TESLA Smart Home
TESLA Smart Home Smart Power Strip 3 + 4 USB Wi-Fi
SKU: TSLLSPL-3-4USB
Quickstart
This is a
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.What is Z-Wave?
Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.
This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.
If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.
For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.
Product Description
If you want to control more devices remotely, Power Strip is the right choice. It allows you to control up to seven devices individually while keeping an eye on the power flow and energy consumption. This allows you to better optimise the economics of your household and save money on energy costs.
Continuous Overview Of Your Power Consumption.
A smart plug allows you to keep track of exactly how much electricity is flowing through it. You can keep an eye on this data at all times.
Separate Control.
You can control the outlets and USB ports separately. You can thus conveniently manage each and every device that is connected to the Power Strip.
A Wide Range Of Automation Options.
Thanks to the TESLA Smart app on your phone, you can set up the individual outlets and USB ports as required. Setting up is easy – it won"t take you more than a few minutes.
Easy to use.
Manage all outlets and USB ports via one app on your iOS or Android phone or tablet. You can control each outlet and each USB port separately. In addition, the app shows you at any time and at any place whether the outlet or port is currently on or off. So an iron that you forgot to unplug will trouble you no more. A smart plug can turn your home into not only a smarter but also a safer place to live.
Assistants for the greatest convenience.
The TESLA Smart app controlling the smart plug can be connected to the smart personal assistants Google Assistant or Amazon Alexa. These allow you to control the device with your voice, making the use of the plug even easier.
Up to 3 devices with 4 USB ports.
Manage all outlets and USB ports via one app on your iOS or Android phone or tablet.
Turn ordinary appliances into smart ones.
Thanks to the app, the smart plug offers plenty of automation options. One of its great advantages is the ability to turn even ordinary appliances into smart devices. The possibility to control each outlet separately comes in handy if, for instance, you have an ordinary lamp in one outlet and wireless headphones in the other. At this point, you can start charging the wireless headphones remotely without turning on the lamp.
Features:
- A smart plug for connecting up to 3 devices with 4 USB ports
- ID: TSL-SPL-3+4
- Maximum Current of one USB: 2.4 A
- Maximum Load: 16 A / 3680 W
- Power Supply: 220?240 V AC 50 Hz
- Operating Temperature: 0?35 °C
- Operation Humidity: 5–65 %
- Connectivity: Wi-Fi 2.4 GHz IEEE 802.11b/g/n
- App TESLA Smart: Google Android 6.0+, Apple iOS 11.0+
- Management App: SmartLife or Tuya Smart App
Prepare for Installation / Reset
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.
Safety Warning for Mains Powered Devices
ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.
Inclusion/Exclusion
On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.
Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.
Quick trouble shooting
Here are a few hints for network installation if things dont work as expected.
- Make sure a device is in factory reset state before including. In doubt exclude before include.
- If inclusion still fails, check if both devices use the same frequency.
- Remove all dead devices from associations. Otherwise you will see severe delays.
- Never use sleeping battery devices without a central controller.
- Dont poll FLIRS devices.
- Make sure to have enough mains powered device to benefit from the meshing
Technical Data
| Dimensions | 0.0700000x0.0450000x0.3400000 mm |
| Weight | 742 gr |
| EAN | 8596115815131 |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |
Explanation of Z-Wave specific terms
- Controller — is a Z-Wave device with capabilities to manage the network. Controllers are typically Gateways,Remote Controls or battery operated wall controllers.
- Slave — is a Z-Wave device without capabilities to manage the network. Slaves can be sensors, actuators and even remote controls.
- Primary Controller — is the central organizer of the network. It must be a controller. There can be only one primary controller in a Z-Wave network.
- Inclusion — is the process of adding new Z-Wave devices into a network.
- Exclusion — is the process of removing Z-Wave devices from the network.
- Association — is a control relationship between a controlling device and a controlled device.
- Wakeup Notification — is a special wireless message issued by a Z-Wave device to announces that is able to communicate.
- Node Information Frame — is a special wireless message issued by a Z-Wave device to announce its capabilities and functions.