered, 3,3V is present, triggers below lowthreshold |
| 68 - 0 | Relay 2 is triggered, 3,3V is present, triggers below lowthreshold |
| 70 - 0 | Relay 1 and 2 are triggered, 3,3V is present, triggers below lowthreshold |
| 72 - 0 | Relay 3 is triggered, 3,3V is present, triggers below lowthreshold |
| 74 - 0 | Relay 1 and 3 are triggered, 3,3V is present, triggers below lowthreshold |
| 76 - 0 | Relay 2 and 3 are triggered, 3,3V is present, triggers below lowthreshold |
| 78 - 0 | Relay 1, 2 and 3 are triggered, 3,3V is present, triggers below lowthreshold |
| 128 - 0 | No Relay is triggered, No Voltage is present, triggers above highthreshold |
| 130 - 0 | Relay 1 is triggered, No Voltage is present, triggers above highthreshold |
| 132 - 0 | Relay 2 is triggered, No Voltage is present, triggers above highthreshold |
| 134 - 0 | Relay 1 and 2 are triggered, No Voltage is present, triggers above highthreshold |
| 136 - 0 | Relay 3 is triggered, No Voltage is present, triggers above highthreshold |
| 138 - 0 | Relay 1 and 3 are triggered, No Voltage is present, triggers above highthreshold |
| 140 - 0 | Relay 2 and 3 are triggered, No Voltage is present, triggers above highthreshold |
| 142 - 0 | Relay 1, 2 and 3 are triggered, No Voltage is present, triggers above highthreshold |
| 192 - 0 | No Relay is triggered, 3,3V is present, triggers above highthreshold |
| 194 - 0 | Relay 1 is triggered, 3,3V is present, triggers above highthreshold |
| 196 - 0 | Relay 2 is triggered, 3,3V is present, triggers above highthreshold |
| 198 - 0 | Relay 1 and 2 are triggered, 3,3V is present, triggers above highthreshold |
| 200 - 0 | Relay 3 is triggered, 3,3V is present, triggers above highthreshold |
| 202 - 0 | Relay 1 and 3 are triggered, 3,3V is present, triggers above highthreshold |
| 204 - 0 | Relay 2 and 3 are triggered, 3,3V is present, triggers above highthreshold |
| 206 - 0 | Relay 1, 2 and 3 are triggered, 3,3V is present, triggers above highthreshold |
Parameter 12: Relay output 3 - switching time
Setting for the duration of the switching time when the relay output is switched. Size: 1 Byte, Default Value: 5
| Setting | Description |
|---|---|
| 0 | relay output is permanently switched |
| 1 - 255 | Adjustable duration from 1 - 255 in 100ms steps |
Parameter 13: Signal input 3 - switching time at association group 4
Setting for the duration of the switching time at association group 4 when signal input is triggered. Size: 1 Byte, Default Value: 180
| Setting | Description |
|---|---|
| 0 | Switched permanently |
| 1 - 255 | Adjustable duration from 1 - 255 in seconds |
Parameter 14: Signal input 3 - voltage high-threshold
Setting, from which voltage rise the signal input is triggered Size: 1 Byte, Default Value: 25
| Setting | Description |
|---|---|
| 0 - 255 | Adjustable from 0 - 255 in 100mV steps (25 = 2500mV = 2.5V) |
Parameter 15: Signal input 3 - voltage low-threshold
Setting of the voltage drop below which the signal input is triggered Size: 1 Byte, Default Value: 10
| Setting | Description |
|---|---|
| 0 - 255 | Adjustable from 0 - 255 in 100mV steps (10 = 1000mV = 1.0V) |
Parameter 16: Voltage Report (time)
The interval time of the voltage report for signal input 1-3 Size: 1 Byte, Default Value: 30
| Setting | Description |
|---|---|
| 1 - 255 | Adjustable from 1 - 255 in minutes |
Parameter 17: Sabotage Alarm Relay output
Setting whether a relay output must be switched in case of a sabotage alarm. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | No Relays are triggered |
| 2 - 0 | Relay 1 is triggered |
| 4 - 0 | Relay 2 is triggered |
| 6 - 0 | Relay 1 and 2 are triggered |
