MCO Home

Touch Panel Dimmer UK

SKU: MCOEDT311

ZWave+

Quickstart

This is a Routing Multilevel Switch for XXXQFrequencyName. To run this device please connect it to your mains power supply. To add this device to your network execute the following action:

1. Set controller into Add mode and press 3 clicks on "+" or "-" button to add. If succeed, green LED flicks 4 times.
2. If an external switch panel wired, press/toggle the button on that panel 3 times also can add the network (To make the external panel work, set the parameter 14 with value 1, 2, 3 or 4).



Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

Product Description

Dimmer Switch is a wall panel built-in with Z-Wave Plus module. With its stylish design and stable performance, the panel can be used to control the light level. It supports basic command class，multi channel command class and multi channel association command class, also works as a repeater in a Z-Wave network. This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from any other manufacturers.

Installation



Step 1: Remove the steel frame from the device, and secure it onto the junction box with two screws.
Step 2: Insert all wires into the right terminals by following the wiring diagrams as below, and tighten screws.
Step 3: Attach the wired device on “A” points of the steel frame as shown first, and then push the whole device into junction box.
Step 4: Confirm the device is well mounted, power on and it is ready to operate.

Note: S1, S2, Sx are optional terminals for an external dimmer panel input.

Product Usage

Dimming Mode Setting:
The panel can be manually configured or automatically detect different light source by following the steps as below:

1. Touch “+” 4 times and its green LED flashes, then touch “-” 4 times and 2 green LED flashes for 3 sec. The panel enters Dimming mode setting. 

2. During setting, the “+” LED color will inform the current dimming mode:
Leading edge for inductive loads
Trailing edge for capacitive or resistive loads
On/off only
Automatically detection
Orange LED flashing
Green LED flashing
Orange and Green LEDs flashing together
Orange and Green LEDs flashing alternately

3. Touch “-” will switch among the four modes:

Leading edge -> Trailing edge -> On/off only -> Auto detection -> Leading E...

4. Touch “+” to confirm the mode you chose, the mode’s LED color will flash 3 sec to finish the setting. If Auto detection chosen, pls wait the panel to detect the light source and confirm leading
edge or trailing edge dimming itself.

Manual Operation：
1. When powered on, hold "+/-" button will dimming the light level up or down.(Not valid when the dimming mode is “on/off only”)
2. Double click of “+” will turn on the light to the brightness level, and double click of “-” will turn off the light.

Energy Consumption Monitoring:
When requested by controller, the panel will report voltage, current and power consumption (the command class which support this function is Meter Command Class).
The dimming percentage when single touch of button “+” or “-”

1. Parameter 0x0B is used to set the value.
For instance: The current light level is 0, and the set value is 16. When first single touch “+”, the light level will reach 16, and the second single touch of “+” will make the level reach 32, single touch “- ” will make it back to 16 again.
2. Hold the “+” or “-” and release, the changed light level percentage during the holding will be saved and performed in the next single touch dimming.

Notification:
1. Parameter 32 and 33 are used to set the notification threshold.
2. When enabled, will send unsolicited notification frame to gateway.
Reset to factory default
Press 10 times of any button or exclude the device from Z-Wave network, then cut off the main power. The factory setting will be restored.
Inclusion
1. Set controller into Add mode and press 3 clicks on "+" or "-" button to add. If succeed, green LED flicks 4 times.
2. If an external switch panel wired, press/toggle the button on that panel 3 times also can add the network (To make the external panel work, set the parameter 14 with value 1, 2, 3 or 4).
Exclusion
1. Set controller into Remove mode, and press 3 clicks on "+" or "-" button to remove. If succeed, green LED flicks 4 times.
2. If an external switch panel wired, press/toggle the button on that panel 3 times also can remove the network (To make the external panel work, set the parameter 14 with value 1, 2, 3 or 4).
NIF XXXNIF
Wakeup XXXWakeupDescription
Protection XXXProtection
FirmwareUpdate XXXFirmwareUpdate
SetAssociation XXXSetAssociation

Association Groups:

Group Number Maximum Nodes Description
1 1 Lifeline - Send unsolicited reports to the gateway
2 5 Send Switch_Multilevel CC to associated devices
5 5 Associate with Key “+” Send Basic Set CC to associated devices
8 5 Associate with Key “-” Send Basic Set CC to associated devices

