myStrom

myStrom WiFi Button Plus

SKU: MYSLPQWBP2


Quickstart

This is a Z-Wave Device for . To run this device please connect it to your mains power supply.



Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

What is Z-Wave?

Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.

Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.

This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.

If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.

For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.

Product Description

myStrom WiFi Button Plus - The clever Button that reunites four buttons to control light, music, blinds and everything else, including sensors for temperature and – for the first time – air humidity. The smart little button that controls devices even without an app. 4 buttons, up to 3 functions per button. Designed in Switzerland.

Make your Smart Home even simpler.
WiFi Buttons are easy to place anywhere and make your Smart Home accessible to everyone in your household – in a simple and understated way.

A clear Plus – added comfort.
The four buttons with functions that can be triggered with “press”, “double press” and “long press” makes the WiFi Button Plus the perfect remote control for lights, SONOS and SYMFONISK speakers via myStrom app and electric blinds with dingz or Shelly actuators, for example.

Another clear Plus – practical environmental sensors.
A WiFi Button Plus measures temperature and humidity – this sets the premise for many a useful automation: make sure you have the best climate conditions in your wine cellar, optimise your heating performance and let myStrom control your devices through clever Actions, for example with a myStrom WiFi Switch and a Humidity Action.

Control devices from other manufacturers.
With myStrom Home a WiFi Button Plus can also control your Philips Hue, IKEA TRÅDFRI and Shelly devices.

Limitless possibilities thanks to IFTTT.
With the IFTTT App (free for myStrom customers) a myStrom Button can control almost everything that is Internet-based, e.g. send notifications, reserve a room via calendar, coordinated, order a coffee or even go to the next slide of your presentation - and much more. IFTTT Automation for humidity and temperature values available from 2023.

Also for your existing Smart Homes.
With some Know-How (or the right Plugin) you can integrate a WiFi Button Plus into your existing Smart Home Solution. We are compatible with many systems and offer a well-documented REST API.

Features:

Prepare for Installation / Reset

Please read the user manual before installing the product.

In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.

Safety Warning for Mains Powered Devices

ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.

Inclusion/Exclusion

On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.

Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.

Quick trouble shooting

Here are a few hints for network installation if things dont work as expected.

  1. Make sure a device is in factory reset state before including. In doubt exclude before include.
  2. If inclusion still fails, check if both devices use the same frequency.
  3. Remove all dead devices from associations. Otherwise you will see severe delays.
  4. Never use sleeping battery devices without a central controller.
  5. Dont poll FLIRS devices.
  6. Make sure to have enough mains powered device to benefit from the meshing

Technical Data

Dimensions 0.0540000x0.0540000x0.0120000 mm
Weight 44 gr
EAN 7629999165007
Frequency XXfrequency
Maximum transmission power XXantenna

Explanation of Z-Wave specific terms