Zooz
Dimmer Switch 800
SKU: ZEN72 800LR
Quickstart
This is a
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.What is Z-Wave?
Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.
This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.
If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.
For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.
Product Description
Use the 800LR Zooz smart dimmer in smart lighting applications for smooth lighting control and reliable wireless communication.
Prepare for Installation / Reset
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.
Safety Warning for Mains Powered Devices
ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.
Inclusion/Exclusion
On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.
Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.
Quick trouble shooting
Here are a few hints for network installation if things dont work as expected.
- Make sure a device is in factory reset state before including. In doubt exclude before include.
- If inclusion still fails, check if both devices use the same frequency.
- Remove all dead devices from associations. Otherwise you will see severe delays.
- Never use sleeping battery devices without a central controller.
- Dont poll FLIRS devices.
- Make sure to have enough mains powered device to benefit from the meshing
Association - one device controls an other device
Z-Wave devices control other Z-Wave devices. The relationship between one device controlling another device is called association. In order to control a different device, the controlling device needs to maintain a list of devices that will receive controlling commands. These lists are called association groups and they are always related to certain events (e.g. button pressed, sensor triggers, ...). In case the event happens all devices stored in the respective association group will receive the same wireless command wireless command, typically a 'Basic Set' Command.
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | |
| 2 | 5 | |
| 3 | 5 | |
| 4 | 5 |
Configuration Parameters
Z-Wave products are supposed to work out of the box after inclusion, however certain configuration can adapt the function better to user needs or unlock further enhanced features.
IMPORTANT: Controllers may only allow configuring signed values. In order to set values in the range 128 ... 255 the value sent in the application shall be the desired value minus 256. For example: To set a parameter to 200 it may be needed to set a value of 200 minus 256 = minus 56. In case of a two byte value the same logic applies: Values greater than 32768 may needed to be given as negative values too.
Parameter 1: Locally Button function
Change the function of the up and down key. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 10: Multilevel minimum value
Set the maximum brightness value. Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 11: Multilevel maximum value
Set the minimum brightness value. Size: 1 Byte, Default Value: 99
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 12: Double Tap Behavior
Double Tap behavior. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 13: Enable or Disable Scene
Enable or disable the center scene. Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 15: Enable or Disable local/Z-Wave control
Disable the output. Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 16: Rate for manually dimming
Ramp rate for local press & hold. Size: 1 Byte, Default Value: 5
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 18: Custom brightness level
Custom brightness level. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 19: 3-way switch type
External switch type. Size: 1 Byte, Default Value: 2
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 2: LED Indicator
Indicator behavior. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 20: Association reports
Select the final or each level report type. Size: 1 Byte, Default Value: 2
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 21: Disabled Relay Behavior
Enable or disable report. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 22: Night Mode Brightness Level
Set the brightness of night light. Size: 1 Byte, Default Value: 20
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 23: LED Indicator Color
Setting indicator led's color. Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 24: LED Indicator Brightness
Setting indicator led's brightness. Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 25: Single Tap Behavior
Single tap behavior. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 26: Disable programming from button
Enable or Disable the local button function. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 27: Ramp rate for physical off
Rate when turn off by short press the paddle. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 28: Ramp rate for hub on
Rate when turn on by HUB. Size: 1 Byte, Default Value: 255
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 29: Ramp rate for hub off
Rate when turn off by HUB. Size: 1 Byte, Default Value: 255
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 3: Auto Turn-Off Timer
Setting auto off minutes. Size: 4 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 30: Ramp rate for multilevel start
Rate for association group 4. Size: 1 Byte, Default Value: 5
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 31: Scene of momentary switch in 3-way
Enable scene from momentary switch in 3-way. Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 32: Disable LED blinking
Disable LED blinking when a setting is changed. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 5: Auto Turn-On Timer
Setting auto on minutes. Size: 4 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 7: Association Group Trigger
Select control association group way. Size: 1 Byte, Default Value: 15
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 8: Restores state
Restore state after power failure. Size: 1 Byte, Default Value: 2
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 9: Ramp rate for physical on
Rate for manually turn on. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | 0 |
Technical Data
| Hardware Platform | EFR32ZG23A |
| Device Type | Multilevel Switch DT |
| Network Operation | Always On End Node |
| Firmware Version | HW: 03 FW: 03.10 |
| Z-Wave Version | 7.19.2 |
| Certification ID | ZC14-23080308 |
| Z-Wave Product Id | 0x027A.0x7000.0xA002 |
| Color | White |
| Z-Wave Scene Type | Central Scene |
| Neutral Wire Required | ok |
| Firmware Updatable | Updatable by Consumer by RF |
| Electric Load Type | Dimmable LEDIncandescent |
| Security V2 | S2_UNAUTHENTICATED ,S2_AUTHENTICATED |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |
Supported Command Classes
- Association Grp Info V3
- Association V2
- Basic V2
- Central Scene V3
- Configuration V4
- Device Reset Locally
- Firmware Update Md V5
- Indicator V3
- Manufacturer Specific V2
- Multi Channel Association V3
- Switch Multilevel V4
- Powerlevel
- Security 2
- Supervision
- Transport Service V2
- Version V3
- Zwaveplus Info V2
Explanation of Z-Wave specific terms
- Controller — is a Z-Wave device with capabilities to manage the network. Controllers are typically Gateways,Remote Controls or battery operated wall controllers.
- Slave — is a Z-Wave device without capabilities to manage the network. Slaves can be sensors, actuators and even remote controls.
- Primary Controller — is the central organizer of the network. It must be a controller. There can be only one primary controller in a Z-Wave network.
- Inclusion — is the process of adding new Z-Wave devices into a network.
- Exclusion — is the process of removing Z-Wave devices from the network.
- Association — is a control relationship between a controlling device and a controlled device.
- Wakeup Notification — is a special wireless message issued by a Z-Wave device to announces that is able to communicate.
- Node Information Frame — is a special wireless message issued by a Z-Wave device to announce its capabilities and functions.