Heatit
Heatit Wi-Fi Panel Heater 400W - 1500W
SKU: HEAL5430469
Quickstart
This is a
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.What is Z-Wave?
Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.
This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.
If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.
For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.
Product Description
The Heatit WiFi Panel Heater is a modern, smart electric panel heater designed for efficient and comfortable heating of living and working spaces. With its slim, timeless design, the heater blends discreetly into any room and is ideal for residential areas, offices, holiday homes, or smart home environments. Control is flexible via the integrated control panel, Bluetooth, or conveniently via Wi?Fi using the MyHeatit app. Thanks to an open API, the panel heater can also be integrated into existing smart home systems.
The integrated digital thermostat ensures precise temperature control between 5 and 40?°C, while two heating modes – Comfort and Eco – provide an optimal balance between warmth and energy efficiency. Features such as active energy consumption monitoring, open?window detection, a child lock, as well as overheat and tip?over protection enhance comfort, transparency, and safety in everyday use. The Heatit WiFi Panel Heater is designed for wall mounting and is supplied with a suitable wall bracket. Optionally, the unit can be used as a freestanding heater with separately available feet.
Highlights
- Smart control via Wi?Fi (2.4?GHz) and Bluetooth
- Control via MyHeatit app, local control panel, or open API
- Suitable for integration into smart home systems
- Digital thermostat with precise temperature control from 5 to 40?°C
- Two heating modes: Comfort and Eco
- Adjustable heating output depending on the model from 100?W to 1500?W
- Silent power regulation using triac technology
- Active energy consumption monitoring with real?time display
- Open?window detection to reduce unnecessary energy consumption
- Child lock for safe operation
- Overheat and tip?over protection
- Splash?proof according to IP24
- Over?the?Air (OTA) firmware updates
- Modern, slim design in matt white or black
- Wall mounting possible, optional freestanding feet available
Technical Data
- Rated power: 400?W - 1500 W
- Supply voltage: 230?V AC
- Recommended room size: approx. 20 to 24?m²
- Operating temperature range: 5 to 40?°C
- Storage temperature range: ?30 to 70?°C
- Wireless technology: 2.4 GHz Wi-Fi, Bluetooth
- Protection class: IP24
- Material: steel
- Mounting type: wall mounting with bracket, freestanding with optional feet
- Cable length: approx. 1.3?m
- Depth incl. wall bracket: approx. 80?mm
- Manufacturer’s warranty: 2 years
Prepare for Installation / Reset
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.
Safety Warning for Mains Powered Devices
ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.
Inclusion/Exclusion
On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.
Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.
Quick trouble shooting
Here are a few hints for network installation if things dont work as expected.
- Make sure a device is in factory reset state before including. In doubt exclude before include.
- If inclusion still fails, check if both devices use the same frequency.
- Remove all dead devices from associations. Otherwise you will see severe delays.
- Never use sleeping battery devices without a central controller.
- Dont poll FLIRS devices.
- Make sure to have enough mains powered device to benefit from the meshing
Technical Data
| EAN | 7071236019572 |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |
Explanation of Z-Wave specific terms
- Controller — is a Z-Wave device with capabilities to manage the network. Controllers are typically Gateways,Remote Controls or battery operated wall controllers.
- Slave — is a Z-Wave device without capabilities to manage the network. Slaves can be sensors, actuators and even remote controls.
- Primary Controller — is the central organizer of the network. It must be a controller. There can be only one primary controller in a Z-Wave network.
- Inclusion — is the process of adding new Z-Wave devices into a network.
- Exclusion — is the process of removing Z-Wave devices from the network.
- Association — is a control relationship between a controlling device and a controlled device.
- Wakeup Notification — is a special wireless message issued by a Z-Wave device to announces that is able to communicate.
- Node Information Frame — is a special wireless message issued by a Z-Wave device to announce its capabilities and functions.