Nuki

Nuki Smart Lock Pro (4. Generation) Black

SKU: NU-SL4G-PRO_B


Quickstart

This is a Z-Wave Device for . To run this device please connect it to your mains power supply.



Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

What is Z-Wave?

Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.

Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.

This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.

If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.

For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.

Product Description

Nuki Smart Lock Pro (4th Generation) – The Smartest Door Lock Ever

With an improved battery life and Matter technology, the Nuki Smart Lock Pro offers seamless integration into your smart home.

With the free Nuki app, your smartphone becomes the key. Open your front door in seconds with a simple swipe or let the Auto Unlock function open it automatically for you. Benefit from practical features and smart automations that make your daily life easier.

Say goodbye to insecure key hiding spots. Grant up to 200 individual access permissions to those who matter most. A glance at the log lets you know who came and went, and when. The built-in Wi-Fi module also allows you to control your Nuki Smart Lock remotely. You can always be sure your door is locked – for peace of mind.

Thanks to the universal communication standard Matter, connecting your smart home devices is easier than ever – regardless of brand or model. The optimized power pack offers up to six months of battery life with just one charge.

Installation is a breeze: In just a few minutes, your Nuki Smart Lock will be set up – no screws or drilling required. And if needed, it can be removed without leaving any residue. Moving house? Simply take your Smart Lock with you.

Enhance your Nuki Smart Lock with our wide range of accessories and find the perfect solution that fits your life. Check now if Nuki is compatible with your door: nuki.io/check

Highlights:

Technical Data:

Prepare for Installation / Reset

Please read the user manual before installing the product.

In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.

Safety Warning for Mains Powered Devices

ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.

Inclusion/Exclusion

On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.

Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.

Quick trouble shooting

Here are a few hints for network installation if things dont work as expected.

  1. Make sure a device is in factory reset state before including. In doubt exclude before include.
  2. If inclusion still fails, check if both devices use the same frequency.
  3. Remove all dead devices from associations. Otherwise you will see severe delays.
  4. Never use sleeping battery devices without a central controller.
  5. Dont poll FLIRS devices.
  6. Make sure to have enough mains powered device to benefit from the meshing

Technical Data

Dimensions 0.0600000x0.1300000x0.0650000 mm
Weight 223 gr
EAN 9120072083358
Frequency XXfrequency
Maximum transmission power XXantenna

Explanation of Z-Wave specific terms