TESLA Smart Home
TechToy Smart Bulb RGB 4.5W GU10 Wi-Fi
SKU: TSLLLIG-GU10
Quickstart
This is a
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.What is Z-Wave?
Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.
This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.
If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.
For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.
Product Description
A smart bulb to light up any smart home. Choose from a wide range of matt colours. So you can be sure that these bulbs will provide the right atmosphere for any occasion. So it"s up to you whether you choose the brightness of daylight or prefer relaxing muted shades.
RGB Colours.
The smart bulb offers a full range of colour temperatures. Its range is from 2 700 K - 6 500 K RGB. In addition, it is also dimmable and allows you to adjust the white colour temperature.
Energy Saving.
The smart bulb has an electrical input of 4.5 W and a luminous intensity of 350 lumens. It is therefore an energy-saving bulb.
Easy Application.
Connect the lights to a smart app using Wi-Fi. Simply download the TESLA Smart app to your Android or iOS device. Working with the smart app is very clear and easy.
Create your own scenarios.
You can connect the bulbs to other smart home products. If you connect smart bulbs to a motion sensor, for example, you"ll never have to blindly search for a switch again. The moment you walk in the house your smart home will light up without you having to do anything else. The lights can also be controlled via remote control or app.
Dimming and temperature is up to you.
The smart bulb offers a large range of colour temperatures. Its range is from 2,700K - 6,500K RGB + CCT. In addition, it is also dimmable and allows you to adjust the white colour temperature. So you can play around with setting different room atmospheres. And you can be sure that you will always find the one you need.
Easy connection.
Connect the smart bulb with Wi-Fi and Bluetooth. This connection is very easy, fast and stable. Setup and subsequent operation will therefore not take long and will not cause you any difficulties.
Bulb setting.
Setting up a smart light bulb and its subsequent operation will not take you a long time and will not cause any difficulties.
Brighten up your home.
Quality lighting is important for every happy home. With the smart bulb with GU10 thread, you can give your home not only high-quality, but also smart lighting. The smart bulb is easy to set up and easy to operate, even for those who are not very experienced with modern technology. In addition, the smart assistants Google Home and Amazon Alexa, which can also control the bulb, make working with it even easier. Thanks to them, you"ll also be able to enter voice commands.
Features:
- Smart Bulb RGB 4.5W GU10 Wi-Fi
- ID: TSL-LIG-GU10
- Color of Light: RGB (16 million colours), Cold white, Warm white
- Light Temperature: 2700?6500 K
- Luminous Flux: 350 lm
- Socket: GU10
- Rated Power: ?0.5 W (Power in standby mode), 4.5 W
- Power Supply: 200–240 V AC 50/60Hz
- Operating Temperature: -10?40 °C
- Dimensions: 50 x 56 mm
- Connectivity: Wi-Fi 2.4 GHz IEEE 802.11b/g/n, Bluetooth
- App TESLA Smart: Google Android 6.0+, Apple iOS 11.0+
- Management App: SmartLife or Tuya Smart App
Prepare for Installation / Reset
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.
Safety Warning for Mains Powered Devices
ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.
Inclusion/Exclusion
On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.
Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.
Quick trouble shooting
Here are a few hints for network installation if things dont work as expected.
- Make sure a device is in factory reset state before including. In doubt exclude before include.
- If inclusion still fails, check if both devices use the same frequency.
- Remove all dead devices from associations. Otherwise you will see severe delays.
- Never use sleeping battery devices without a central controller.
- Dont poll FLIRS devices.
- Make sure to have enough mains powered device to benefit from the meshing
Technical Data
| Dimensions | 0.0500000x0.0500000x0.0560000 mm |
| Weight | 30 gr |
| EAN | 8596115842038 |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |
Explanation of Z-Wave specific terms
- Controller — is a Z-Wave device with capabilities to manage the network. Controllers are typically Gateways,Remote Controls or battery operated wall controllers.
- Slave — is a Z-Wave device without capabilities to manage the network. Slaves can be sensors, actuators and even remote controls.
- Primary Controller — is the central organizer of the network. It must be a controller. There can be only one primary controller in a Z-Wave network.
- Inclusion — is the process of adding new Z-Wave devices into a network.
- Exclusion — is the process of removing Z-Wave devices from the network.
- Association — is a control relationship between a controlling device and a controlled device.
- Wakeup Notification — is a special wireless message issued by a Z-Wave device to announces that is able to communicate.
- Node Information Frame — is a special wireless message issued by a Z-Wave device to announce its capabilities and functions.