TP-Link Tapo

TP-Link Tapo L535E Smart Wi-Fi Light Bulb Multicolor E27

SKU: TPLLTAPOL535E

Quickstart

This is a Z-Wave Device for . To run this device please connect it to your mains power supply.

Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

What is Z-Wave?

Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.

Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.

This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.

If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.

For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.

Product Description

Tapo L535E Smart Wi-Fi RGB light bulb

Extra bright smart light bulb: With 1055 lumens (75 W equivalent) for clear, high-quality light, the Tapo L535E is ideal for all living spaces that require brighter lighting.

Millions of colours: Easily create scenarios for your daily routine or activities by adjusting the light brightness, light temperature and colours - with millions of shades to choose from via the Tapo app.

Matter certified: Supporting the Matter protocol, the Tapo L535E can work seamlessly with other certified products on different platforms.

Schedule & Timer: Create a regular schedule to switch on and off with your chosen lighting effects.

Voice control: Manage your smart lights with voice commands via Alexa, Siri or Google Assistant

Remote control and away mode: Switch connected devices on and off instantly via the Tapo app, no matter where you are. Switch on away mode to simulate that someone is at home.

Energy monitoring: Monitor the power consumption and costs of your connected devices in real time via the Tapo app.

No hub required: Connect directly to your home"s secure Wi-Fi network - no need for a hub or additional devices.

Features:

Form factor: E27
Brightness: 1055 lumen
Colour temperature range: 2500-6500 K
Switching cycles: 15000
Service life: 25,000 hours
Input voltage: 220 -240 V~, 50/60 Hz
Power consumption: 8.6 W
Standby power consumption: 0.4 W
Energy class E
Operating temperature: -15 ºC~40 ºC
Operating humidity: 10%~90%RH, non-condensing
Wireless protocol: Wi-Fi IEEE 802.11b/g/n, 2.4 GHz, Matter over Wi-Fi

Prepare for Installation / Reset

Please read the user manual before installing the product.

In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.

Safety Warning for Mains Powered Devices

ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.

Inclusion/Exclusion

On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.

Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.

Quick trouble shooting

Here are a few hints for network installation if things dont work as expected.

Make sure a device is in factory reset state before including. In doubt exclude before include.
If inclusion still fails, check if both devices use the same frequency.
Remove all dead devices from associations. Otherwise you will see severe delays.
Never use sleeping battery devices without a central controller.
Dont poll FLIRS devices.
Make sure to have enough mains powered device to benefit from the meshing

Technical Data

Dimensions	0.0600000x0.1150000x0.0600000 mm
Weight	61 gr
EAN	4895252502763
Frequency	XXfrequency
Maximum transmission power	XXantenna

Explanation of Z-Wave specific terms

Controller — is a Z-Wave device with capabilities to manage the network. Controllers are typically Gateways,Remote Controls or battery operated wall controllers.
Slave — is a Z-Wave device without capabilities to manage the network. Slaves can be sensors, actuators and even remote controls.
Primary Controller — is the central organizer of the network. It must be a controller. There can be only one primary controller in a Z-Wave network.
Inclusion — is the process of adding new Z-Wave devices into a network.
Exclusion — is the process of removing Z-Wave devices from the network.
Association — is a control relationship between a controlling device and a controlled device.
Wakeup Notification — is a special wireless message issued by a Z-Wave device to announces that is able to communicate.
Node Information Frame — is a special wireless message issued by a Z-Wave device to announce its capabilities and functions.