myStrom

myStrom WiFi Motion Sensor

SKU: MYSLWMS1


Quickstart

This is a Z-Wave Device for . To run this device please connect it to your mains power supply.



Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

What is Z-Wave?

Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.

Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.

This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.

If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.

For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.

Product Description

myStrom WiFi Motion Sensor - The smart motion detector that automatically switches lights and devices when you move and saves electricity when you’re away.

More efficiency for your Apple Home.
Switch your devices with your presence or your absence. It’s comfortable and automatically saves energy. The temperature and luminosity data measured by the device are visible in your Apple Home App and can be used for automation. Learn more about myStrom + Apple HomeKit®

A home that reacts.
With the Motion Sensor, lights and devices automatically adapt to your behaviour: when you are home, when you are away, or when the lighting situation changes.

And … action!
With the powerful Actions, any WiFi Motion Sensor event – motion, brightness, temperature – can become the trigger for a scene or notification.

Saving energy? Being away is enough.
The motion sensor automatically switches off lights and devices when absent. This helps you save electricity in the most convenient way – and you don’t need to do anything.

Automatically sets the scene.
Thanks to myStrom scenes, the motion sensor also controls several devices at the same time – and can even adjust the brightness and light colour of bulbs.

Different scenes for different times of day.
The brightness sensor makes the Motion Sensor even more suitable for everyday use. Depending on the lighting, it can automatically switch alternating scenes: For example, it prevents the devices from switching on during the day, or let it turn on a cozy lighting scene at night.

Knowing the room temperature.
As a bonus, the integrated temperature sensor makes the Motion Sensor even more useful. Thanks to it, you can easily ensure optimum temperature conditions and be notified when the temperature reaches, exceeds or falls below a certain level.

Plug in, done.
The Motion Sensor is tiny, robust and works for any power outlet. It generates no battery waste and requires no installation material.

Features:

Prepare for Installation / Reset

Please read the user manual before installing the product.

In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.

Safety Warning for Mains Powered Devices

ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.

Inclusion/Exclusion

On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.

Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.

Quick trouble shooting

Here are a few hints for network installation if things dont work as expected.

  1. Make sure a device is in factory reset state before including. In doubt exclude before include.
  2. If inclusion still fails, check if both devices use the same frequency.
  3. Remove all dead devices from associations. Otherwise you will see severe delays.
  4. Never use sleeping battery devices without a central controller.
  5. Dont poll FLIRS devices.
  6. Make sure to have enough mains powered device to benefit from the meshing

Technical Data

Dimensions 0.0400000x0.0750000x0.0250000 mm
Weight 35 gr
EAN 7629999058644
Frequency XXfrequency
Maximum transmission power XXantenna

Explanation of Z-Wave specific terms