Sensative
Sensative Strips Guard 800
SKU: SENEGUARD800
Quickstart
This is a
2. Scan the QR Code (You can find the QR Code on the back of Strips or in the package).
3. Remove both magnets from Strips.* SmartStart will automatically begin 30 seconds after removing the magnets and Strips will be added within 10 minutes when it has been activated within the Z-Wave Controller range.
4. One long LED blink means Strips has been successfully added to your Z-Wave network.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
Strips Guard is an ultra-thin contact sensor and the thinnest magnet sensor in the world, detecting if your doors or windows are open or closed and featuring a design so sleek it disappears right into the architecture of any installation scenario. Strips Guard sends an alarm signal if it detects the opening of any door or window and due to its slim and discrete design, can also be placed in cabinets, on drawers or even behind artwork as an activity sensor. Its unique design allows it to be easily placed almost anywhere, generally in most places where other sensors simply can‘t fit.Strips Guard is an extremely reliable contact sensor. The unique design makes it easy to place nearly invisibly in your home to alert occupants of any open/close or activity event when connected to your Z-Wave smart home system. Strips 800 Series Guard can be used both indoors and out, and the integrated custom battery gives Strips an expected lifetime of 10+ years. For you, this means no hassles with changing or charging batteries in your Strips sensors for the lifetime of the product!Z-Wave Plus 800 series sensors bring a wealth of additional valued features such as longer range, low power consumption for extended battery life and SmartStart technology for instant enrolling. With SmartStart, device inclusion can be initiated automatically by simply removing the included magnets. The Z-Wave gateway then performs the inclusion process in the background without the need for user interaction. 800 Series provides a direct range of 100 meters, an improvement of 60 meters over the 500 series and also includes the industrys best S2 security, providing Strips Guard with the ultimate combination of features to securely protect your home.
Installation
For good communication
Strips use low-power radio signals to communicate with your Z-Wave controller. For best results, please consider the following:
- Strips are designed to fit invisibly in most wood and plastic windows and doors.
- Strips should not be mounted directly on magnetic surfaces or encased within a metal structure as the range will be reduced.
- Strips range is up to 325 feet.
- Any non-battery Z-Wave device will act as a repeater to increase network reliability and range.
For good functionality in the door or window
- To place Strips invisibly, you need a gap in your door or window frame with a minimum height of 3.5 mm.
- Strips may be mounted on the frame (recommended) and the magnet on the door/window, or vice versa.
- Open the door/window fully to check that the placement of Strips and the magnet does not interfere with hinges or locking mechanisms.
To correctly mount Strips, please follow the steps below:
1. Make sure the surface is clean, dry, and at least +10°C(+50°F). Use the included cloth to clean and prepare the surfaces.
2. Remove the brown protective film from the small Strips test adhesive. This adhesive is used before the final placement, so it is easy to re-position Strips if needed.
3. Place Strips where you want them mounted. Check the position by carefully closing the door/window and then opening it completely again.
4. Identify where the magnet should be placed (See picture below). Remove the protective film and place the magnet. Close and open again to validate that your Z-Wave controller detected the changes. Re-position if needed.
5. Check that the door/window can be fully closed and opened and that your Z-Wave controller detects the changes.
6. When you are satisfied, mark the exact position for strips. Remove it from its position, remove the long film protecting the adhesive backing, and place strips exactly as you marked.
7. Keep the spare magnet; it can be used to wake up, remove, or reset Strips in the future. More guidance including instructional videos: www.sensative.com/strips
Magnet placement and sensor range
Check that the magnet can be placed so that it is less than 10 mm from the Strip‘s square end when the door/window is closed.
When the door/window is open, the magnet should be at least 30 mm away from the Strips
Installation Guidelines
https://sensative.com/download/strips-guard-detailed-mounting-guidelines/
Product Usage
To verify Strips is working properly
Move the squared magnet towards the square edge as shown in the picture. Check that your Z-Wave Controller displays the status correctly.
