Zooz
Zooz Z-Wave Long Range Titan Water Valve Actuator
SKU: ZAC36LR
Quickstart
This is a
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.What is Z-Wave?
Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.
This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.
If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.
For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.
Product Description
Use the Z-Wave shut-off valve actuator to shut your main water valve automatically when a leak is detected.
Prepare for Installation / Reset
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.
Inclusion/Exclusion
On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.
Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.
Quick trouble shooting
Here are a few hints for network installation if things dont work as expected.
- Make sure a device is in factory reset state before including. In doubt exclude before include.
- If inclusion still fails, check if both devices use the same frequency.
- Remove all dead devices from associations. Otherwise you will see severe delays.
- Never use sleeping battery devices without a central controller.
- Dont poll FLIRS devices.
- Make sure to have enough mains powered device to benefit from the meshing
Association - one device controls an other device
Z-Wave devices control other Z-Wave devices. The relationship between one device controlling another device is called association. In order to control a different device, the controlling device needs to maintain a list of devices that will receive controlling commands. These lists are called association groups and they are always related to certain events (e.g. button pressed, sensor triggers, ...). In case the event happens all devices stored in the respective association group will receive the same wireless command wireless command, typically a 'Basic Set' Command.
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | |
| 2 | 5 | |
| 3 | 5 | |
| 4 | 5 | |
| 5 | 5 |
Configuration Parameters
Z-Wave products are supposed to work out of the box after inclusion, however certain configuration can adapt the function better to user needs or unlock further enhanced features.
IMPORTANT: Controllers may only allow configuring signed values. In order to set values in the range 128 ... 255 the value sent in the application shall be the desired value minus 256. For example: To set a parameter to 200 it may be needed to set a value of 200 minus 256 = minus 56. In case of a two byte value the same logic applies: Values greater than 32768 may needed to be given as negative values too.
Parameter 100: Motor Full Close Offset
Motor Full Close Offset (%) Size: 1 Byte, Default Value: 4
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 113: Battery Threshold Change
Battery Threshold To Auto Report Size: 1 Byte, Default Value: 10
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 114: Low Battery Report Level
Low Battery Level to Report Size: 1 Byte, Default Value: 30
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 115: Low Battery Detection Valve Control
Water Valve Low Battery Control Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 17: Inverse Water Valve Report
Inverse Switch Binary Report value Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 18: Association Group 2 SET Value
Valve SET Value when receives 0xFF Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 19: Association Group 2 SET Value
Valve SET Value when receives 0x00 Size: 1 Byte, Default Value: 2
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 33: Temperature Report Unit
Configure reporting temperature unit Size: 1 Byte, Default Value: 2
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 34: Temperature Threshold Change
Temperature Threshold to auto report Size: 2 Byte, Default Value: 260
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 35: Temperature Sensor Offset
Configure Temperature Report Offset Size: 2 Byte, Default Value: 256
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 36: Overheat Trigger Value
Configure Overheat Trigger Report Value Size: 2 Byte, Default Value: 360
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 37: Overheat Recover Value
Configure overheat recover report value Size: 2 Byte, Default Value: 342
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 38: Association Group 4 Overheat Trigger
Overheat trigger SET value Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 39: Association Group 4 Overheat Cancel
Overheat cancellation SET value Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 40: Freeze Trigger Value
Configure Freeze Trigger Report Value Size: 2 Byte, Default Value: 288
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 41: Freeze Recover Value
Configure Freeze Recover Report Value Size: 2 Byte, Default Value: 292
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 42: Freeze Detection Valve Control
Configure Valve Control during freeze Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 43: Association Group 5 Freeze Trigger
Configure freeze trigger SET value Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 44: Association Group 5 Freeze Cancel
Freeze cancellation SET value Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 45: Temperature Auto Report Time Interval Set
Auto Report Time in Mins Size: 1 Byte, Default Value: 15
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 49: Association Group 3 Water Leak Trigger
Water Leak Trigger SET value Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 50: Association Group 3 Water Leak Cancel
Water Leak Cancellation SET value Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 51: Water Leak Detection Valve Control
Enable / Disable Water Leak Valve Control Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 52: Water Leak Cancellation Time
Report When No Longer Trigger Size: 1 Byte, Default Value: 10
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 65: Buzzer
Disable/Enable Buzzer Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 66: LED Brightness Level
Configure LED brightness level Size: 1 Byte, Default Value: 80
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 67: Touch Keylock Protection
Disable / Enable Touch Keylock Protection Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 81: Notification - Water Valve
Disable / Enable Water Valve Report Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 82: Notification - Overheat
Disable / Enable Overheat Report Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 83: Notification - Freeze
Disable / Enable Freeze Report Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 84: Notification - Water Leak
Disable / Enable Water Leak Report Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 85: Notification - AC Power
Disable / Enable AC Power Report Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 86: Notification - Battery
Disable / Enable Battery Report Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 97: Motor Auto Control
Motor Auto Control Size: 1 Byte, Default Value: 3
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 98: Motor Auto Control Day
Motor Auto Control Day Size: 1 Byte, Default Value: 14
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 99: Motor Full Open Offset
Motor Full Open Offset (%) Size: 1 Byte, Default Value: 9
| Setting | Description |
|---|---|
| 0 | 0 |
Technical Data
| Hardware Platform | ZGM130S037HGN2 / ZGM130S037HGN1 |
| Device Type | Binary Switch DT |
| Network Operation | Always On End Node |
| Firmware Version | HW: 04 FW: 02.00 |
| Z-Wave Version | 7.18.8 |
| Certification ID | ZC14-24070455 |
| Z-Wave Product Id | 0x027A.0x0101.0x0036 |
| Outdoor Use | ok |
| Color | |
| Firmware Updatable | |
| IP (Ingress Protection) Rated | ok |
| Security V2 | S2_UNAUTHENTICATED ,S2_AUTHENTICATED |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |
Supported Command Classes
- Application Status
- Association Grp Info V3
- Association V2
- Basic V2
- Battery V2
- Switch Binary V2
- Configuration V4
- Device Reset Locally
- Firmware Update Md V5
- Indicator V3
- Manufacturer Specific V2
- Multi Channel Association V3
- Sensor Multilevel V11
- Notification V8
- Powerlevel
- Security 2
- Supervision
- Transport Service V2
- Version V3
- Zwaveplus Info V2
Explanation of Z-Wave specific terms
- Controller — is a Z-Wave device with capabilities to manage the network. Controllers are typically Gateways,Remote Controls or battery operated wall controllers.
- Slave — is a Z-Wave device without capabilities to manage the network. Slaves can be sensors, actuators and even remote controls.
- Primary Controller — is the central organizer of the network. It must be a controller. There can be only one primary controller in a Z-Wave network.
- Inclusion — is the process of adding new Z-Wave devices into a network.
- Exclusion — is the process of removing Z-Wave devices from the network.
- Association — is a control relationship between a controlling device and a controlled device.
- Wakeup Notification — is a special wireless message issued by a Z-Wave device to announces that is able to communicate.
- Node Information Frame — is a special wireless message issued by a Z-Wave device to announce its capabilities and functions.