Aqara
Aqara Hub M1S Gen2 EU (Zigbee, Wi-Fi)
SKU: AQAZHM1S-G02
Quickstart
This is a
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.What is Z-Wave?
Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.
This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.
If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.
For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.
Product Description
Aqara Hub M1S Gen 2 is a smart home control centre that connects Zigbee devices to Wi-Fi networks. At the same time, it can manage and control smart scenes and can conveniently control smart devices such as plugs, switches, light bulbs, curtains and so on.
Zigbee 3.0 support, up to 128 devices.
Supports all current Aqara devices, based on the fastest, most stable and energy-efficient technology. Up to 128 Aqara Zigbee devices can be connected to the hub (repeater devices such as Smart Plug and Wall Switch (with Neutral) are required).
Built-in speaker.
A powerful 2-watt speaker can be used as an alarm or doorbell as well as via configurable automations.
RGB light and illumination sensor.
The M1S Gen 2 is not only a Zigbee 3.0 smart home hub, but also has built-in RGB lighting with 18 powerful LEDs and a diffuser. It can be used as an alarm, accent or night light and has configurable brightness and colour. Compared to our previous hubs, it also has a fully functional lighting sensor that can be used in automations via the Aqara Home app.
All-round compatibility.
Use your favourite voice assistant or smart home ecosystem together with the automations of the Aqara Home app. Apple Siri, Amazon Alexa, Google Assistant and more are supported.
Improved Wi-Fi connectivity.
The M1S Gen 2 has a more powerful 2x2 MIMO Wi-Fi antenna and supports the WPA3 standard, making the connection faster, more secure and more reliable.
Focus on security.
In addition to the Aqara alarm system, the M1S Gen 2 supports all 4 HomeKit alarm modes
High-quality components and design.
High-quality components and design are not only a discreet addition to any room décor, but also make the M1S Gen 2 more reliable as a constant airflow is achieved through the large perforated base.
Configurable ringtones.
M1S Gen 2 now supports custom MP3 ringtones that can be uploaded for voice prompts and used in automations. For example, the hub will say "Good night" when the corresponding scene is triggered.
Features:
- Input voltage: 100-240V~, 50/60Hz
- Input current: 0.2A
- Power: 7W (Max)
- Wireless protocols: Zigbee 3.0 IEEE 802.15.4
- Operating temperature: -10°~ 40°C
- Storage temperature: -10°~ 40°C
- Operating humidity: ?95% RH
Prepare for Installation / Reset
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.
Safety Warning for Mains Powered Devices
ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.
Inclusion/Exclusion
On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.
Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.
Quick trouble shooting
Here are a few hints for network installation if things dont work as expected.
- Make sure a device is in factory reset state before including. In doubt exclude before include.
- If inclusion still fails, check if both devices use the same frequency.
- Remove all dead devices from associations. Otherwise you will see severe delays.
- Never use sleeping battery devices without a central controller.
- Dont poll FLIRS devices.
- Make sure to have enough mains powered device to benefit from the meshing
Technical Data
| Dimensions | 0.0800000x0.0800000x0.0410000 mm |
| Weight | 138 gr |
| EAN | 6970504217416 |
| Certification ID | ZIG22052ZB331287-24 |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |
Explanation of Z-Wave specific terms
- Controller — is a Z-Wave device with capabilities to manage the network. Controllers are typically Gateways,Remote Controls or battery operated wall controllers.
- Slave — is a Z-Wave device without capabilities to manage the network. Slaves can be sensors, actuators and even remote controls.
- Primary Controller — is the central organizer of the network. It must be a controller. There can be only one primary controller in a Z-Wave network.
- Inclusion — is the process of adding new Z-Wave devices into a network.
- Exclusion — is the process of removing Z-Wave devices from the network.
- Association — is a control relationship between a controlling device and a controlled device.
- Wakeup Notification — is a special wireless message issued by a Z-Wave device to announces that is able to communicate.
- Node Information Frame — is a special wireless message issued by a Z-Wave device to announce its capabilities and functions.