If your Z-Wave system doesn‘t respond, you may need to change strip‘s notification type from the controller.
LED Notification:
1 Short Blink
-User feedback during commands
-Successfully sent report
2 Short Blinks
- The indication when Strips are not added to a network
2 Long Blink
- A user command is successfully executed.
5 Short Blinks
- Error (e.g. communication with controller failed)
| Reset to factory default | 1. Take the magnet and move it to the rounded edge and wait for the blink, then move the magnet away. 2. Repeat this 3 times, but on the 3rd repetition, keep the magnet at the rounded edge for 10 seconds. A long LED signal indicates success. |
| Inclusion | 1. Open your Z-Wave Controller application and start pairing mode. 2. Remove both magnets from Strips.* 3. One long LED blink means Strips has been successfully added to your Z-Wave network. *If you have previously removed the magnets from Strips, or need to re-add the device, performing a manual wake up will join the device when the controller is in pairing mode. |
| Exclusion | 1. Take the magnet and move it to the rounded edge and wait for the blink, then move the magnet away. 2. Repeat this 3 times. A final short blink will confirm that the user-command was successful. |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 1 | Lifeline |
Configuration Parameters
Parameter 1: Notification type
Select the notification type for the door and window open or close events. Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | Binary sensor report + Notification report (Access Control) |
| 1 | Notification report (Access Control) |
| 2 | Notification report (Home Security) |
Parameter 2: LED indication
Turn On or Off LED for specific event indications (ex. alarms). Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | Turns off LED for door open events |
| 1 | On |
Parameter 15: Activate supervision
Activate Supervision command for onlyimportant alarm events or all events. Supervised commands require a confirmationfrom the gateway when a notification is received. Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | Events sent with S2 Encapsulation only |
| 1 | Only Door Open Alarm Report (Events sent with S2 and supervision encapsulation) |
| 2 | Unsolicited reports (Door Open/Close, Tamper clear, Wake-up notification and Battery Report events sent with S2 and supervision encapsulation) |
Parameter 16: Supervision report wait time
Only used if parameter 22 is set to 1 (High security). The number of milliseconds to wait for a Supervision response when a Supervised message is sent. Size: 2 Byte, Default Value: 10000
| Setting | Description |
|---|---|
| 500 - 30000 | (ms) |
Parameter 17: No. of failed event retries
Only used if parameter 22 is set to 1 (High security). Number of retries when a confirmation is not received. Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 - 5 | 0 = No retry, 1 - 5 = Number of retries when a confirmation is not received. |
Parameter 18: Failed Event Retry Interval
Only used if parameter 22 is set to 1 (High security). The minimum number of seconds between retries. Size: 1 Byte, Default Value: 6
| Setting | Description |
|---|---|
| 1 - 60 | Min = 1 second, Max = 60 seconds |
Parameter 19: Heartbeat interval
Only used if parameter 22 is set to 1 (High security). Number of minutes between periodic battery reports (Heartbeats). Size: 1 Byte, Default Value: 70
| Setting | Description |
|---|---|
| 5 - 70 | (mins) - Accepts multiples of 5 mins. - Any arbitary value in between 5 and 70 will be rounded up to a multiple of 5 |
Parameter 22: Security Level
Select the level of security. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | : Standard (Forces parameter behaviour as follows: #16=1000, #17=Sensative standard**, #18=0, #19=Off, #21=Off** Retries with an incrementally longer period until reconnected |
| 1 | : High Security (Enables parameters 16-19, 21) |
Technical Data
| Dimensions | 15 x 195 x 3 mm |
| Weight | 20 gr |
| Hardware Platform | EFR32ZG23 |
| EAN | 7350088520727 |
| IP Class | IP 65 |
| Battery Type | 1 * inside |
| Firmware Version | 36.27 |
| Z-Wave Version | 07.13 |
| Z-Wave Product Id | 019a.0004.0004 |
| Frequency | Europe - 868,4 Mhz |
| Maximum transmission power | 5 mW |