Custos

Wireless Water Detector 700

SKU: WWDZWU

ZWave+ Security V2

Quickstart

This is a secure Alarm Sensor for . Please make sure the internal battery is fully charged.



Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

What is Z-Wave?

Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.

Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.

This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.

If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.

For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.

Product Description

Custos WWD (Wireless Water Detector) Is the smallest Z-Wave compact wireless water detector with 4 sides water detection capabilities plus integrated port for remote water sensor probe as secondary physical/logical detector, innovative design allows it to work on all orientations without worrying accidental flip, incorporated high energy density lithium battery for up to X years of battery operation life span.

Prepare for Installation / Reset

Please read the user manual before installing the product.

In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.

Inclusion/Exclusion

On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.

Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.

Quick trouble shooting

Here are a few hints for network installation if things dont work as expected.

  1. Make sure a device is in factory reset state before including. In doubt exclude before include.
  2. If inclusion still fails, check if both devices use the same frequency.
  3. Remove all dead devices from associations. Otherwise you will see severe delays.
  4. Never use sleeping battery devices without a central controller.
  5. Dont poll FLIRS devices.
  6. Make sure to have enough mains powered device to benefit from the meshing

Association - one device controls an other device

Z-Wave devices control other Z-Wave devices. The relationship between one device controlling another device is called association. In order to control a different device, the controlling device needs to maintain a list of devices that will receive controlling commands. These lists are called association groups and they are always related to certain events (e.g. button pressed, sensor triggers, ...). In case the event happens all devices stored in the respective association group will receive the same wireless command wireless command, typically a 'Basic Set' Command.

Association Groups:

Group Number Maximum Nodes Description
1 5 Lifeline Group- Device Reset Locally Notification- Sensor Binary Report- Indicator Report- Sensor Multilevel ReportTemperature Temperature level change auto report will be sent after wakeup every time based on Configuration Parameter 0x31 Setting.- Battery Report- Heat Alarm Notification Report (0x04)- 0x00 = State idle- 0x02 = Overheatno location support -- 0x06 = Underheatno location support- Water Alarm Notification Report (0x05)- 0x00 = State idle- 0x02 = Water leak detectedno location support- Power Management Notification (0x08)- 0x00 = State Idle- 0x11 = Battery Fluid is low
2 5 - Basic Set- 0x00 = IDEL / CANCEL (Based on Configuration Parameter 0x41 Setting)- 0xFF = TRIGGERED (Based on Configuration Parameter 0x40 Setting)-0x00 = Let the water run through (Based on Configuration Parameter 0x13)-0xFF = Doesnt let the water run through. (Based on Configuration Parameter 0x12)- 0x00 = Let the water run through (Based on Configuration Parameter 0x13)- 0xFF = Doesnt let the water run through. (Based on Configuration Parameter 0x12)
3 5 - Basic Set- 0x00 = IDEL / CANCEL (Based on Configuration Parameter 0x43 Setting)- 0xFF = TRIGGERED (Based on Configuration Parameter 0x42 Setting)-0xFF = TRIGGERED (Based on Configuration Parameter 0x31 Setting)
4 5 - Basic Set- 0x00 = IDEL / CANCEL (Based on Configuration Parameter 0x45 Setting)- 0xFF = TRIGGERED (Based on Configuration Parameter 0x44 Setting)
5 5 - Basic Set- 0x00 = IDEL / CANCEL (Based on Configuration Parameter 0x47 Setting)- 0xFF = TRIGGERED (Based on Configuration Parameter 0x46 Setting)

Configuration Parameters

Z-Wave products are supposed to work out of the box after inclusion, however certain configuration can adapt the function better to user needs or unlock further enhanced features.

IMPORTANT: Controllers may only allow configuring signed values. In order to set values in the range 128 ... 255 the value sent in the application shall be the desired value minus 256. For example: To set a parameter to 200 it may be needed to set a value of 200 minus 256 = minus 56. In case of a two byte value the same logic applies: Values greater than 32768 may needed to be given as negative values too.

