FIBARO

Refurbished - FIBARO Roller Shutter 4

SKU: B_FIBEFGR-224

Quickstart

This is a Z-Wave Device for . To run this device please connect it to your mains power supply.

Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

What is Z-Wave?

Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.

Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.

This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.

If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.

For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.

Product Description

Reliable design, advanced technology and even better - the new FIBARO Roller Shutter 4!

The FIBARO Roller Shutter 4 - equipped with the Z-Wave 800 chip - is a device designed to control roller shutters, awnings, blinds, curtains and pergolas. The roller shutter enables precise positioning of roller shutters or blind slits. The device is equipped with energy monitoring. It enables the control of connected devices either via the Z-Wave network or a directly connected switch.

FIBARO focussed on easy installation and an intuitive initial design. There are more inputs for N and L cables, so there is no need to use connection terminals. The shape and dimensions of the device allow easy and quick installation in flush-mounted boxes. The button and diode are easily accessible. Equipped with plug-in connectors, it enables even faster installation - no screwdriver required. Three extra connection cables for connecting the switch are included. The integrated bridge provides a simple bridging option for phase and neutral. It is not necessary to use Wago connectors to connect wires. You save space in the box and reduce installation time thanks to the push-in wire connection.

Features:

Flush-mounted wireless module for integrating existing installations such as roller blinds, venetian blinds, pergolas, curtains, awnings, blind motors with electronic or mechanical limit switches into the Z-Wave network
Equipped with Z-Wave 800 chip to provide better range
Supports Z-Wave network Security Modes: S0 with AES-128 encryption and S2 Authenticated with PRNG-based encryption
Active power and energy metering functionality
Works as a Z-Wave signal repeater (all non-battery operated devices within the network will act as repeaters to increase reliability of the network
Works with various types of switches – momentary, toggle and dedicated roller blind switches
Easy and quick too install thanks to push-in wires connector and inbuilt bridge
To be installed in wall switch boxes
Power Supply: 100-240V~50/60Hz
Rated Load Current: 2A for motors with compensated power factor (inductive loads)
Supported Motor Type: single-phase AC motors
Required Limit Switches: electronic or mechanic
Operating Temperature: 0°C - 35°C
For Installation in Boxes: Ø = 50mm, depth ? 60mm
Wireless Protocol: Z-Wave (800 series chip)
Wireless Signal Power: up to 5dBm
Wireless Frequency band: 868.4 MHz
Range: Up to 100m outdoors, up to 30m indoors (depending on the terrain and building structure)

We would like to point out that this article is not a new product. The product has got the complete functionality, but may have the following characteristics:

broken seal,
damaged packaging,
no original packaging
missing accessories,
minimal signs of wear,
no current software version.

We offer to you a guarantee of one year. With a possible return you receive a credit note, there is no exchange of the product. The picture may not correspond to the scope of delivery of the product. If you are interested in a larger quantity of used products, please contact your sales representative.

Prepare for Installation / Reset

Please read the user manual before installing the product.

In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.

Safety Warning for Mains Powered Devices

ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.

Inclusion/Exclusion

On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.

Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.

Quick trouble shooting

Here are a few hints for network installation if things dont work as expected.

Make sure a device is in factory reset state before including. In doubt exclude before include.
If inclusion still fails, check if both devices use the same frequency.
Remove all dead devices from associations. Otherwise you will see severe delays.
Never use sleeping battery devices without a central controller.
Dont poll FLIRS devices.
Make sure to have enough mains powered device to benefit from the meshing

Technical Data

Dimensions	0.0950000x0.0950000x0.0250000 mm
Weight	114 gr
Frequency	XXfrequency
Maximum transmission power	XXantenna

Explanation of Z-Wave specific terms

Controller — is a Z-Wave device with capabilities to manage the network. Controllers are typically Gateways,Remote Controls or battery operated wall controllers.
Slave — is a Z-Wave device without capabilities to manage the network. Slaves can be sensors, actuators and even remote controls.
Primary Controller — is the central organizer of the network. It must be a controller. There can be only one primary controller in a Z-Wave network.
Inclusion — is the process of adding new Z-Wave devices into a network.
Exclusion — is the process of removing Z-Wave devices from the network.
Association — is a control relationship between a controlling device and a controlled device.
Wakeup Notification — is a special wireless message issued by a Z-Wave device to announces that is able to communicate.
Node Information Frame — is a special wireless message issued by a Z-Wave device to announce its capabilities and functions.