Shelly (Allterco Robotics LTD)
Shelly Plus 1PM
SKU: ALRLSHELL1PMPLUS
Quickstart
This is a
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.What is Z-Wave?
Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.
This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.
If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.
For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.
Product Description
Next generation appliances control with precise power metering.
From automatization of the lights to electrical appliances control, Shelly Plus 1PM provides precise power metering and free cloud data storage. Small enough to fit behind every wall switch or wall socket, the relay is retrofit and can be installed in less than 10 minutes.
Track your power consumption and save money.
You can now monitor and analyze the power consumption of your electrical appliances and save money on electricity bills. Shelly Plus 1PM has an integrated precise power meter that allow you to measure the power consumption and features free data storage for analysis. It can also detect power overconsumption via a pre-set limit reach, then notify you or switch off the device.
Automate any electrical appliance and control it remotely.
With Shelly Plus 1PM you can automate any electrical appliance in your home and control it remotely. Shelly Plus 1PM can control appliances with large load which makes it perfect for kitchen appliances and domestic systems monitoring and control. You can get precise measurement of the power consumption of each appliance and switch in on/off remotely, no matter where you are.
Highly compatible.
Use your preferred voice assistant to control Shelly Plus 1PM. The relay is compatible with most popular voice assistants. For example Amazon Alexa.
No hub required.
Shelly Plus 1PM can be controlled directly and without a hub through your smartphone with Shelly Cloud App. Manage and control your home or facility, set scenes, schedules, and adjust settings wherever you are through the Cloud access, or only on the local network!
Features:
- Power supply: 110-240V ±10% 50/60Hz AC, 24-240V DC
- Max load per channel: 16A
- Working temperature: 0°C ÷ 40°C
- Wireless/Wi-Fi: Protocol 802.11 b/g/n (2.4 GHz)
- Electrical consumption: < 1,2 W
- Control through REST, CoAP, and MQTT
- Power metering with data storage: Provides precise monitoring of the power consumption.
- Bluetooth: Add devices quickly and easily via Bluetooth connection, using Shelly Cloud App.
- Extremely fast processor: For immediate command execution and notification
- Enhanced safety: Over-temperature protection with software thresholds for prevention of failures.
- Improved API interface: Broad range of cloud connections and local integrations.
- No hub required: Control directly without a hub through your smartphone with Shelly Cloud App
- Highly compatible: Use with your preferred home automation platforms and voice assistants.
- Works with Aeotec SmartThings and Homey
- Compatible with Amazon Alexa and Google Home Assistant
Download high resolution images for Shelly products.
Prepare for Installation / Reset
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.
Safety Warning for Mains Powered Devices
ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.
Inclusion/Exclusion
On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.
Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.
Quick trouble shooting
Here are a few hints for network installation if things dont work as expected.
- Make sure a device is in factory reset state before including. In doubt exclude before include.
- If inclusion still fails, check if both devices use the same frequency.
- Remove all dead devices from associations. Otherwise you will see severe delays.
- Never use sleeping battery devices without a central controller.
- Dont poll FLIRS devices.
- Make sure to have enough mains powered device to benefit from the meshing
Technical Data
| Dimensions | 0.0410000x0.0360000x0.0170000 mm |
| Weight | 28 gr |
| EAN | 3800235265017 |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |
Explanation of Z-Wave specific terms
- Controller — is a Z-Wave device with capabilities to manage the network. Controllers are typically Gateways,Remote Controls or battery operated wall controllers.
- Slave — is a Z-Wave device without capabilities to manage the network. Slaves can be sensors, actuators and even remote controls.
- Primary Controller — is the central organizer of the network. It must be a controller. There can be only one primary controller in a Z-Wave network.
- Inclusion — is the process of adding new Z-Wave devices into a network.
- Exclusion — is the process of removing Z-Wave devices from the network.
- Association — is a control relationship between a controlling device and a controlled device.
- Wakeup Notification — is a special wireless message issued by a Z-Wave device to announces that is able to communicate.
- Node Information Frame — is a special wireless message issued by a Z-Wave device to announce its capabilities and functions.