Shelly (Allterco Robotics LTD)
Shelly 1 Mini G3
SKU: ALRLMINI1G3
Quickstart
This is a
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.What is Z-Wave?
Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.
This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.
If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.
For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.
Product Description
The smallest relay switch in the world for smart control. Automate your lights, garage door, irrigation system, or other small electrical appliances in less than 10 minutes and control them from anywhere. Small enough to fit behind any wall switch or socket, Shelly 1 Mini Gen3 can be retrofitted and is highly compatible with your existing smart ecosystem.
Designed with convenience in mind, these mini relays have all the capabilities of standard switches fit into a compact and space-saving form factor. Despite their small size, the Shelly Mini Gen3 devices don"t compromise on performance or functionality. Equipped with our powerful Shelly chip featuring 8MB of memory, device efficiency and responsiveness are significantly improved, guaranteeing smoother and faster operation.
Wi-Fi Operated.
Connect Shelly 1 Mini Gen3 to your Wi-Fi network. No HUB required!
Bluetooth.
Quick inclusion via Bluetooth or use it as a Bluetooth gateway.
Dry Contacts.
Use it to control a wide range of devices and appliances.
Matter.
Each Gen3 device is engineered to be upgradable to Matter. The doubled memory, compared to Plus series, guarantees a smooth update process, paving the way for new smart capabilities and integrations.
Use Cases:
Lighting Control Wherever You Need It?.
Thanks to its compact size, Shelly Mini 1 Gen3 can discreetly fit within the ceiling rose of your lamp or in jammed wall boxes. Once installed, Shelly Mini 1 Gen3 enables you to effortlessly control your lights or other appliances using the Smart Control App, your preferred platform, or voice assistant. Easily customize your lights according to your daily routine with personalized schedules and save on energy. Set your hallway lights to automatically switch off past your family"s bedtime, ensuring a peaceful night"s sleep. And don"t worry - you can still use your light switches manually to suit the needs of everyone in your home.
Make any small electrical appliance smart?.
Transforming old electrical appliances into smart devices becomes even more accessible with Shelly 1 Mini Gen3. Its 8A limit is perfect for transforming small to medium-sized appliances into smart devices, such as lamps, coffee makers, and others. Place it in the socket or fit it discreetly inside the appliance"s casing, avoiding the need for additional external wiring.
Control your garage door.
Shelly 1 Mini Gen3"s compact design allows for flexible placement options, enabling you to install it directly within the garage door opener"s housing or even near the motor. Its 8A power handling capability ensures reliable garage door control, allowing you to conveniently operate your garage door remotely without the need for bulky external modules.
Features:
- Relay: Dry, NO contact, 1-pole, µ contact
- Power consumption: < 1.2 W
- Max switching voltage AC: 240 V
- Max switching voltage DC:30 V
- Max switching current AC: 8A
- Max switching current DC: 5A
- Max switching power AC: 2000 W
- Max switching power DC:150 W
- Power measurement: No
- Voltage protection / Cutoff:No
- Current protection / Cutoff: No
- Max power protection / Cutoff:No
- Max. RF power < 20 dBm
- Wi-Fi protocol:802.11 b/g/n
- Wi-Fi Range: Up to 30 m indoors and 50 m outdoors
- Ambient temperature: -20 °C to 40 °C
- Humidity30 % to 70 % RH
Prepare for Installation / Reset
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.
Safety Warning for Mains Powered Devices
ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.
Inclusion/Exclusion
On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.
Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.
Quick trouble shooting
Here are a few hints for network installation if things dont work as expected.
- Make sure a device is in factory reset state before including. In doubt exclude before include.
- If inclusion still fails, check if both devices use the same frequency.
- Remove all dead devices from associations. Otherwise you will see severe delays.
- Never use sleeping battery devices without a central controller.
- Dont poll FLIRS devices.
- Make sure to have enough mains powered device to benefit from the meshing
Technical Data
| Dimensions | 0.0330000x0.0250000x0.0160000 mm |
| Weight | 19 gr |
| EAN | 3800235261576 |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |
Explanation of Z-Wave specific terms
- Controller — is a Z-Wave device with capabilities to manage the network. Controllers are typically Gateways,Remote Controls or battery operated wall controllers.
- Slave — is a Z-Wave device without capabilities to manage the network. Slaves can be sensors, actuators and even remote controls.
- Primary Controller — is the central organizer of the network. It must be a controller. There can be only one primary controller in a Z-Wave network.
- Inclusion — is the process of adding new Z-Wave devices into a network.
- Exclusion — is the process of removing Z-Wave devices from the network.
- Association — is a control relationship between a controlling device and a controlled device.
- Wakeup Notification — is a special wireless message issued by a Z-Wave device to announces that is able to communicate.
- Node Information Frame — is a special wireless message issued by a Z-Wave device to announce its capabilities and functions.