Parameter 16: Sensors Function Set

Sensors Function Enable / Disable
Size: 1 Byte, Default Value: 15

Setting Description
0 Built-in Water Detection Probe *(Default Enabled)
1 - 0 Remote Water Detection Probe *(Default Enabled)
2 - 0 Overheat Detection *(Default Enabled)
3 - 0 Freeze Detection *(Default Enabled)

Parameter 17: Water Leak Cancellation Report Set

Water Leak Probe Cancellation Report Set
Size: 1 Byte, Default Value: 1

Setting Description
0 Send Basic SET when Water Alarm Cancelled Either Built-in or Remote Water Detection Probe
1 - 0 Send Basic SET when Water Alarm Cancelled Built-in And Remote Water Detection Probe

Parameter 32: Battery Level Change Auto Report

Battery Level Change Value to auto report
Size: 1 Byte, Default Value: 10

Setting Description
0 Disable Battery Level Change Auto Report
1 - 63 Auto report when wake up every time. *(Default 0x0A = 10%)

Parameter 33: Battery Threshold Level Report

Battery Lower Threshold Level Report
Size: 1 Byte, Default Value: 30

Setting Description
1 - 99 Battery Lower Threshold Valve Report *(Default 30%)

Parameter 48: Temperature Report Unit

Configure Temperature Report Unit
Size: 1 Byte, Default Value: 2

Setting Description
0 Disable Temperature Report
1 - 0 Report Celsius C unit
2 - 0 Report Fahrenheit F unit

Parameter 49: Temperature Level Change Report

Temperature Level Change to auto report
Size: 2 Byte, Default Value: 260

Setting Description
0 - 255 From 0C to 255C
256 - 511 From 0F to 255F

Parameter 50: Temperature Value Offset Report

Temperature Value Offset Report Set
Size: 2 Byte, Default Value: 256

Setting Description
0 - 255 From 0C to 255C
4096 - 4351 From -1C to -255C
256 - 511 From 0F to 255F
4353 - 4607 From -1F to -255F

Parameter 51: Overheat Trigger Value

Overheat Trigger Value SET
Size: 2 Byte, Default Value: 360

Setting Description
0 - 255 From 0C to 255C
256 - 511 From 0F to 255F

Parameter 52: Overheat Cancellation Value

Overheat Cancellation Value auto report
Size: 2 Byte, Default Value: 342

Setting Description
0 - 255 From 0C to 255C
256 - 511 From 0F to 255F

Parameter 53: Freeze Trigger Value

Configure Freeze Trigger Report value
Size: 2 Byte, Default Value: 360

Setting Description
0 - 255 From 0C to 255C
256 - 511 From 0F to 255F

Parameter 54: Freeze Recover Value

Configure Freeze Recover Report Value
Size: 2 Byte, Default Value: 342

Setting Description
0 - 255 From 0C to 255C
256 - 511 From 0F to 255F

Parameter 64: AG2 - Built-in Water Leak Trigger

Built-in Water Leak Trigger Basic SET
Size: 1 Byte, Default Value: 1

Setting Description
0 Disable Basic Set (Send nothing)
1 - 0 Basic Set ON (0xFF)
2 - 0 Basic Set OFF (0x00)

Parameter 65: AG2 - Built-in Water Leak Cancellation

Built-in Water Leak Cancellation Basic SET
Size: 1 Byte, Default Value: 0

Setting Description
0 Disable Basic Set (Send nothing)
1 - 0 Basic Set ON (0xFF)
2 - 0 Basic Set OFF (0x00)

Parameter 66: AG3 - Remote Water Leak Trigger

Remote Water Leak Trigger Basic SET
Size: 1 Byte, Default Value: 1

Setting Description
0 Disable Basic Set (Send nothing)
1 - 0 Basic Set ON (0xFF)
2 - 0 Basic Set OFF (0x00)

Parameter 67: AG3 - Remote Water Leak Cancellation

Remote Water Leak Cancellation Basic SET
Size: 1 Byte, Default Value: 0

Setting Description
0 Disable Basic Set (Send nothing)
1 - 0 Basic Set ON (0xFF)
2 - 0 Basic Set OFF (0x00)

