MCO Home
Shutter Panel Switch UK
SKU: MCOEC321
Quickstart
This is a
1. Power the panel on, if LEDs flick 4 times, it shows the device is not in any Z-Wave network. If LEDs turns to orange directly, the panel is in a network already.
2. Set controller into Include/Exclude mode, and press 8 seconds or 3 clicks on "UP" or "DOWN" button to add/remove. If succeed, green LED flicks 4 times.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
Shutter Panel Switch is a wall panel built-in with Z-Wave Plus module. With its stylish design and stable performance, the panel can be used to wire roller shutter which controlled by AC motor (with limit). It supports basic command class，multi channel command class and multi channel association command class, also works as a repeater in a Z-Wave network. This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from any other manufacturers.
Installation
Step 1: Remove the steel frame from the device, and secure it onto the junction box with two screws.
Step 2: Insert all wires into the right terminals by following the wiring diagrams as below, and tighten screws.
Step 3: Attach the wired device on “A” points of the steel frame as shown first, and then push the whole device into junction box.
Step 4: Confirm the device is well mounted, power on and it is ready to operate.
Product Usage
Manual Operation：
1. When powered on, touch "UP/DOWN" button and release, the shutter starts to move up or down.
2. When shutter moves up, press UP button again can stop the moving.
3. When shutter moves down, press DOWN button again can stop the moving.
Calibration (on the panel)：
Important:
- Make sure the shutter is not reaching its bottom limit before calibration.
- During calibration, any touches on buttons will quit the calibration without success.
Press 4 times on "UP" button, its green LED flicks; and then press 4 times on "DOWN" button, green LED flicks, to show the calibration starting automatically.
1. A demo trip which help to read motor data will start as follow:
-- Shutter starts moving down.
-- After a while the shutter stops, all LEDs turn off.
-- Wait for 2 sec without any button touch; two green LEDs flick 4 times, the demo trip finished.
2. Then shutter moves up until upper limit.
3. Shutter moves down until bottom limit.
4. Then shutter moves up again until upper limit.
At this time, two green LEDs flick 4 times to show calibration succeed.
Calibration (on a controller)：
Refer to parameter table for more details:
Write Parameter 07 with 1: activate demo trip only.
Write Parameter 09 with 1: activate demo trip and calibration together.
Write Parameter 10 with 1: activate calibration only.
Shutter open/close level setting:
Note: To set the levels, please operate the calibration first.
1. The min level of shutter close (down movement):
Manual：Make sure the shutter is not at its bottom limit. Press 6 times of the Down button, the shutter starts moving down. Then press the Down button once to stop the movement where you want. The shutter will stop here when close from now on.
Parameter：Item 11; Range 0-98
2. The max level of shutter open (up movement):
Manual：Make sure the shutter is not at its upper limit. Press 6 times of the Up button, the shutter starts moving up. Then press the Up button once to stop the movement where you want. The shutter will stop here when open from now on.
Parameter：Item 12; Range 1-99
Energy Consumption Monitoring:
When requested by controller, the panel will report voltage, current and power consumption (the command class which support this function is Meter Command Class).
| Reset to factory default | Press 10 times of UP or DOWN button or exclude the device from Z-Wave network, then cut off the main power. The factory setting will be restored. |
| Inclusion | 1. Power the panel on, if LEDs flick 4 times, it shows the device is not in any Z-Wave network. If LEDs turns to orange directly, the panel is in a network already.
2. Set controller into Include/Exclude mode, and press 8 seconds or 3 clicks on "UP" or "DOWN" button to add/remove. If succeed, green LED flicks 4 times. |
| Exclusion | 1. Power the panel on, if LEDs flick 4 times, it shows the device is not in any Z-Wave network. If LEDs turns to orange directly, the panel is in a network already.
2. Set controller into Include/Exclude mode, and press 8 seconds or 3 clicks on "UP" or "DOWN" button to add/remove. If succeed, green LED flicks 4 times. |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 1 | Lifeline |
Configuration Parameters
Parameter 1: Watt Meter Report period
Size: 2 Byte, Default Value: 720
| Setting | Description |
|---|---|
| 1 - 32767 | Unit 5sec 5*720S=3600S= 1hour |
Parameter 2: KWH Meter Report period
Size: 2 Byte, Default Value: 6
| Setting | Description |
|---|---|
| 1 - 32767 | Unit 10min 6*10min=1 hour |
Parameter 5: Level Report Mode
Size: 1 Byte, Default Value: 2
| Setting | Description |
|---|---|
| 1 | Report destination level in 5s period when requested by the gateway; And then report current level after 5s. |
| 2 | Report every 10% level change while running |
Parameter 7: Demo trip
Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 1 | activate demo trip only |
Parameter 8: LED Backlit brightness level
Size: 1 Byte, Default Value: 10
| Setting | Description |
|---|---|
| 0 | LED disabled |
| 1 - 10 | Min level-Max level |
| 11 - 255 | same level as 10 |
Parameter 9: Demo trip and calibration
Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 1 | activate demo trip and calibration |
Parameter 10: Auto calibration
Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 1 | activate calibration |
Parameter 11: Min level of the shutter close
Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 98 | in % |
Parameter 1: Max level of the shutter open
Size: 1 Byte, Default Value: 99
| Setting | Description |
|---|---|
| 1 - 99 | in % |
Parameter 255: Factory setting
Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 85 | Factory Reset |
Technical Data
| Dimensions | 0.0860000x0.0860000x0.0420000 mm |
| Weight | 163 gr |
| Hardware Platform | ZM5202 |
| EAN | 6928954214004 |
| IP Class | IP 20 |
| Voltage | 230 V |
| Load | 2x 3,5 A |
| Device Type | Window Covering Position/Endpoint Aware |
| Generic Device Class | Multilevel Switch |
| Specific Device Class | Motor Control Device (C) |
| Firmware Version | 03.02 |
| Z-Wave Version | 04.3e |
| Z-Wave Product Id | 0x015f.0xc321.0x5102 |
| Frequency | Europe - 868,4 Mhz |
| Maximum transmission power | 5 mW |