Aqara
Aqara Motion Sensor P1 (Zigbee)
SKU: AQAZMS-S02
Quickstart
This is a
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.What is Z-Wave?
Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.
This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.
If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.
For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.
Product Description
The Aqara Motion Sensor P1 detects body motion and the state of ambient light. If there are any people moving or any change in the ambient light state in the areas under detection, the motion sensor will send notice to the Aqara Home app through the connected Aqara Zigbee 3.0 Hub or link to other devices.
Configurable Detection Timeout.
Finally, the detection timeout can be configured without any hardware modding. Just set any timeout from 1 to 200 seconds, confirm by pressing the device button, and the P1 won"t be stuck for one minute, like before. (Please note: decreasing the detection timeout leads to shorter battery life)
Up to 5-Year Battery Life*.
Thanks to the energy saving technologies and improved batteries, the Motion Sensor P1 now can reach a record up to five-year battery life, which will make its battery life long even in case of extra-low temperatures or lightning-fast detection timeouts. *Up to 5-year battery life can be achieved with the LED indication function turned off and with detection timeout not less than 30 seconds.
All-Round Compatibility.
Compatible with the most popular smart home ecosystems. HomeKit, Alexa, IFTTT, and more are supported. Matter support will be available as an OTA update of Aqara hubs after the official release of specification.
170° Field of View.
Extra wide field of view, 170° for up to 2 meters and 150° for up to 7 meters. Moreover, thanks to its versatile 360-degree stand, the viewing angle can be adjusted so that only the motion in the desired area (e.g., bed or sink) will be detected.
Adjustable Sensitivity (Distance).
The user can configure how sensitive the sensor will be. Three sensitivity modes (high, medium and low), refer to the distance the sensor will be triggered from, which can help to reduce false alarms and make installation more flexible.
Built-in Light Sensor.
The light sensor built-in into the P1 can be used to control the lights more precisely. For example, only turn on the lights when it"s dark and motion is detected in order to save energy and increase the lifespan of lights.
Smart Home Automations.
Motion sensor is a natural part of the majority of smart home automations: configure the IF conditions as well as THEN actions, and many routine tasks such as turning on the lights, opening curtains or controlling the TV will become automated. Aqara Zigbee 3.0 hub and controllers are required for this functionality.
Local and Remote Alarm.
Thanks to the Aqara Home Alert System, the Motion Sensor P1 may become a reliable security device: configure away mode in the app, and enjoy constant monitoring, local sound and light alarms and cloud notifications in case motion is detected. Or, use it in HomeKit or other supported systems for the same purpose.
Zigbee 3.0 Protocol.
Enjoy the benefits of the fastest, most stable, and energy-efficient smart home technology. Better stability and compatibility (more standardized protocol), longer support, and more features.
Future-Proofing via OTA.
The sensor now supports OTA updates, which means that new features and fixes can be added after the release of the product.
Features:
- Zigbee enabled Motion Sensor
- Model: MS-S02
- Color: White
- Dimensions: 33.1 × 33.1 × 41.6mm
- Battery: 2 × CR2450
- Product Packaging Size: 55 × 37 × 70mm
- Product Weight: 33g
- Detection Angle: ?170°
- Detection Distance: ?7m
- Battery Capacity: 1240mAh
- Wireless Connections: Zigbee 3.0
- Wireless Frequency: 2.4GHz (2400?2483.5MHz)
- Operating Temperature: -10??+55?
- Operating Humidity: 0 ~ 95%RH, no condensation
- What"s in the box: Motion Sensor P1, Holder?Sticker?User Manual
Prepare for Installation / Reset
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.
Safety Warning for Mains Powered Devices
ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.
Inclusion/Exclusion
On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.
Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.
Quick trouble shooting
Here are a few hints for network installation if things dont work as expected.
- Make sure a device is in factory reset state before including. In doubt exclude before include.
- If inclusion still fails, check if both devices use the same frequency.
- Remove all dead devices from associations. Otherwise you will see severe delays.
- Never use sleeping battery devices without a central controller.
- Dont poll FLIRS devices.
- Make sure to have enough mains powered device to benefit from the meshing
Technical Data
| Dimensions | 0.0330000x0.0330000x0.0420000 mm |
| Weight | 33 gr |
| EAN | 6970504215979 |
| Certification ID | ZIG22047ZB331282-24 |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |
Explanation of Z-Wave specific terms
- Controller — is a Z-Wave device with capabilities to manage the network. Controllers are typically Gateways,Remote Controls or battery operated wall controllers.
- Slave — is a Z-Wave device without capabilities to manage the network. Slaves can be sensors, actuators and even remote controls.
- Primary Controller — is the central organizer of the network. It must be a controller. There can be only one primary controller in a Z-Wave network.
- Inclusion — is the process of adding new Z-Wave devices into a network.
- Exclusion — is the process of removing Z-Wave devices from the network.
- Association — is a control relationship between a controlling device and a controlled device.
- Wakeup Notification — is a special wireless message issued by a Z-Wave device to announces that is able to communicate.
- Node Information Frame — is a special wireless message issued by a Z-Wave device to announce its capabilities and functions.