| 8 - 0 | Relay 3 is triggered |
| 10 - 0 | Relay 1 and 3 are triggered |
| 12 - 0 | Relay 2 and 3 are triggered |
| 14 - 0 | Relay 1, 2 and 3 are triggered |
Parameter 18: Signal input - Activate arm / disarm message
Setting whether a signal input should send an armed and an unarmed message instead of a trigger signal. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | 0 = No signal input sends arm/disarm message |
| 1 | 1 = Signal input 1 sends arm/disarm message |
| 2 | 2 = Signal input 2 sends arm/disarm message |
| 3 | 3 = Signal input 3 sends arm/disarm message |
Parameter 2: Relay output 1 - switching time
Setting for the duration of the switching time when the relay output is switched. Size: 1 Byte, Default Value: 5
| Setting | Description |
|---|---|
| 0 | relay output is permanently switched |
| 1 - 255 | Adjustable duration from 1 - 255 in 100ms steps |
Parameter 3: Signal input 1 - switching time at association group 2
Setting for the duration of the switching time at association group 2 when signal input is triggered. Size: 1 Byte, Default Value: 180
| Setting | Description |
|---|---|
| 0 | Switched permanently |
| 1 - 255 | Adjustable duration from 1 - 255 in seconds |
Parameter 4: Signal input 1 - voltage high-threshold
Setting, from which voltage rise the signal input is triggered Size: 1 Byte, Default Value: 25
| Setting | Description |
|---|---|
| 0 - 255 | Adjustable from 0 - 255 in 100mV steps (25 = 2500mV = 2.5V) |
Parameter 5: Signal input 1 - voltage low-threshold
Setting of the voltage drop below which the signal input is triggered Size: 1 Byte, Default Value: 10
| Setting | Description |
|---|---|
| 0 - 255 | Adjustable from 0 - 255 in 100mV steps (10 = 1000mV = 1.0V) |
Parameter 6: Signal input 2 - Mode
Same as Parameter 1, but applies to Signal Input 2 Size: 1 Byte, Default Value: 64
| Setting | Description |
|---|---|
| 0 | No Relay is triggered, No Voltage is present, triggers below lowthreshold |
| 2 - 0 | Relay 1 is triggered, No Voltage is present, triggers below lowthreshold |
| 4 - 0 | Relay 2 is triggered, No Voltage is present, triggers below lowthreshold |
| 6 - 0 | Relay 1 and 2 are triggered, No Voltage is present, triggers below lowthreshold |
| 8 - 0 | Relay 3 is triggered, No Voltage is present, triggers below lowthreshold |
| 10 - 0 | Relay 1 and 3 are triggered, No Voltage is present, triggers below lowthreshold |
| 12 - 0 | Relay 2 and 3 are triggered, No Voltage is present, triggers below lowthreshold |
| 14 - 0 | Relay 1, 2 and 3 are triggered, No Voltage is present, triggers below lowthreshold |
| 64 - 0 | No Relay is triggered, 3,3V is present, triggers below lowthreshold |
| 66 - 0 | Relay 1 is triggered, 3,3V is present, triggers below lowthreshold |
| 68 - 0 | Relay 2 is triggered, 3,3V is present, triggers below lowthreshold |
| 70 - 0 | Relay 1 and 2 are triggered, 3,3V is present, triggers below lowthreshold |
| 72 - 0 | Relay 3 is triggered, 3,3V is present, triggers below lowthreshold |
| 74 - 0 | Relay 1 and 3 are triggered, 3,3V is present, triggers below lowthreshold |
| 76 - 0 | Relay 2 and 3 are triggered, 3,3V is present, triggers below lowthreshold |
| 78 - 0 | Relay 1, 2 and 3 are triggered, 3,3V is present, triggers below lowthreshold |
| 128 - 0 | No Relay is triggered, No Voltage is present, triggers above highthreshold |
| 130 - 0 | Relay 1 is triggered, No Voltage is present, triggers above highthreshold |
| 132 - 0 | Relay 2 is triggered, No Voltage is present, triggers above highthreshold |
| 134 - 0 | Relay 1 and 2 are triggered, No Voltage is present, triggers above highthreshold |
| 136 - 0 | Relay 3 is triggered, No Voltage is present, triggers above highthreshold |