Parameter 68: AG4 - Overheat Trigger Value

Overheat Trigger Value Basic SET
Size: 1 Byte, Default Value: 0

Setting Description
0 Disable Basic Set (Send nothing)
1 - 0 Basic Set ON (0xFF)
2 - 0 Basic Set OFF (0x00)

Parameter 69: AG4 - Overheat Recover Value

Overheat Recover Value Basic SET
Size: 1 Byte, Default Value: 0

Setting Description
0 Disable Basic Set (Send nothing)
1 - 0 Basic Set ON (0xFF)
2 - 0 Basic Set OFF (0x00)

Parameter 70: AG5 - Freeze Trigger Value

Freeze Trigger Value Basic SET
Size: 1 Byte, Default Value: 0

Setting Description
0 Disable Basic Set (Send nothing)
1 - 0 Basic Set ON (0xFF)
2 - 0 Basic Set OFF (0x00)

Parameter 71: AG5 - Freeze Recover Value

Freeze Recover Value Basic SET
Size: 1 Byte, Default Value: 0

Setting Description
0 Disable Basic Set (Send nothing)
1 - 0 Basic Set ON (0xFF)
2 - 0 Basic Set OFF (0x00)

Parameter 80: Resend Water Leak Notification Time

Resend Water Leak Notification Time Set
Size: 1 Byte, Default Value: 0

Setting Description
0 Do not resend
1 - 30 1 - 30 Minutes

Parameter 96: Buzzer Related Function Actions

Buzzer Related Function Actions Set
Size: 1 Byte, Default Value: 3

Setting Description
0 Buzzer Enable responds with GSensor in action *(Default 1 = Eanbled)
1 - 0 Buzzer Enable responds with Water Leak Detection *(Default 1 = Enabled)

Parameter 97: Buzzer Sound Saving Mode

Sound works first 3S Water Leak Detected
Size: 1 Byte, Default Value: 1

Setting Description
0 Disable Saving mode (Buzzer sound works during whole Water Leak is detected)
1 - 0 Enable Saving mode (Buzzer function only works 3s when Water Leak is detected)

Technical Data

Hardware Platform ZGM130
Device Type Notification Sensor
Network Operation Reporting Sleeping Slave
Firmware Version HW: 1 FW: 2.00
Z-Wave Version 7.14.3
Certification ID ZC12-21010160
Z-Wave Product Id 0x0270.0x0201.0x010B
Outdoor Use ok
Security V2 S2_UNAUTHENTICATED ,S2_AUTHENTICATED
Frequency XXfrequency
Maximum transmission power XXantenna

Supported Command Classes

  • Application Status
  • Association Grp Info V3
  • Association V3
  • Battery
  • Configuration V4
  • Device Reset Locally
  • Firmware Update Md V5
  • Indicator V3
  • Manufacturer Specific V2
  • Multi Channel Association V4
  • Notification V8
  • Powerlevel
  • Security 2
  • Sensor Binary V2
  • Sensor Multilevel V11
  • Supervision
  • Transport Service V2
  • Version V3
  • Wake Up V2
  • Zwaveplus Info V2
    •

Explanation of Z-Wave specific terms

  • Controller — is a Z-Wave device with capabilities to manage the network. Controllers are typically Gateways,Remote Controls or battery operated wall controllers.
  • Slave — is a Z-Wave device without capabilities to manage the network. Slaves can be sensors, actuators and even remote controls.
  • Primary Controller — is the central organizer of the network. It must be a controller. There can be only one primary controller in a Z-Wave network.
  • Inclusion — is the process of adding new Z-Wave devices into a network.
  • Exclusion — is the process of removing Z-Wave devices from the network.
  • Association — is a control relationship between a controlling device and a controlled device.
  • Wakeup Notification — is a special wireless message issued by a Z-Wave device to announces that is able to communicate.
  • Node Information Frame — is a special wireless message issued by a Z-Wave device to announce its capabilities and functions.