Aqara
Aqara Camera Hub G3 EU (Zigbee)
SKU: AQAZCH-H03
Quickstart
This is a
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.What is Z-Wave?
Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.
This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.
If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.
For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.
Product Description
The Aqara Camera Hub G3 impresses with its all-round compatibility. The device supports HomeKit Secure Video, Amazon Alexa and Google Home, ensuring connected compatible devices support Home Kit, Alexa, Google Assistant and more.
Local Al-powered recognition.
Thanks to a powerful processor with NPU, the Camera Hub G3 is able to recognise faces, gestures and pets locally, which can be used for notifications and home automation.
2K 1296p resolution.
The Camera Hub G3 features a high-resolution 2304 x 1296 pixel sensor for crystal clear image quality full of detail
Type-C connector with video output.
The Camera Hub G3 uses the most advanced and universal connector that supports high definition, low latency video output via the UVC protocol.
Built-in Zigbee 3.0 hub.
The Camera Hub G3 is not just a camera, but also an embedded smart home hub. It can connect and control up to 128 compatible devices.
Local infrared control.
The G3 has a built-in IR controller that can make your existing infrared compatible devices smart and support local automations. In addition, all IR automations are local and run even when there is no internet connection
360° viewing angle.
The 110° wide-angle lens combined with the pan and tilt motors provides a rotation angle of up to 360°, supports automatic travel and face and pet tracking.
Dual-band 2.4/5 GHz WLAN.
Worry no more about network type compatibility: the Camera Hub G3 supports the two most popular Wi-Fi frequencies and uses them to connect your Aqara devices to the network.
Features:
- Radio Protocol: Zigbee 3.0 IEEE 802.15.4, Wi-Fi IEEE 802.11 b/g/n/a/ac 2.4/5 GHz.
- Local memory: microSD card (not included). CLASS 4 or higher supported, up to 128 GB memory.
- Operating temperature: -10°C - 40°C
- Humidity: 0 - 95% RH non-condensing
- Connections: USB C
- Power supply: 5V 2 A
- Power consumption: 10W
- Video resolution: 2k 2304x1296p
- Viewing angle: 110
- Pan/Tilt angle: Horizontal 340°, Vertical 45° (up 30°, down 15°)
- Local Storage: Micro SD-Card CLASS 4 128GB
Prepare for Installation / Reset
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.
Safety Warning for Mains Powered Devices
ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.
Inclusion/Exclusion
On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.
Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.
Quick trouble shooting
Here are a few hints for network installation if things dont work as expected.
- Make sure a device is in factory reset state before including. In doubt exclude before include.
- If inclusion still fails, check if both devices use the same frequency.
- Remove all dead devices from associations. Otherwise you will see severe delays.
- Never use sleeping battery devices without a central controller.
- Dont poll FLIRS devices.
- Make sure to have enough mains powered device to benefit from the meshing
Technical Data
| Dimensions | 0.0851000x0.1234000x0.0861000 mm |
| Weight | 510 gr |
| EAN | 6970504214873 |
| Certification ID | ZIG21237ZB331097-24 |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |
Explanation of Z-Wave specific terms
- Controller — is a Z-Wave device with capabilities to manage the network. Controllers are typically Gateways,Remote Controls or battery operated wall controllers.
- Slave — is a Z-Wave device without capabilities to manage the network. Slaves can be sensors, actuators and even remote controls.
- Primary Controller — is the central organizer of the network. It must be a controller. There can be only one primary controller in a Z-Wave network.
- Inclusion — is the process of adding new Z-Wave devices into a network.
- Exclusion — is the process of removing Z-Wave devices from the network.
- Association — is a control relationship between a controlling device and a controlled device.
- Wakeup Notification — is a special wireless message issued by a Z-Wave device to announces that is able to communicate.
- Node Information Frame — is a special wireless message issued by a Z-Wave device to announce its capabilities and functions.