| 138 - 0 | Relay 1 and 3 are triggered, No Voltage is present, triggers above highthreshold |
| 140 - 0 | Relay 2 and 3 are triggered, No Voltage is present, triggers above highthreshold |
| 142 - 0 | Relay 1, 2 and 3 are triggered, No Voltage is present, triggers above highthreshold |
| 192 - 0 | No Relay is triggered, 3,3V is present, triggers above highthreshold |
| 194 - 0 | Relay 1 is triggered, 3,3V is present, triggers above highthreshold |
| 196 - 0 | Relay 2 is triggered, 3,3V is present, triggers above highthreshold |
| 198 - 0 | Relay 1 and 2 are triggered, 3,3V is present, triggers above highthreshold |
| 200 - 0 | Relay 3 is triggered, 3,3V is present, triggers above highthreshold |
| 202 - 0 | Relay 1 and 3 are triggered, 3,3V is present, triggers above highthreshold |
| 204 - 0 | Relay 2 and 3 are triggered, 3,3V is present, triggers above highthreshold |
| 206 - 0 | Relay 1, 2 and 3 are triggered, 3,3V is present, triggers above highthreshold |
Parameter 7: Relay output 2 - switching time
Setting for the duration of the switching time when the relay output is switched. Size: 1 Byte, Default Value: 5
| Setting | Description |
|---|---|
| 0 | relay output is permanently switched |
| 1 - 255 | Adjustable duration from 1 - 255 in 100ms steps |
Parameter 8: Signal input 2 - switching time at association group 3
Setting for the duration of the switching time at association group 3 when signal input is triggered. Size: 1 Byte, Default Value: 180
| Setting | Description |
|---|---|
| 0 | Switched permanently |
| 1 - 255 | Adjustable duration from 1 - 255 in seconds |
Parameter 9: Signal input 2 - voltage high-threshold
Setting, from which voltage rise the signal input is triggered Size: 1 Byte, Default Value: 25
| Setting | Description |
|---|---|
| 0 - 255 | Adjustable from 0 - 255 in 100mV steps (25 = 2500mV = 2.5V) |
Technical Data
| Hardware Platform | SD3502 |
| Device Type | Notification Sensor |
| Network Operation | Always On Slave |
| Firmware Version | HW: 1 FW: 1.00:00.04 |
| Z-Wave Version | 6.81.06 |
| Certification ID | ZC10-20076949 |
| Z-Wave Product Id | 0x0403.0x0003.0x0007 |
| Security V2 | S2_UNAUTHENTICATED ,S2_AUTHENTICATED |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |
Supported Command Classes
- Association Grp Info
- Association V2
- Basic
- Battery
- Configuration V4
- Device Reset Locally
- Firmware Update Md V4
- Manufacturer Specific V2
- Multi Channel Association V3
- Multi Channel V4
- Notification V8
- Powerlevel
- Security
- Security 2
- Sensor Multilevel V5
- Supervision
- Switch Binary
- Transport Service V2
- Version V3
- Zwaveplus Info V2
Controlled Command Classes
- Basic
Explanation of Z-Wave specific terms
- Controller — is a Z-Wave device with capabilities to manage the network. Controllers are typically Gateways,Remote Controls or battery operated wall controllers.
- Slave — is a Z-Wave device without capabilities to manage the network. Slaves can be sensors, actuators and even remote controls.
- Primary Controller — is the central organizer of the network. It must be a controller. There can be only one primary controller in a Z-Wave network.
- Inclusion — is the process of adding new Z-Wave devices into a network.
- Exclusion — is the process of removing Z-Wave devices from the network.
- Association — is a control relationship between a controlling device and a controlled device.
- Wakeup Notification — is a special wireless message issued by a Z-Wave device to announces that is able to communicate.
- Node Information Frame — is a special wireless message issued by a Z-Wave device to announce its capabilities and functions.