Configuration Parameters

Parameter 1: Dimmer state saved or not when power down


Size: 1 Byte, Default Value: 0

Setting Description
0 not saved，Dimmer will be off when powered again
1 saved，Dimmer will keep the same state when powered again

Parameter 2: Dimming mode


Size: 1 Byte, Default Value: 1

Setting Description
0 leading edge
1 trailing edge
2 On/off only

Parameter 3: Auto detection of dimming mode when powered on


Size: 1 Byte, Default Value: 0

Setting Description
0 Auto detection disabled
1 Auto detection enabled

Parameter 4: LED Backlit brightness level


Size: 1 Byte, Default Value: 10

Setting Description
0 LED disabled
1 - 10 Min level - Max level

Parameter 5: Minimum brightness level

The max level should always higher than min level
Size: 1 Byte, Default Value: 1

Setting Description
1 - 98 percentage brightness level

Parameter 6: Maximum brightness level

The max level should always higher than min level
Size: 1 Byte, Default Value: 99

Setting Description
2 - 99 percentage brightness level

Parameter 7: Single dimming step time(Manual)

Manual control realized by holding external button
Size: 2 Byte, Default Value: 3

Setting Description
1 - 2550 Max 2.55s, in 10ms steps

Parameter 8: Single dimming step size(Manual)

Manual control realized by holding external button
Size: 1 Byte, Default Value: 1

Setting Description
1 - 99 percentage value (modification isn’t recommended)

Parameter 9: Single dimming step time (Auto)

Auto control realized by: - one click; - double click of external button; - send Z-Wave CC
Size: 2 Byte, Default Value: 3

Setting Description
1 - 2550 Max 2.55s, in 10ms steps

Parameter 10: Single dimming step size (Auto)

Auto control realized by: - one click; - double click of external button; - send Z-Wave CC
Size: 1 Byte, Default Value: 1

Setting Description
1 - 99 percentage value (modification isn’t recommended)

Parameter 11: The dimming percentage when single touch of button “+” or “-”

With this parameter you can set the light level the lamp will reach when you turn on the lamp of single touch “+”
Size: 1 Byte, Default Value: 0

Setting Description
0 the percentage get by the last button-holding touch
1 - 99 percentage value

Parameter 12: Reporting interval for dimming level


Size: 1 Byte, Default Value: 10

Setting Description
0 No report during dimming
1 - 255 send report in1-255*10ms interval

Parameter 13: External switch type


Size: 1 Byte, Default Value: 0

Setting Description
0 Button (Momentary buttons )
1 Toggle (2-state Switches )

Parameter 14: External switch input


Size: 2 Byte, Default Value: 0

Setting Description
0 function disabled
1 wire 1 ex.switch key to S1 only
2 wire 1 ex.switch key to S2 only
3 wire 2 ex.switch keys to S1 and S2,each key can control both dimming directions
4 wire 2 ex.switch keys to S1 and S2, each key control one dimming direction

Parameter 15: Energy meter reporting


Size: 1 Byte, Default Value: 0

Setting Description
1 Watt
2 KWH
4 Ampere
8 Voltage
15 All

Parameter 16: Energy meter reporting interval


Size: Byte, Default Value: 16

Setting Description
1 - 255 n*1sec

Parameter 17: Beep


Size: 1 Byte, Default Value: 1

Setting Description
0 beep disabled
1 beep enabled

Parameter 32: Ampere alarm threshold


Size: 2 Byte, Default Value: 0

Setting Description
0 alarm disabled
1 - 5000 1-5000*0.01 A alarm enabled

Parameter 33: Voltage alarm threshold


Size: 2 Byte, Default Value: 0

Setting Description
0 alarm disabled
1 - 10000 1-10000*0.1 V alarm enabled

Parameter 255: Factory setting


Size: 1 Byte, Default Value: 0

Setting Description
85 FF Factory setting

Technical Data

Dimensions 0.0860000x0.0860000x0.0420000 mm
Weight 156 gr
Hardware Platform ZM5202
EAN 6928954212000
IP Class IP 20
Voltage 230 V
Load 20 - 200W
Device Type Dimmer
Generic Device Class Multilevel Switch
Specific Device Class Routing Multilevel Switch
Firmware Version 02.06
Z-Wave Version 04.3e
Z-Wave Product Id 0x015f.0xd311.0x5102
Frequency Europe - 868,4 Mhz
Maximum transmission power 5 mW
EuropeDimmer